Circutor CIRWATT Series User manual

MULTI-PURPOSE
THREE PHASE METER
CIRWATT Series
(Version 4.xx)
Installation Man al
(M98166301-03 / 05A)
(c) CIRCUTOR S.A.

Page No. 1
INSTALLATION MANUAL TABLE OF CONTENTS PAGE No.
1.- INTRODUCTION ..................................................................................... 2
2.- METER MODEL ....................................................................................... 2
3.- SAFETY LEVELS (Seals) ......................................................................... 3
4.- DISPLAY ................................................................................................. 3
4.1.- Dis lay Modes. ..................................................................................... 4
4.1.1.- STAND BY Mode ............................................................................... 4
4.1.2.- READING Mode ................................................................................. 4
4.2.- Ty es of screen. ...................................................................................... 5
4.2.1.- Stand by screen ................................................................................. 5
4.2.2.- Menu Screen ..................................................................................... 5
4.2.3.- Data Screen. ...................................................................................... 5
4.3.- STAND BY mode screen .......................................................................... 6
4.4.- READING screens mode. ......................................................................... 7
4.4.1.1.- Screen L1 (CONTRACT 1) ........................................................... 8
4.4.1.2.- Screen L2 (CONTRACT 2) ......................................................... 12
4.4.1.3.- Screen L3 (CONTRACT 3) ......................................................... 13
4.4.1.4.- Screen L4 (INFORMATION) ....................................................... 15
4.4.1.5.- Screen L5 (INFO FAB) ............................................................... 20
5.- TECHNICAL FEATURES ........................................................................ 22
6.- INSTALLATION AND START-UP ............................................................ 24
6.1.- Installing the equi ment .......................................................................... 24
6.2.- Meter terminals ratio (see label on terminal cover) .................................... 24
6.3.- Meter connection diagrams ..................................................................... 25
7.- MAINTENANCE ..................................................................................... 26
8.- TECHNICAL SERVICE ........................................................................... 26
A.- CIRWATT connection diagram ..................................................................... 27
B.- Changing the Battery ................................................................................... 28

Page No. 2
1.- INTRODUCTION
CIRWATT is a multi- ur ose three- hase, four quadrant, digital meter. Its great
versatility is its main feature, allowing it to ada t to the needs of the individual user.
It has been es ecially designed for installations where the electro-mechanical meters
do not meet the current requirements. It is s ecifically for those installations that require a
meter with a tariff system or where electricity billing is done by using load rofiles.
2.- METER MODEL
The different meter configuration o tions covering the needs of each installation are
shown below:
Meter version CIRWATT 

 



- 







- 





- 




4 wire / 3 wire 4 Connection
mode
Class 0.5S active / Class 1
reactive 05
Class 0.2S active / Class 0.5
reactive 02
Acc racy
3x57/100 V (4 w) L
3x63.5/110 V (4 w) M
3x127/220 V (4 w) N
3x220/380 V (4 w) O
3x230/400 V (4 w) Q
3x110/190 V (4 w) T
Meas red
voltage
/5 (10) A three hase T5
/1 (2) A three hase T1
Meas red
c rrent
50 Hz A Freq ency
60 Hz B
RS-232 / RS-232 1
RS-232 / RS-485 2
Comm nications
company/ ser
Without card 0
3 in uts 1 Expansion card
4 out uts (o tomos) 2
4 out uts (relay) 3
3 in uts + 4 out uts (o tomos) 4
3 in uts + 4 out uts (relay) 5
Meter + Tariff setter + Power
demand meter + Recorder D Mode
Version and/or rotocols Revision

Page No. 3
3.- SAFETY LEVELS (Seals)
CIRWATT has the necessary seals
to ensure that the meter is not tam ered
with. Once the meter is installed, these
seals must always be attached.
⇒ Terminal cover seals.
These seals are attached once the
equi ment has been installed. These seals
revent the modification of the meter
connection.
⇒ Meter cover seal
Bill closure and changing the
clock's battery are rotected by this seal.
4.- DISPLAY
Data is resented on a three line LCD dis lay es ecially designed for the CIRWATT.
CONSUMED
ENERGY
GENERATED
ENERGY
INDUCTIVE AND
CAPACITIVE
SYSTEM
ACTIVE
TARIFF
Using the key the menus may be accessed. And with the key it is ossible to
move through the menu.
The units and resolution of the energy values are the same as for the meter overflow
values, i.e. the recorder values. The units will be kWh or kVArh.
The size of the recordings will be as shown below:
Ty e 1 (Class 0.2S) 9 whole digits (999,999,999)
Ty e 2 (Class 0.5S) 8 whole digits (99,999,999)
Ty e 3 (Class 1) 7 whole digits (9,999,999)
For Ty e 1 measuring equi ment, the dis lay screen only has 8 digits, in this case it
will act as follows:
Overflow (Recorder)
9 whole digits Unit kWh or kVArh (999,999,999)
Display (Screen)
6 whole digits and 2 decimals Unit MWh or MVArh (999,999.99)
METER COVER
SEAL
TERMINAL CASING
SEALS
CHANGE SCREEN
GROUP BUTTON
CHANGE SCREEN
BUTTON

Page No. 4
The nits for any power or energy data transmitted via the protocol will
be kW, kWh, kvarh, regardless of how they are displayed.
4.1.- Display Modes.
4.1.1.- STAND BY Mode
Whenever READING mode is not activated by ressing the corres onding
reading button/s, this screen will always a ear as a default.
4.1.2.- READING Mode
This is activated by ressing , entering the variable selection menu. Pressing
the key moves through the menu and by ressing , enters the o tion that is
flashing on the dis lay. 60 seconds after the last ress, the Dis lay returns to STAND
BY Mode.

