CIS VCC-FC20V49CL Quick start guide

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
29mm cubic VGA
High-Speed Color CMOS Camera
VCC-FC20V49CL
Product Specification
& Operational Manual
CIS Corporation
En
g
lish

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
2
Table of Contents
PAGE
1. Scope of Application..................................................................................................................................................3
2. Handling Precautions.................................................................................................................................................3
3. Notes on Partial Scan Mode Operation........................................................................................................................5
4. Product Outline.........................................................................................................................................................5
5. Specification.............................................................................................................................................................6
5.1. General Specification.....................................................................................................................................6
5.2. Camera Output Signal Specification................................................................................................................8
5.3. CMOS Spectral Response (Representative value) .............................................................................................9
5.4. Video Output Format .....................................................................................................................................9
5.5. Camera Link Port Data Bit Assignment (Base Configuration)...........................................................................10
6. Function Settings ....................................................................................................................................................11
7. External Connector Pin Assignment ...........................................................................................................................13
7.1. 6pins Circular Connector HR10-7R-6PA (HIROSE) equivalent........................................................................13
7.2. 26pins Mini Camera Link Connector 12226-1100-00 PL (SUMITOMO 3M).....................................................13
8. Timing Chart...........................................................................................................................................................14
8.1. Horizontal Synchronous Signal Timing...........................................................................................................14
8.2. Vertical Synchronous Signal Timing...............................................................................................................14
8.2.1 Full Frame Scan Mode..................................................................................................................................14
8.2.2 Fixed Trigger Shutter Mode ..........................................................................................................................15
8.2.3 Pulse Width Trigger Shutter Mode.................................................................................................................16
9. Partial Scan Mode....................................................................................................................................................17
10. Remote Interface Function...................................................................................................................................18
11. Initial Settings.....................................................................................................................................................19
12. CMOS Optical Axis Accuracy..............................................................................................................................20
13. Dimensions.........................................................................................................................................................21
14. Cases for Indemnity (Limited Warranty)................................................................................................................22
15. Sensor Pixel Defect..............................................................................................................................................22
16. Product Support..................................................................................................................................................22

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
3
1. Scope of Application
This is to describe VCC-FC20V49CL, high-speed Color CMOS Camera. All specifications contained herein
are subject to change without prior notice. Reproduction in whole or in part is prohibited.
2. Handling Precautions
The camera must not be used for any nuclear equipments or aerospace equipments with which
mechanical failure or malfunction could result in serious bodily injury or loss of human life. Our
warranty does not apply to damages or defects caused by irregular and/or abnormal use of the product.
Please observe all warnings and cautions stated below.
Our warranty does not apply to damages or malfunctions caused by neglecting these precautions.
zDo not use or store the camera in the following extreme conditions:
¾Extremely dusty or humid places.
¾Extremely hot or cold places (operating temperature –5 to +45 )℃℃
¾Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.
¾Places subject to fluorescent light reflections.
¾Places subject to unstable (flickering, etc.) lighting conditions.
¾Places subject to strong vibration.
zRemove dust or dirt on the surface of the lens with a blower.
zDo not apply excessive force or static electricity that could damage the camera.
zDo not shoot direct images that are extremely bright (e.g., light source, sun, etc.), and when camera
is not in use, put the lens cap on.
zFollow the instructions typeapter 7, “External connector pin assignment” for connecting the camera.
Improper connection may cause damages not only to the camera but also to the connected devices.
zConfirm the mutual ground potential carefully and then connect the camera to monitors or
computers. AC leaks from the connected devices may cause damages or destroy the camera.
zDo not apply excessive voltage. (Use only the specified voltage.) Unstable or improper power supply
voltage may cause damages or malfunction of the camera.

