ETC ColorSource Raceway User manual

Part Number: 7199M2100 Rev: C
Released: 2019-07
ColorSource Raceway
Installation Manual

To view a list of ETC trademarks and patents, go to etcconnect.com/ip . All other trademarks, both
marked and not marked, are the property of their respective owners.
ETC intends this document, whether printed or electronic, to be provided in its entirety.This
product is intended for professional use only. Read this entire document before using this product.

Table of Contents i
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Document Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Help from ETC Technical Services . . . . . . . . . . . . . . . . . . . . . . .2
Before you begin . . . . . . . . . . . . . . . . . . . . . . . . .3
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Maximum span . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Maximum load (suspended mount) . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Maximum length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Outlet types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Mounting bracket types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Check shipment before assembly . . . . . . . . . . . . . . . . . . . . . . .8
Prepare for assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Tools required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Assemble ColorSource Raceway . . . . . . . . . . . . . . . . . . . . . . . .9
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Wall/ceiling mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Catwalk mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Grid mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Install grid-mount brackets without work lights. . . . . . . . . . . . . . . . .13
Install grid-mount brackets with work lights . . . . . . . . . . . . . . . . . . .15
Suspended mount, Dual batten suspended mount,
or Prodigy RACA mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Install hanger adapter on suspended-mount hanger brackets
for threaded rod or Unistrut suspension (optional) . . . . . . . . . . . . . .21
Assemble ETC aluminum batten. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Attach batten to hanger brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Attach work lights to hanger brackets . . . . . . . . . . . . . . . . . . . . . . . .23
Prodigy FlyPipe mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Attach work lights to Prodigy FlyPipe . . . . . . . . . . . . . . . . . . . . . . . . .26
Add a batten accessory to Prodigy FlyPipe . . . . . . . . . . . . . . . . . . . . .27
Connect work lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

ii ColorSource Raceway Installation Manual
Connect power and data . . . . . . . . . . . . . . . . .31
Hardwired version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Connector versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
DMX Active Pass-thru Connectors . . . . . . . . . .34
About the LED indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Update firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Introduction 1
Introduction
Welcome to the ColorSource Raceway Installation Manual . This document will guide you
through the assembly, setup, and use of the ColorSource Raceway.
Document Conventions
This document uses the following conventions to draw your attention to important
information.
All ETC documents are available for free download from our website: etcconnect.com.
Please e-mail comments about this manual to: [email protected].
Note:
Notes are helpful hints and information that is supplemental to the main text.
CAUTION:
A Caution statement indicates situations where there may be undefined or
unwanted consequences of an action, potential for data loss or an equipment
problem.
WARNING: A Warning statement indicates situations where damage may occur, people
may be harmed, or there are serious or dangerous consequences of an action.
WARNING: RISK OF ELECTRIC SHOCK! This warning statement indicates situations where
there is a risk of electric shock.

2ColorSource Raceway Installation Manual
Help from ETC Technical Services
If you are having difficulties, and your problem is not addressed by this document, try the ETC
support website at support.etcconnect.com or the main ETC website at etcconnect.com. If
none of these resources are sufficient, contact ETC Technical Services directly at one of the
offices identified below. Emergency service is available from all ETC offices outside of normal
business hours.
When calling for help, take these steps first:
• Prepare a detailed description of the problem
• Go near the equipment for troubleshooting
• Find the project number for your specific ColorSource Raceway installation (located on the
termination box)
• Find your notification number if you have called in previously
Americas United Kingdom
ETC, Inc. ETC Ltd - UK
Technical Services Department Technical Services Department
3031 Pleasant View Road 26-28 Victoria Industrial Estate
Middleton, WI 53562 Victoria Road,
800-775-4382 (USA, toll-free) London W3 6UU England
[phone] [phone]
[email protected] te[email protected]
Asia Germany
ETC Asia ETC GmbH
Technical Services Department Technical Services Department
Room 1801, 18/F Ohmstrasse 3
Tower 1, Phase 1 Enterprise Square 83607 Holzkirchen, Germany
9 Sheung Yuet Road [phone]
Kowloon Bay, Kowloon, Hong Kong [email protected]
[phone]
[email protected]
France
ETC France
62-64 rue Danielle
Casanova
Saint-Denis Cedex
F93200
[phone]
[email protected]