Page No. 5
4.2.- Types of screen.
There are three ty es of screen:
4.2.1.- Stand by screen
The STAND BY screen resents information without needing to use any of the
equi ment's buttons. This is ty ically used to show to the customer the necessary
information for him to control measurement in the easiest way ossible.
In the case of the 4x20 dis lay (4 line screen), the second is a SCROLL screen
( resenting different information in a different way after a time)
4.2.2.- Men Screen
The MENU screen resents different o tions to access data screens or other
secondary menu screens.
It is only used in READING mode.
=ihnl[]n{+
Ch@i
Ch@i{@[\
F-{{
N+{=H<
4.2.3.- Data Screen.
The DATA screens show information on a s ecific grou of data. It is only used in
READING mode.
The data lines consist of two fields: one code (9 characters reserved) and the value of
the data
****+.2*{{+(+2(+
****,-12{{+(+2(+
****+23+{{+(/2(+
F-{{ N+{=H<
L(****+{{{J
****+
****/,*{{ *(+2(*
*24-/4/*{{{
,3(+*(*-
F-{{ N+{=H<

Page No. 6
4.3.- STAND BY mode screen
Screens Text Type Comments
r.xxxxx P.xxxxx FIXED Link Address and Measurement Point
OBIS Without OBIS
0.18.0
0.28.0
0.58.0
0.68.0
0.78.0
0.88.0
IMP
EXP
Q1
Q2
Q3
Q4
SCROLL
Absolute active energy in ut total
Absolute active energy out ut total
Total Q1absolute reactive energy
Total Q2 absolute reactive energy
Total Q3 absolute reactive energy
Total Q4 absolute reactive energy
DD-MM-YYYY HH:MM:SS
FIXED Date and Local Time
Alphan meric indicators line
Q1 Quadrant (Q1, Q2, Q3, Q4) (See APPENDIX C)
1+2+3+ Presence of voltage in each hase with its corres onding current
direction
T123 Current tariff eriods in contracts 1, 2 and 3 res ectively
C Critical alarm due to internal or external incidents directly affecting
measurement. This will be flashing.
N Non critical alarm not affecting measurement creating a meter
malfunction. This will be flashing.
B Low battery alarm. This will be flashing.
R
P S ecial arameter mode activated
Code field
B. C D. E. F xxxxxxxx
B. 1 character long. Defines the contract corres onding to the data. It may take the values
0,1,2 or 3. 0 is used for data not associated with any contract
C 1 or 2 characters long according to circumstances. Generally defines the hysical or
abstract size of the data. It may take the values defined in the IEC/UNE-EN62056-61
OBIS standard
D. 1or 2 characters long according to circumstances. Defines the ty e or result
E. 1 character long. Generally defines the tariff for the value defined by B, C and D. It may
take the values 0 to 9 defined in the IEC/UNE-EN62056-61 OBIS standard
F 2 characters long. Defines the invoice eriod number from most recent to oldest of values
defined by B, C, D and E. It may take the values defined in the IEC/UNE-EN62056-61
OBIS standard
Xxxxxxxx
Values

Page No. 7
4.4.- READING screens mode.
_On.SerIES
R
(STAND
BYBY)
L
(MAIN)
L4
InFo
BACK
L40
(INDICATORS)
NodEl
L41
(CONTRACT PARAMETERS)
L42
(TRANSFORMATION RATIOS)
MANU ADD
L43
CURRENT VALUES
ContrASt
L44
INSTANT VALUES
BACK
L45
(COMMUNICATIONS)
L46
(IDENTIFIERS)
L47
(OUTPUT CONSTANTS
SALIDA)
L48
(CLOCK CHANGE)
BACK
L1
()
ConTRACT 1
L11
()
CURRENT
L31
()
CURRENT
L12
()
CLOSURE 1
L32
()
CLOSURE 1
L13
()
CLOSURE 2
L33
()
CLOSURE 2
L14
()
CLOSURE 3
L34
()
CLOSURE 3
L15
()
CLOSURE 4
L35
()
CLOSURE 4
L16
()
CLOSURE 5
L36
()
CLOSURE 5
L17
()
CLOSURE 6
L37
()
CLOSURE 6
BACK
BACK
L2
()
ConTRACT 2
L3
()
ConTRACT 3
InFo FAb
L21
()
CURRENT
L22
()
CLOSURE 1
L23
()
CLOSURE 2
L24
()
CLOSURE 3
L25
()
CLOSURE 4
L26
()
CLOSURE 5
L27
()
CLOSURE 6
BACK
Abs
Abs
Abs
Abs
InC
InC
InC
InC