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
4
zThe voltage ripple of camera power DC +12V±10% shall be within ±50mV. Improper power
supply voltage may cause noises on the video signals.
zThe rising time of camera power supply voltage shall be less than +10V, Max 60ms.
Please avoid noises like chattering when rising.
In case of abnormal operation, contact the distributor from whom you purchased the product.
10 4020 30 50
10
11
12
[V]
Voltage Rising Time [ms]
9
8
7
60 70
Power Supply Voltage

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
5
3. Notes on Partial Scan Mode Operation
At vertical partial scan mode, the smaller the set reading out lines, the faster the camera exposure and
output operation will be. And, at the same time, power consumption will be increased.
Power consumption when the minimum partial scan line number is set will be approx. 2.4W, while it will be
approx. 1.6W at full frame scan. That is about 1.5 times higher. With higher power consumption, heat
will be increased as well.
We recommend promoting heat dissipation when installing our camera to your system, especially when
reading out line is set between the ranges of 50lines to 1line.
For instance, installing the camera to the place under 40 degrees C ambient temperature, or installing the
camera to a metalic part, would be effective.
4. Product Outline
VCC-FC20V49CL is an industrial Color high-speed digital video camera module utilizing a global shutter type,
CMOS sensor. Interface of FC20V49CL complies with camera link (Base Configuration) with its resolution
300K pixels. Clipping part of the image for VGA 1/4 type size, entire pixels can be read out within approx.
1/500s.
Key Features
□ High frame rate, 502.29 fps, at full frame scan mode with Camera Link Base Configuration.
Frame rate = (pixel clock) / (((horizontal output pixels/output tap number)
+ Horizontal Blanking) × (Vertical Output Lines + Vertical Blanking))
= (79.99MHｚ) / (((640/2) +5)×(480+10))
= 502.29fps
□ 29mm cubic in size (excluding projection).
□ Camera Link 2Tap output (Base Configuration)
□ RAW data output 8bit / 10bit selectable
□ External Trigger
□ Shutter Speed: 1/500s ～1/50,000s
□ Fixed Trigger Shutter Mode
□ Pulse Width Trigger Shutter Mode
□ Partial Scan Mode (Vertical)
□ Free sample control software for evaluation purpose only is downloadable via our web.

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
6
5. Specification
5.1. General Specification
Item Specification
(1) Pickup Device
Device Type Color CMOS
Effective Pixel Number 640(H) ×480(V)
Unit Cell Size 5.50μm(H) ×5.50μm(V)
Chip Size 3.52mm(H) ×2.64mm(V) (640×5.5μm(H) ×480×5.5μm(V)
Image Circle φ4.4mm
(2) Video output frequency
Pixel Clock 79.99 MHz
Horizontal Frequency 246.12kHz Pixel Clock: 325CLK
Vertical Frequency Full Frame Scan Mode: 502.29Hz Scanning Lines: 490H
Partial Scan Mode
(Vertical 1/2): 984.49Hz Scanning Lines: 250H
(3) Sync. system Internal Sync. System
(4) Video output standard Camera Link 2Tap Output (Base Configuration)
(5) Resolution 480 TV lines equivalent (VGA size)
(6) Output Format RAW data output 8bit/10bit selectable
(7) Sensitivity F2.0 2000lx (Shutter Speed: 1/500s, Gain 0dB)
(8) Minimum illumination F1.4 150lx (Shutter Speed: 1/500s, Gain +12dB)
(9) Dust or stains in
optical system No dust or stain shall be detected on the testing screen with setting the camera aperture at F16.
(10) Power requirements DC+12V±10% (Max voltage shall not be exceeded +15V.)
(11) Power consumption Approx. 1.6W at ful frame scan (DC+12V IN).
Approx. 2.4W at partial scan with minimum line number setting (DC DC+12V IN).
(12) Dimension Refer to overall dimension drawing (Clause 12)
H:29mm W:29mm D:29mm (excluding projection)
(13) Mass Approx. 50g
(14) Lens mount C mount (Refer to overall dimension drawing)
(15) Optical axis accuracy Refer to drawing for CMOS Optical Axis Accuracy (Clause 11)
(16) Gain variable range 0～+12dB (Digital Gain:+0.1dB/step)
(17) White balance
adjustment range 2800K～9000K(Manual White Balance )(Guaranteed range)
(18) Gamma 1(Fixed)
(19) Shutter speed
variable range OFF(1/500),1/750s,1/1000s,1/1500s,1/2000s,1/2500s,1/4000s,1/5000s,1/10000s,1/15000s,
1/20000s,1/25000s,1/30000s,1/40000s,1/50000s
(20) Trigger shutter mode ・Fixed Trigger Shutter Mode
・Pulse Width Trigger Shutter Mode (Exposure time is set with the pulse width of trigger signal.)
4.40
3.52
2.64
(Unit: mm)