Before you begin 3
Before you begin
Overview
The ColorSource Raceway provides power and data in a lightweight, sleek profile that is perfect for
all-LED systems.
Safety
Consult your project drawing for the dimensions and weight of your specific ColorSource Raceway
system.
Maximum span
When mounting the ColorSource Raceway, position brackets no more than 10 ft (3 m) apart.
Maximum load (suspended mount)
The batten on the ColorSource Raceway supports a distributed load of 150 lb (68 kg) and a point load
of 65 lb (30 kg) across a 10 ft (3 m) span (see image below).
Maximum length
The ColorSource Raceway cannot exceed 72 ft (22 m) in length (74 ft [23 m] in batten length).
WARNING: Suspending the ColorSource Raceway from brackets more than 10 ft (3 m)
apart risks structural failure and is not an approved use of this product.
CAUTION:
• Verify that the mounting structure is capable of supporting the weight of
the ColorSource Raceway. Always follow applicable building codes when
attaching ColorSource Raceway to structural elements.
• When using the ETC aluminum batten for ColorSource Raceway, choose
clamps designed for use with an aluminum batten instead of C-clamps to
avoid damage to the batten.
Note:
For suspended-mount installations, do not hang the ColorSource Raceway until after
you attach the batten.
Maximum 10 ft (3 m) span
Point load = 65 lb (30 kg)
Uniform distributed load = 150 lb (68 kg)
Junction bracket
ColorSource Raceway (rear view)

4ColorSource Raceway Installation Manual
Specifications
Outlet types
Mounting bracket types
The following brackets are available for mounting the ColorSource Raceway. All hanger brackets that
support a batten are compatible with ETC aluminum batten and 1.5 in (1.9 in OD) Schedule 40 steel
pipe.
• Single Edison (NEMA 5-20R)
• Dual Edison (NEMA 5-20R)
• Stage pin (20A)
• Twist-Lock L5-20R (20A)
•NEUTRIK
®powerCON®TRUE1
• 15A UK Round Pin
• 15A UK Square Pin
•16ACEE
• 16A SCHUKO®
• Japanese "C" connector
• DMX Active Pass-thru connector
• Ethernet (passive connector)
Type Description and
Part Number Image Supports batten?
Integrated
work light
mounting?
111
Wall/Ceiling Mount
(7199A1011)
See
Wall/ceiling
mount
on page 10 .
No
No
(Work lights
are allowed,
but mounting
hardware is
not included)
115
Variable Grid Mount
(7199A1015)
See
Grid mount on
page 13 .
No Yes
119
Prodigy
FlyPipe Mount
(7199A1019)
See
Prodigy FlyPipe
mount
on page 25 .
Yes
(See
Batten
Accessory
for Prodigy
FlyPipe
Mount
on
page 5 )
Yes
Wall
mount
Ceiling
mount
Vertical
orientation
Horizontal
orientation
Anti-rotation
stabilizer, not
intended for
support
U-bolts connect
hanger bracket to
structural pipe
FlyPipe

Before you begin 5
NA
Batten Accessory for
Prodigy FlyPipe
Mount
See
Prodigy FlyPipe
mount
on page 25 .
Yes Yes
121
Suspended Mount
Hanger Bracket
(7199A1021)
See Suspended
mount, Dual batten
suspended mount, or
Prodigy RACA mount
on
page 19 .
Yes Yes
122
Suspended Mount
Hanger Bracket for
Termination Box
(7199A1022)
See
Suspended
mount, Dual batten
suspended mount, or
Prodigy RACA mount
on page 19 .
Yes Yes
Type Description and
Part Number Image Supports batten?
Integrated
work light
mounting?
FlyPipe