Page No. 8
Screen L (Main)
This is the first screen accessed in READING Mode. It is a MENU screen to access
other secondary MENU screens.
Screens Text Comments
=ihnl;]n{+{ Accesses current values for contract 1
=ihnl;]n{,{ Accesses current values for contract 2
=ihnl;]n{-{ Accesses current values for contract 3
Ch@i{ Accesses information not relevant to the contracts
Ch@i{@;\{ Accesses extra information defined by the
manufacturer:
L
<[=E{ Returns to STAND BY screen
4.4.1.1.- Screen L1 (CONTRACT 1)
This is the screen that accesses information on contract 1. It is a MENU screen. It
accesses the secondary MENU screens.
Screens Text Comments
=oll_ht Accesses current values for contract 1
=FI OL?{+ >>'GG'
SS
this shows information on values from contract 1
closure 1(most recent).
=FI OL?{, >>'GG'
SS
Accesses values for contract 1 closure 2
=FI OL?{- >>'GG'
SS
Accesses values for contract 1 closure 3
=FI OL?{. >>'GG'
SS
Accesses values for contract 1 closure 4
=FI OL?{/ >>'GG'
SS
Accesses values for contract 1 closure 5
=FI OL?{0 >>'GG'
SS
Accesses values for contract 1 closure 6 (oldest)
L1
<[]e{ Returns to the revious screen
4.4.1.1.1. Screen L11 (CONTRACT 1): CURRENT)
This screen shows information on the current values for contract 1. On entering this
menu two o tions a ear for data dis lay: absolute values and incremental values.
The ABSOLUTE o tion (;<
;<;<
;< ) dis lays absolute values for active and reactive
energy, as well as ower excesses and maximum demands.
The INCREMENTAL o tion (CH=
CH=CH=
CH=) dis lays incremental values for active and
reactive energy from the last bill closure, as well as ower excesses and maximum
demands.
If no o tion is selected, after the following ress it will dis lay data in Absolute values
as a default.
Either of the two screens will only dis lay information when it is active, that is to say, if
certain tariffs or recordings such as excesses or maximums have not been activated, they
will not a ear on the information screen for these tariffs and recordings.
The codes for Absolute values are shown below:
AbS (Absol te)
OBIS Witho t OBIS
L11
KWH 1.18.1 ABSIMP T1 C1-CUR
Tariff eriods for Active Energy

Page No. 9
KWH 1.18.2 ABSIMP T2 C1-CUR
KWH 1.18.3 ABSIMP T3 C1- CUR
KWH 1.18.4 ABSIMP T4 C1- CUR
KWH 1.18.5 ABSIMP T5 C1- CUR
KWH 1.18.6 ABSIMP T5 C1- CUR
KWH 1.18.0 ABSIMP TOTAL
C1- CUR
from the start of measurement
(if active), included in the total
( eriod 0)
1.18.x where x = tariff
( eriod)
KVARL 1.58.1 ABSQ1 T1 C1- CUR
KVARL 1.58.2 ABSQ1 T2 C1- CUR
KVARL 1.58.3 ABSQ1 T3 C1- CUR
KVARL 1.58.4 ABSQ1 T4 C1- CUR
KVARL 1.58.5 ABSQ1 T5 C1- CUR
KVARL 1.58.6 ABSQ1 T6 C1- CUR
KVARL 1.58.0 ABSQ1 TOTAL
C1-CO1
Tariff eriods for Q1 Reactive
Energy from the start of
measurement (if active),
included in the total ( eriod 0)
1.58.x where x = tariff
( eriod)
Power Excesses 1.12.1 EXCES T1 C1- CUR
Power Excesses 1.12.2 EXCES T2 C1- CUR
Power Excesses 1.12.3 EXCES T3 C1- CUR
Power Excesses 1.12.4 EXCES T4 C1- CUR
Power Excesses 1.12.5 EXCES T5 C1- CUR
Power Excesses 1.12.6 EXCES T6 C1- CUR
Excesses from the last bill
closure (if active)
1.12.x where x = tariff
( eriod)
MAXIMUMS 1.16.1 MAXDEM T1 C1-CUR
MAXIMUMS 1.16.2 MAXDEM T2 C1-CUR
MAXIMUMS 1.16.3 MAXDEM T3 C1-CUR
MAXIMUMS 1.16.4 MAXDEM T4 C1-CUR
MAXIMUMS 1.16.5 MAXDEM T4 C1-CUR
MAXIMUMS 1.16.6 MAXDEM T6 C1-CUR
MAXIMUMS 1.16.0 MAXDEM TOTAL
C1- CUR
Maximums from bill closure (if
active), included in the total
( eriod 0)
1.16.x where x = tariff
( eriod)
The codes for the absolute variable values are shown below:
Inc (Incremental))
OBIS Whio t OBIS
KWH 1.19.1 INCIMP T1 C1-CUR
KWH 1.19.2 INCIMP T2 C1-CUR
KWH 1.19.3 INCIMP T3 C1-CUR
KWH 1.19.4 INCIMP T4 C1-CUR
KWH 1.19.5 INCIMP T5 C1-CUR
KWH 1.19.6 INCIMP T5 C1-CUR
KWH 1.19.0 INCIMP TOTAL
C1-CUR
Consum tion er Active Energy
tariff eriod from the last bill
closure (if active) included in the
total
1.19.x where x = tariff
( eriod)
KVARL 1.59.1 INCQ1 T1 C1-CUR
KVARL 1.59.2 INCQ1 T2 C1-CUR
KVARL 1.59.3 INCQ1 T3 C1-CUR
KVARL 1.59.4 INCQ1 T4 C1-CUR
KVARL 1.59.5 INCQ1 T5 C1-CUR
KVARL 1.59.6 INCQ1 T6 C1-CUR
KVARL 1.59.0 INCQ1 TOTAL
C1-CUR
Consum tion er Q1 Reactive
Energy from the last bill closure
(if active), included in the total
1.59.x where x = tariff
( eriod)
Power Excesses 1.12.1 EXCES T1 C1-CUR
Power Excesses 1.12.2 EXCES T2 C1-CUR
Power Excesses 1.12.3 EXCES T3 C1-CUR
Power Excesses 1.12.4 EXCES T4 C1-CUR
L11
Power Excesses 1.12.5 EXCES T5 C1-CUR
Excesses from the last bill
closure(if active)
1.12.x where x = tariff
( eriod)