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
7
Item Specification
(21) Safety/Quality standards
UL: Conform to UL Standard including materials and others.
CE: Conform to EN55022: 2006 (Class B) for Emmission
Conform to EN61000-6-2: 2005 for Immunity
RoHS: Conform to RoHS
FCC:
To be applied for FCC Class A Digital Device
This device complies with Part 15 of FCC Rules. Operation is subject to the
followiong two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
(22) Durability Vibration
Acceleration : 98m/s2 (10G)
Frequency : 20～200 Hz
Direction : X,Y,Z 3 directions
Testing time : 120 min for each direction
Shock No malfunction shall be occurred with 980m/s2(100G) for ±X, ±Y, and ±Z, 6
directions. (without package)
(23) Operation environment Temperature Operation guaranteed: -5℃～+45℃
Performance guaranteed: 0℃～+40℃
Humidity RH 20～80% with no condensation
(24) Storage environment Temperature -25℃～+60℃
Humidity RH 20～80% with no condensation

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
8
47pF
VD,HD
Exposure Output
+5.0V(VCC)
Trigger Input
HD74LV1GT32ACME
1KΩ
100Ω
470pF
(RENESAS)
Voh 3.8V (Min)
Vol 0.55V (Max)
HD74LV1GT14 ACME
(RENESAS)
Vih 2.0V (Min)
Vil 0.8V (Max)
100Ω
5.2. Camera Output Signal Specification
Item Specification
(1) Video output data Video Output 640 (H) ×480(V) At Full Frame Scan Mode
(2) Sync. Signal I/O
LVAL output LVDS Camera Link connector
FVAL output LVDS
DVAL output LVDS
SP(Exposure) LVDS
HD output LVTTL 6pins Circular connector
VD output LVTTL
Exposure LVTTL
(3) Trigger input
Polarity POSI/NEGA Selectable
Min width of trigger pulse 10μs
Camera Link input LVDS : CC1 input Camera Link connector
TTL input LVTTL: No.2 pin 6pins Circular connector
VIH Min. 2.0V
VIL Max. 0.8V
(4) Serial
Communication SerTC (Serial to Camera) Camera Link input (LVDS)
SerTFG (Serial to Frame Grabber) Camera Link output (LVDS)
(5) Video output signal
White Clip Level Digital 8bit :FFh
Setup Level Digital 8bit :00h
Dark Shading Digital 8bit :under ±04h for both vertical and horizontal.
(condition: gain 0dB)
5 seconds shall be waited after turning on power to get proper camera operation.
6pins Circular Connector at rear: GPIO interface

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
9
5.3. CMOS Spectral Response (Representative value)
※Lens characteristics and illuminant characteristics are not considered.
5.4. Video Output Format
VGA 500fps Mode: 2Tap Interleaved
Bayer Pattern: GBRG (At full frame scan)
* At manual partial scan mode, Bayer Pattern changes per 1 line according to the set vertical starting position
value.
DA0
(G)
DB0
(B)
~ ~
From Camera
(2 Tap Output)
~
~
DA0
DA1
DA2
DB0 DB1 DB2
DA1
(G)
DB1
(B)
DA2
(G)
DB2
(B)
DA0
(R)
DB0
(G)
Lines
Pixels
01234
0
1
2
1087
2047
DA1
(R)
DB1
(G)
DA2
(R)
DB2
(G)