6ColorSource Raceway Installation Manual
123
Threaded
Rod/Unistrut
Suspension Accessory
(7199A1023)
See
Suspended
mount, Dual batten
suspended mount, or
Prodigy RACA mount
on
page 19 .
Yes Yes
126
Dual Batten
Suspended Mount
Hanger Bracket
(7199A1026)
See Suspended
mount, Dual batten
suspended mount, or
Prodigy RACA mount
on
page 19 .
Yes Yes
127
Dual Batten
Suspended Mount
Hanger Bracket for
Termination Box
(7199A1027)
See
Suspended
mount, Dual batten
suspended mount, or
Prodigy RACA mount
on
page 19 .
Yes Yes
Type Description and
Part Number Image Supports batten?
Integrated
work light
mounting?
Accessory
attaches to the
top of hanger
brackets (types
121, 122, 126,
and 127

Before you begin 7
NA
Prodigy RACA Mount
Hanger Bracket
(8000A1185)
See
Suspended
mount, Dual batten
suspended mount, or
Prodigy RACA mount
on
page 19 .
Yes Yes
NA
Prodigy RACA Mount
Hanger Bracket for
Termination Box
(8000A1186)
See
Suspended
mount, Dual batten
suspended mount, or
Prodigy RACA mount
on page 19 .
Yes Yes
Type Description and
Part Number Image Supports batten?
Integrated
work light
mounting?
Front view
Front view

8ColorSource Raceway Installation Manual
Check shipment before assembly
Open each package and check the contents against your packing slip and prints to ensure that you
install the ColorSource Raceway in the correct location. After you open the packages, examine the
contents for any damage from shipping. Wire between sections should be undamaged. Metal parts
should be free from dents or scratches. Contact your ETC project manager or Customer Service at an
ETC office if you discover any problems. For ETC contact information, see
Help from ETC Technical
Services
on page 2 .
Prepare for assembly
When fully assembled, the ColorSource Raceway can be long and difficult to move. Plan to assemble
the ColorSource Raceway in an area with good access to the final installation location.
Tools required
•#2POZIDRIV
® screwdriver (for junction brackets)
• #3 Phillips screwdriver (for FlyPipe brackets)
• 13 mm socket wrench (for hanger brackets and Prodigy FlyPipe batten accessory)
•TORX
®T30 bit and impact driver (for batten assembly screws)
• 10 mm socket driver for anti-rotation self-drill screws (for ETC aluminum batten)
• 19 mm wrench (for optional threaded rod/Unistrut hanger accessory)
• Small flat-blade screwdriver (for wiring)
134
Catwalk Mount
(7199A1034)
See
Catwalk mount
on page 11 .
No
No
(Work lights
are allowed,
but mounting
hardware is
not included)
Type Description and
Part Number Image Supports batten?
Integrated
work light
mounting?
U-bolts that support
ColorSource Raceway
attach to catwalk

Assembly 9
Assembly
Assemble ColorSource Raceway
1: Take the folded ColorSource Raceway out of the packaging and lay it out straight, face down,
on a flat surface. Leave the foam shipping collars on as long as possible to protect the sections
during assembly. Junction brackets are pre-attached to one end of each section.
2: Loosen the screws slightly on the pre-attached junction bracket.
3: Align the ends of the sections and slide the junction bracket into place.
4: Secure the pre-attached junction bracket with the provided M4 POZIDRIV screws, and tighten all
12 screws.
5: Repeat the process for the remaining sections.
2: Loosen
screws (x6)
4: Secure and tighten
screws (x12)
3: Align
and slide
Foam shipping collar

10 ColorSource Raceway Installation Manual
Installation
Wall/ceiling mount
1: Identify the locations where the ColorSource Raceway will be supported. Make sure that the
termination box will not be enclosed in mounting brackets.
2: Attach brackets for the bottom of the
ColorSource Raceway to the wall or
ceiling using appropriate M6 (¼ in)
fasteners (not provided), and then
position the ColorSource Raceway in
the brackets.
3: Attach brackets for the top of the
ColorSource Raceway.
CAUTION:
Verify that the mounting structure is capable of supporting the weight of the
ColorSource Raceway. Always follow applicable building codes when
attaching ColorSource Raceway to structural elements. Use appropriate
hardware when mounting ColorSource Raceway.
Attach top and bottom bracket
(hardware not included)