Page No. 10
Power Excesses 1.12.6 EXCES T6 C1-CUR ( eriod)
MAXIMUMS 1.16.1 MAXDEM T1 C1-CUR
MAXIMUMS 1.16.2 MAXDEM T2 C1-CUR
MAXIMUMS 1.16.3 MAXDEM T3 C1-CUR
MAXIMUMS 1.16.4 MAXDEM T4 C1-CUR
MAXIMUMS 1.16.5 MAXDEM T4 C1-CUR
MAXIMUMS 1.16.6 MAXDEM T6 C1-CUR
MAXIMUMS 1.16.0 MAXDEM TOTAL
C1-CUR
Maximums from the bill closure
(if active), included in the total
1.16.x where x = tariff
( eriod)
4.4.1.1.2. Screen L12 (CONTRACT 1 :CLOSURE 01)
Shows information on the values for contract 1 from the last closure. The screen acts
in the same way as the L11 screen, using Absolute or Incremental values.
Inc (Incrementales)
OBIS SIN OBIS
KWH 1.19.1.01 INCIMP T1 C1-b01
KWH 1.19.2.01 INCIMP T2 C1-b01
KWH 1.19.3.01 INCIMP T3 C1-b01
KWH 1.19.4.01 INCIMP T4 C1-b01
KWH 1.19.5.01 INCIMP T5 C1-b01
KWH
1.19.6.01 INCIMP T6 C1-b01
Consumo or eríodos
tarifarios de Energía
Activa del último eríodo
de facturación (si están
activos),incluido el total
( eríodo 0)
KWH 1.19.0.01 INCIMP TOTAL C1-b01 1.19.x.01
donde x = tarifa ( eríodo)
KVARL 1.59.1.01 INCQ1 T1 C1-b01
KVARL 1.59.2.01 INCQ1 T2 C1-b01
KVARL 1.59.3.01 INCQ1 T3 C1-b01
KVARL 1.59.4.01 INCQ1 T4 C1-b01
KVARL 1.59.5.01 INCQ1 T5 C1-b01
KVARL 1.59.6.01 INCQ1 T6 C1- b01
KVARL 1.59.0.01 INCQ1 TOTAL
C1-b01
Consumo or eríodos
tarifarios de Energía
Reactiva Q1 del último
eríodo de facturación (si
están activos),incluido el
total ( eríodo 0)
1.59.x.01 donde x =
tarifa ( eríodo)
Power Excesses 1.12.1.01 EXCES T1 C1-b01
Power Excesses 1.12.2.01 EXCES T2 C1-b01
Power Excesses 1.12.3.01 EXCES T3 C1-b01
Power Excesses 1.12.4.01 EXCES T4 C1-b01
Power Excesses 1.12.5.01 EXCES T5 C1-b01
Power Excesses 1.12.6.01 EXCES T6 C1-b01
Excesos del último
eríodo de facturación (si
están activos)
1.12.x.01 donde x =
tarifa ( eríodo)
MAXIMUMS 1.16.1.01 MAXDEM T1 C1-b01
MAXIMUMS 1.16.2.01 MAXDEM T2 C1-b01
MAXIMUMS 1.16.3.01 MAXDEM T3 C1-b01
MAXIMUMS 1.16.4.01 MAXDEM T4 C1-b01
MAXIMUMS 1.16.5.01 MAXDEM T4 C1-b01
MAXIMUMS 1.16.6.01 MAXDEM T6 C1-b01
L12
MAXIMUMS 1.16.0.01 MAXDEM TOTALC1-b01
Máximas del último
eríodo de facturación (si
están activas), incluido el
total ( eríodo 0)
1.16.x.01 donde x =
tarifa ( eríodo)

Page No. 11
The codes for the incremental value variables are shown below:
Inc (Incremental)
OBIS Whio t OBIS
KWH 1.19.1.01 INCIMP T1 C1-b01
KWH 1.19.2.01 INCIMP T2 C1- b01
KWH 1.19.3.01 INCIMP T3 C1-b01
KWH 1.19.4.01 INCIMP T4 C1-b01
KWH 1.19.5.01 INCIMP T5 C1-b01
KWH
1.19.6.01
I
INCIMP T6 C1-b01
Consum tion er Active
Energy tariff eriods from
the last billing eriod (if
active), included in the
total ( eriod 0
1.19.x.01 where x = tariff
( eriod)
KWH 1.19.0.01 INCIMP TOTAL C1-b01
KVARL 1.59.1.01 INCQ1 T1 C1-b01
KVARL 1.59.2.01 INCQ1 T2 C1-b01
KVARL 1.59.3.01 INCQ1 T3 C1-b01
KVARL 1.59.4.01 INCQ1 T4 C1-b01
KVARL 1.59.5.01 INCQ1 T5 C1-b01
KVARL 1.59.6.01 INCQ1 T6 C1-b01
KVARL 1.59.0.01 INCQ1 TOTAL
C1-b01
Consum tion er Q1
Reactive Energy tariff
eriods from the last billing
eriod (if active), included
in the total ( eriod 0)
1.59.x.01 where x = tariff
( eriod)
Power Excesses 1.12.1.01 EXCES T1 C1-b01
Power Excesses 1.12.2.01 EXCES T2 C1-b01
Power Excesses 1.12.3.01 EXCES T3 C1-b01
Power Excesses 1.12.4.01 EXCES T4 C1-b01
Power Excesses 1.12.5.01 EXCES T5 C1-b01
Power Excesses 1.12.6.01 EXCES T6 C1-b01
Excesses from last billing
eriod (if active)
1.12.x.01 where x = tariff
( eriod)
MAXIMUMS 1.16.1.01 MAXDEM T1 C1-b01
MAXIMUMS 1.16.2.01 MAXDEM T2 C1-b01
MAXIMUMS 1.16.3.01 MAXDEM T3 C1-b01
MAXIMUMS 1.16.4.01 MAXDEM T4 C1-b01
MAXIMUMS 1.16.5.01 MAXDEM T4 C1-b01
MAXIMUMS 1.16.6.01 MAXDEM T6 C1-b01
L12
MAXIMUMS 1.16.0.01 MAXDEM TOTALC1-b01
Maximums form last billing
eriod (if active) included
in the total ( eriod0)
1.16.x.01 where x =
tariff ( eriod)
4.4.1.1.3. Screen L13 (CONTRACT 1: CLOSURE 02)
Shows information on the values for contract 1 from the enultimate closure. The
screen acts the same as for L12..
The information is dis layed in exactly the same way as in screen L12, but field F will
have the value 02 instead of 01.
Fox exam le: 1.18.1.02  Absolute active energy consumed, from eriod 1,
enultimate bill closure.

Page No. 12
4.4.1.1.4. Screen L14 (CONTRACT 1: CLOSURE 03)
Shows information on the values for contract 1 from the ante enultimate closure. The
screen acts the same as for L12..
The information is dis layed in exactly the same way as in screen L12, but field F will
have the value 03 instead of 01.
Fox exam le: 1.18.1.03  Absolute active energy consumed, from eriod 1, bill
closure 3.
4.4.1.1.5. Screen L15 (CONTRACT 1: CLOSURE 04)
Shows information on the values for contract 1 from closure 04. The screen acts the
same as for L12..
The information is dis layed in exactly the same way as in screen L12, but field F will
have the value 04 instead of 01.
Fox exam le: 1.18.1.04  Absolute active energy consumed, from eriod 1, bill
closure 4
4.4.1.1.6. Screen L16 (CONTRACT 1: CLOSURE 05)
Shows information on the values for contract 1 from closure 05. The screen acts the
same as for L12..
The information is dis layed in exactly the same way as in screen L12, but field F will
have the value 05 instead of 01.
Fox exam le: 1.18.1.05  Absolute active energy consumed, from eriod 1, bill
closure 5.
4.4.1.1.7. Screen L17 (CONTRACT 1) CLOSURE 06)
Shows information on the values for contract 1 from closure 06. The screen acts the
same as for L12..
The information is dis layed in exactly the same way as in screen L12, but field F will
have the value 06 instead of 01.
Fox exam le: 1.18.1.06  Absolute active energy consumed, from eriod 1, bill
closure 6.
4.4.1.2.- Screen L2 (CONTRACT 2)
This screen accesses information on contract 2. It acts in the same way as L1.
All data screens that de end on this screen have the value 2 in grou B of the code.
4.4.1.2.1. Screen L21 (CONTRACT 2: CURRENT)
This shows information on the current values for contract 2. It acts in the same way
as screen L11, but changes the grou B code from 1 to 2. The information is dis layed in
exactly the same way as in screen L11, exce t for Power Excesses, which will not a ear
Data is dis layed with zeros to the left to fill u the length of the dis lay.
Fox exam le: 2.16.2  Absolute, current maximum demand for eriod 2 and for
contract 2.