Installation 11
Catwalk mount
To mount the ColorSource Raceway on a catwalk, the catwalk railing centers must be within
10½–18½ inches (27–47 cm) of each other.
1: Identify the locations on the catwalk railings where the ColorSource Raceway will be supported.
Make sure that the termination box will not be enclosed in mounting brackets.
2: Determine the appropriate attachment position for the upper sides of the brackets, and then use
the provided U-bolts and nuts to secure the brackets to the railing in that position.
3: Attach the lower sides of the brackets to the lower railing using the provided U-bolts and nuts,
and adjust the U-bolts in the slots on the lower sides of the brackets as needed to fit.
2: Attach
upper U-bolt
in appropriate
position
3: Attach lower
U-bolt and
adjust as
needed

12 ColorSource Raceway Installation Manual
4: When both upper and lower U-bolts are positioned appropriately, tighten all U-bolt nuts.
5: Attach the lower raceway hardware to the mounting brackets as shown below.
6: Set the ColorSource Raceway into the lower raceway hardware, and secure by attaching the
upper raceway hardware.
5: Attach
lower hardware
6: Secure raceway with
upper hardware
Finished bracket

Installation 13
Grid mount
The grid mount hardware allows you to support the ColorSource Raceway on a grid or above a single
pipe, either in a vertical or horizontal orientation. You can also attach a work light to a grid mount
bracket.
Install grid-mount brackets without work lights
1: Determine whether you will mount the ColorSource Raceway using the brackets in the vertical
orientation or horizontal orientation, and then assemble the bracket hardware as needed.
CAUTION:
Grid or pipe must be separately supported using appropriate hardware. The
ColorSource Raceway grid mount cannot support the grid or pipe, and is
intended only to support the ColorSource Raceway.
Assemble raceway hardware Assemble mounting hardware Finished bracket
Vertical orientation
Optional anti-rotation
stabilizer, not
intended for support

14 ColorSource Raceway Installation Manual
2: Install the ColorSource Raceway:
Vertical orientation
a: Identify the locations on the grid where the ColorSource Raceway will be supported, and then
attach the brackets to the grid using the provided U-bolts and nuts. Make sure that the
termination box will not be enclosed in mounting brackets.
b: Loosen the sliding raceway brackets, position the ColorSource Raceway in the brackets, and
then tighten to fit.
Horizontal orientation
a: Identify the locations on the grid where the ColorSource Raceway will be supported. Make
sure that the termination box will not be enclosed in mounting brackets.
b: Attach brackets to the ColorSource Raceway, and then attach the brackets to the grid using
the provided U-bolts and nuts.
Assemble raceway hardware
Assemble mounting hardware
Finished bracket
Horizontal orientation
Optional anti-rotation
stabilizer, not
intended for support
Loosen sliding raceway
bracket, position
raceway in bracket, and
then tighten to fit
Vertical orientation Horizontal orientation

Installation 15
Install grid-mount brackets with work lights
1: Determine whether you will mount the ColorSource Raceway using the brackets in the vertical
orientation or horizontal orientation, and then attach the transition-box base to the bracket
mounting plate as shown below.
Set aside the transition-box cover and remaining hardware. You will use the transition box to
store the excess cord connecting the work light to the ColorSource Raceway. See
Connect work
lights
on page 29 .
Note:
The orientation of the transition box differs between the vertical and horizontal
orientation of the grid mount brackets. Note that in the images below, the opening
at the bottom of the transition box is always oriented toward the bottom of the
image.
Transition box
(both base and
cover shown)
Attach transition-box base to
bracket mounting plate
(side view, angle view)
Make sure that the opening is
at the bottom before attaching
box to bracket mounting plate
Attach transition-box base to
bracket mounting plate
(side view, angle view)
Vertical orientation Horizontal orientation

16 ColorSource Raceway Installation Manual
2: Assemble the bracket hardware in either the vertical or horizontal orientation.
Assemble raceway hardware Assemble mounting hardware Finished bracket
Vertical orientation
Assemble raceway hardware
Assemble mounting hardware
Finished bracket
Horizontal orientation
Optional anti-rotation
stabilizer, not
intended for support