Page No. 13
4.4.1.2.2. Screen L22 (CONTRACT 2: CLOSURE 01)
This shows information on the current values for contract 2. It acts in the same way
as screen L12, but changes the grou B code from 1 to 2. The information is dis layed in
exactly the same way as in screen L11, exce t for Power Excesses, which will not a ear
Data is dis layed with zeros to the left to fill u the length of the data field dis lay
For exam le: 2.18.2.01  Absolute active energy consumed, from eriod 2,
enultimate bill closure from contract 2.
4.4.1.2.3. Screen L23, L24, L25, L26, L27 (CONTRACT 2: CLOSURES 02
TO 06)
Shows information on the values for contract 2 from the closures rior to the last closure. It
acts in the same way as screens L13-L17, but the grou B code changes from 1 to 2.
4.4.1.3.- Screen L3 (CONTRACT 3)
This screen accesses information on contract 3. It acts in the same way as screen L1,
4.4.1.3.1. Screen L31-L37 (CONTRACT 3: CURRENT AND CLOSURES 01
TO 06)
Import direction.
This shows information on the current values for contract 3. It acts in the same way
as screen L11, but the grou B code changes from 1 to 3.
As contract 3 is valid for both the urchase and sale of energy, the data codes will
de end on the contract being set for one or other energy direction This is a licable both for
current values and for all the closures.
Export direction
This shows information on the current values for contract 3. It acts in the same way
as screen L11, but the grou B code changes from 1 to 3.
AbS (Absol te)
OBIS SIN OBIS
KWH 3.28.1 ABSEXP T1 C3-CUR
KWH 3.28.2 ABSEXP T2 C3-CUR
KWH 3.28.3 ABSEXP T3 C3-CUR
KWH 3.28.4 ABSEXP T4 C3-CUR
KWH 3.28.5 ABSEXP T5 C3-CUR
KWH 3.28.6 ABSEXP T6 C3-CUR
KWH 3.28.0 ABSEXP TOTAL C3-
CUR
Tariff eriods for Active Energy
from the start of measurement
(if active), included in the total
3.28.x where x = tariff
( eriod)
KVARL 3.68.1 ABSQ2 T1 C3-CUR
KVARL 3.68.2 ABSQ2 T2 C3-CUR
KVARL 3.68.3 ABSQ2 T3 C3-CUR
KVARL 3.68.4 ABSQ2 T4 C3-CUR
KVARL 3.68.5 ABSQ2 T5 C3-CUR
KVARL 3.68.6 ABSQ2 T6 C3-CUR
KVARL 3.68.0 ABSQ2 TOTAL C3-
CUR
Tariff eriods for Q2 Reactive
Energy from the start of
measurement (if active),
included in the total
3.68.x where x = tariff
( eriod)
Power Excesses
3.22.1 EXCES T1 C3-CUR
Power Excesses
3.22.2 EXCES T2 C3-CUR
L31-
L37
Power Excesses
3.22.3 EXCES T3 C3-CUR
Excesses from the last bill
closure(if active)
3.22.x

Page No. 14
Power Excesses
3.22.4 EXCES T4 C3-CUR
Power Excesses
3.22.5 EXCES T5 C3-CUR
Power Excesses
3.22.6 EXCES T6 C3-CUR
where x = tariff ( eriod)
MAXIMUMS 3.26.1 MAXDEM T1 C3-CUR
MAXIMUMS 3.26.2 MAXDEM T2 C3-CUR
MAXIMUMS 3.26.3 MAXDEM T3 C3-CUR
MAXIMUMS 3.26.4 MAXDEM T4 C3-CUR
MAXIMUMS 3.26.5 MAXDEM T5 C3-CUR
MAXIMUMS 3.26.6 MAXDEM T6 C3- CUR
MAXIMUMS 3.26.0 MAXDEM TOTAL C3-
CUR
Maximums from the bill closure
(if active), included in the total
3.26.x where x = tariff
( eriod)
The codes for the incremental value variables are shown below:
Inc (Incremental)
OBIS SIN OBIS
KWH 3.29.1 ABSEXP T1 C3-CUR
KWH 3.29.2 ABSEXP T2 C3-CUR
KWH 3.29.3 ABSEXP T3 C3-CUR
KWH 3.29.4 ABSEXP T4 C3-CUR
KWH 3.29.5 ABSEXP T5 C3-CUR
KWH 3.29.6 ABSEXP T6 C3-CUR
KWH 3.29.0 ABSEXP TOTAL C3-CUR
Consum tion er Active
Energy tariff eriods from the
last billing eriod (if active),
included in the total
3.29.x.01 where x = tariff
( eriod)
KVARL 3.69.1 ABSQ2 T1 C3-CUR
KVARL 3.69.2 ABSQ2 T2 C3-CUR
KVARL 3.69.3 ABSQ2 T3 C3-CUR
KVARL 3.69.4 ABSQ2 T4 C3-CUR
KVARL 3.69.5 ABSQ2 T5 C3-CUR
KVARL 3.69.6 ABSQ2 T6 C3-CUR
KVARL 3.69.0 ABSQ2 TOTAL C3-CUR
Consum tion er Q2 Reactive
Energy tariff eriods from the
last billing eriod (if active),
included in the total
3.69.x.01 where x = tariff
( eriod)
Excesos Potencia 3.22.1 EXCES T1 C3-CUR
Excesos Potencia 3.22.2 EXCES T2 C3-CUR
Excesos Potencia 3.22.3 EXCES T3 C3-CUR
Excesos Potencia 3.22.4 EXCES T4 C3-CUR
Excesos Potencia 3.22.5 EXCES T5 C3-CUR
Excesos Potencia 3.22.6 EXCES T6 C3-CUR
Excesses from the last bill
closure(if active)
3.22.x
where x = tariff ( eriod)
MAXIMAS 3.26.1 MAXDEM T1 C3-CUR
MAXIMAS 3.26.2 MAXDEM T2 C3-CUR
MAXIMAS 3.26.3 MAXDEM T3 C3-CUR
MAXIMAS 3.26.4 MAXDEM T4 C3-CUR
MAXIMAS 3.26.5 MAXDEM T5 C3-CUR
MAXIMAS 3.26.6 MAXDEM T6 C3- CUR
L31-
L37
MAXIMAS 3.26.0 MAXDEM TOTAL C3-CUR
Maximums from the last billing
eriod (if active ) included in
the total
3.26.x.01 where x = tariff
( eriod)

Page No. 15
4.4.1.4.- Screen L4 (INFORMATION)
This screen accesses information not relevant to the contract billing values. It is a
MENU screen. It accesses other de endent MENU screens as shown below:
Screens Text Comments
L40 OPERATIONAL
INDICATORS
To check the ro er working of the equi ment in all it’s
basic as ects during installation and for subsequent in
situ checks
L41 POWER
CONTRACTS
This is used to indicate the values of the contracted
owers. It only a lies to ower excesses in Contract 1
L42 TRANSFORMATION
RATIOS This shows information on transformation ratios
L43 CURRENT VALUES
Shows information on current ower, maximum, totals
and ower form the last integration eriod (As a default:
15 minutes)
L44 INSTANT VALUES This shows information on the instant values of different
electrical magnitudes
L45 COMMUNICATIONS This shows information on the different arameters of the
communications orts
L46 IDENTIFIERS This shows information on the equi ment's different
identifiers, included those for the IEC870-5-102 rotocol
L47 OUTPUT
CONSTANTS This shows information on the out ut im ulse values
L48 TIME CHANGE This shows information on the dates of the time change.
L49 BACK Returns to the revious screen
4.4.1.4.1. Screen L40 (INFORMATION: INDICATORS)
This screen shows information on the o erating indicators. These are used to check
the ro er working of the equi ment in all its basic as ects during installation and for
subsequent in situ checks. It is a DATA screen
As these indicators do not corres ond to a s ecific contract, but is data general to all,
field B takes the value 0.
Code
Screen Text OBIS Sin OBIS Comments
0.13.38
.ej. 1 .ACT.Q
ACTIVE QUADRANT: This indicates the
direction of the active or reactive energy or
quadrant (1,2,3 or 4)
0.12.38
.ej. 123
PRES.V
PRESENCE OF VOLTAGE: Indicates the
resence of voltage in each hase (123 if
there is voltage in all, blank if there is no
voltage)
0.11.38
.ej. 120
C.DIR
CURRENT DIRECTION: This indicates the
direction of im ortation (+) or ex ortation (-
) in each hase (111 if they are im orted,
222 if ex orted, 000 if there is none)
L40 INDICATORS
0.18.128
.ej. 633
TAR.AC
ACTIVE TARIFF FOR EACH CONTRACT:
This indicates the active tariff at the time of
reading for each contract (contract 1,
contract 2, contract 3)(values form 1 to 6
for each contract)

Page No. 16
0.96.2.4
.ej. 0 P.MODE
PARAMETERISATION MODE: This
indicates if the arameterisation mode is
enabled (0 disabled, 1 enabled)
0.96.5.0
.ej. cnb
ALARM
ALARMS: This indicates the alarms
defined in section 4.3. The data field will
dis lay the letters cnb, which will become
active according to the ty e of alarm.
4.4.1.4.2. Screen L41 (INFORMATION: CONTRACT PARAMETERS)
This screen shows information on the contracted owers for contract 1. It only a lies
to ower excesses in Contract 1. It is a DATA screen
Code
Screen Text OBIS Whito t OBIS
Comments
1.135.1 C1 T1
1.135.2 C1 T2
1.135.3 C1 T3
1.135.4 C1 T4
1.135.5 C1 T5
L41
CONTRACT
POWERS
1.135.6 C1 T6
CONTRACTED POWERS: This is for
the values of the contracted owers in
kW to 2 decimals that will be used to
calculate excesses
1,135.x where x = tariff ( eriod)
4.4.1.4.3. Screen L42 (INFORMATION: TRANSFORMATION RATIOS)
This screen shows information on the transformation ratios. As this data does not
corres ond to any s ecific contract but is data general to all, field B will have the value 0. It is
a DATA screen
Code
Screen Text OBIS
Whito t
OBIS
Comments
0.04.2
I PRI
CURRENT RATIO PRIMARY : This
shows the current ratio rimary to 1
decimal
0.04.5
I SEC
CURRENT RATIO SECONDARY:
This shows the current ratio
secondary to 1 decimal
0.04.3
V PRI
VOLTAGE RATIO PRIMARY : This
shows the voltage ratio rimary to 1
decimal (com ound voltage)
L42 TRANSFORMATION
RATIOS
0.04.6
V SEC
VOLTAGE RATIO SECONDARY :
This shows the voltage ratio
secondary to 1 decimal (com ound
voltage)

Page No. 17
4.4.1.4.4. Screen L43 (INFORMATION: CURRENT VALUES)
This screen shows information on current values ower, maximum, totals and ower
from the last integration eriod (As a default 15 minutes). As this data does not corres ond to
any s ecific contract but is data general to all, field B will have the value 0. It is a DATA
screen
Code
Screen Text OBIS Whito t
OBIS
Comments
0.18.0 IMP TOTAL A+: This shows the current total for
Active Energy taken from the system
0.28.0 EXP TOTAL A-: This shows the current total for
Active Energy taken from the system
0.58.0 Q1 TOTAL R1: This shows the current total for
Reactive Energy in Quadrant 1
0.68.0 Q2 TOTAL R2: This shows the current total for
Reactive Energy in Quadrant 2
0.78.0 Q3 TOTAL R3: This shows the current total for
Reactive Energy in Quadrant 3
0.88.0 Q3 TOTAL R4: This shows the current total for
Reactive Energy in Quadrant 4
0.14.0 MDP+
CURRENT INPUT POWER: This shows the
average in ut ower that is being integrated
during the current integration eriod
0.24.0 MDP-
CURRENT OUTPUT POWER: This shows
the average out ut ower that is being
integrated during the current integration
eriod
0.15.0 TMDP+
LAST PERIOD INPUT POWER: This shows
the average in ut ower that is being
integrated during the last integration eriod
L43 0.
CURRENT
0.25.0 TMDP-
LAST PERIOD OUTPUT POWER: This
shows the average out ut ower that is
being integrated during the last integration
eriod

Page No. 18
4.4.1.4.5. Screen L44 (INFORMATION: INSTANT VALUES)
This screen shows information on the instant values of different electrical magnitudes.
As this data does not corres ond to any s ecific contract but is data general to all, field B will
have the value 0.
Code
Screen
Text OBIS Whito t
OBIS
Comments
0.327.0
V1 VOL
0.527.0
V2 VOL
0.727.0
V3 VOL
VOLTAGE PER PHASE: This shows the instant
current values in each hase.
0.317.0
I1 AMP
0.517.0
I2 AMP
0.717.0
I3 AMP
CURRENT PER PHASE: This shows the instant
Current values in each hase.
0.337.0
COSFI 1
0.537.0
COSFI 2
0.737.0
COSFI 3
COS Φ PER PHASE: This shows the instant cos Φ
values in each hase.
0.17.0 P kW
INSTANT ACTIVE POWER: This shows the total
instant Active Power in each of the three hases
with its sign.
0.37.0 Q kvar.
INSTANT REACTIVE POWER: This shows the
total instant Reactive Power in each of the three
hases with its sign.
L44 NSTANT
0.137.0
FP 3PH AVERAGE POWER FACTOR: This shows the
average instant Power Factor in the three hases.
4.4.1.4.6. Screen L45 (INFORMATION: COMMUNICATIONS)
This screen shows information on the different arameters of the communications
orts. As this data does not corres ond to any s ecific contract but is data general to all, field
B will have the value 0.
Code
Screen Text OBIS Whito t
OBIS
Comments
0.00.0
OPTIC OPTICAL SERIES PORT SETTING:
000000n (009600 s eed, n arity)
0.00.1
R1
ELECTRICAL SERIES PORT
SETTING 1: 000000n (009600 s eed,
n arity)
0.00.2
R2
ELECTRICAL SERIES PORT
SETTING 2: 000000n (009600 s eed,
n arity)
L45 COMMUNICATIONS
0.00.3
MODEM
ELECTRICAL SERIES PORT 1
MODEM START UP MODE : It will
a ear as data for the ASDU 142 of
the rotocol

Page No. 19
4.4.1.4.7. Screen L46 (INFORMATION: IDENTIFIERS)
This screen shows information on the equi ment's different identifiers, including those
for the IEC870 rotocol. As this data does not corres ond to any s ecific contract but is data
general to all, field B will have the value 0.
Code
Screen Text OBIS Whito t
OBIS
Comments
0.00.5
REG.AD LINK ADDRESS
0.00.6
MP.ADD MEASUREMENT POINT ADDRESS
0.00.7
PROTOC
DATE OF THE COMMUNICATIONS
PROTOCOL VERSION: (DD-MM-
YY), data from the ASDU 142 of the
rotocol will be shown
0.02.0
FIRMW
EQUIPMENT'S FIRMWARE
VERSION: data from the ASDU 142
of the rotocol will be shown
0.08.4
INTGP1
INTEGRATION PERIOD OF THE
FIRST LOAD CURVE: this shows the
integration eriod in minutes, 60
minutes as a default.
L46 IDENTIFIERS
0.08.5
INTGP2
INTEGRATION PERIOD OF THE
SECOND LOAD CURVE: this shows
the integration eriod of the second
load curve in minutes, 15 minutes as
a default.
4.4.1.4.8. Screen L47 (INFORMATION: OUTPUT CONSTANTS)
This screen shows information on the im ulse values of the out uts. As this data
does not corres ond to any s ecific contract but is data general to all, field B will have the
value 0.
Code
Screen Text OBIS Whito t
OBIS
Comments
0.03.3 OUT . 1 OUTPUT 1
0.03.4 OUT . 2 OUTPUT 2
0.03.5 OUT . 3 OUTPUT 3
L47 OUTPUT
CONSTANTS
0.03.6 OUT . 4 OUTPUT 4
O tions for each ty e of out ut are:
Ax Y:
x = 1:im orted active / x= 2: ex orted active / Y = im ulse weight
Rx Y:
x = quadrant no. (reactive quadrant x) / Y = im ulse weight
Pow : Power demand meter
C x P y:
x = Contract No. / and = tariff eriod no. (the out ut indicates the tariff)