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
10
5.5. Camera Link Port Data Bit Assignment (Base Configuration)
Port/bit At 8bit output setting At 10bit output setting
Port A0 DA:bit0[LSB] DA:bit0[LSB]
Port A1 DA:bit1 DA:bit1
Port A2 DA:bit2 DA:bit2
Port A3 DA:bit3 DA:bit3
Port A4 DA:bit4 DA:bit4
Port A5 DA:bit5 DA:bit5
Port A6 DA:bit6 DA:bit6
Port A7 DA:bit7[MSB] DA:bit7
Port B0 DB: bit0[LSB] DA:bit8
Port B1 DB: bit1 DA:bit9[MSB]
Port B2 DB:bit2 Not in use
Port B3 DB:bit3 Not in use
Port B4 DB:bit4 DB:bit8
Port B5 DB:bit5 DB:bit9[MSB]
Port B6 DB:bit6 Not in use
Port B7 DB:bit7[MSB] Not in use
Port C0 Not in use DB:bit0[LSB]
Port C1 Not in use DB:bit1
Port C2 Not in use DB:bit2
Port C3 Not in use DB:bit3
Port C4 Not in use DB:bit4
Port C5 Not in use DB:bit5
Port C6 Not in use DB:bit6
Port C7 Not in use DB:bit7

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
11
6. Function Settings
Camera functions can be set with serial data communications.
Function Address Data
Gain 001
0: 0 dB
1:
+
6 dB
2: + 12 dB
3: Manual Gain (Refer to address 008.)
4～255: 0dB
Shutter
(at full frame scan mode)
※For partial scan mode,
please refer to Section 9.
002
0: 1/500s
1: 1/500s
2: 1/750s
3: 1/1000s
4: 1/1500s
5: 1/2000s
6: 1/2500s
7: 1/4000s
8: 1/5000s
9: 1/10000s
10: 1/15000s
11: 1/20000s
12: 1/25000s
13: 1/30000s
14: 1/40000s
15: 1/50000s
16: Manual Shutter (Refer to address 009&010.)
17～255: 1/500s
White Balance 003
0: Through
1: 3200K
2: Spare
3: Spare
4: Manual White Balance (Refer to the Address 006&007.)
5～255: Through
Trigger Shutter Mode 004
0: Normal Shutter Mode (Trigger Shutter Mode OFF)
1: Fixed Trigger Shutter Mode
(Shutter speed can be set with address 002.)
2: Pulse Width Trigger Shutter Mode
(Shutter speed can be set with trigger pulse width.)
3～255: Normal Shutter Mode (Trigger Shutter Mode OFF)
Scan Mode 005
0: Full Frame Scan Mode
1: Partial Scan Mode (Vertical 1/2)
2: Manual Partial Scan Mode (Refer to address 016/017 & 019/020.)
3～255: Full Frame Scan Mode
Manual White Balance
R Gain Control 006 0～120: 0～+12dB 0.1dB/step ※Make the data of Address 003 to 004.
121～255: +12dB
Manual White Balance
B Gain Control 007 0～120: 0～+12dB 0.1dB/step ※Make the data of Address 003 to 004.
121～255: +12dB
Manual Gain Control 008 0～120: 0～+12dB 0.1dB/step ※Set the data of address 001 to 003.
121～255: +12dB

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
12
Function Address Data
Manual Shutter Control 009&010
0～480: 1/50000s～1/500s
481～2047: 480
※The setting will be 1 line when 0 is set.
Exposure Time = The set value × 1line Time [s]
1line Time [s] = ((output pixels/2tap)+5)×1/79.99MHz
At full frame scan, output pixels = 480
1lineTime ≒4.06μs
※Address 002 data shall be 016.
Address 009 MSB and Address 010 LSB make 11bit in total.
Trigger Polarity 011 0: Positive Input
1: Negative Input
2～255: Positive Input
Input Trigger Port Selection 012 0: Camera Link Connector 12226-1100-00 PL LVDS 1: 6pins Circular Connector TTL
2～255: Camera Link Connector: 12226-1100-00 PL
Output Data Selection 013 0: 8bit output data (RAW) 1: 10bit output data (RAW)
2～255: 8bit output data
Vertical Partial Scan
Start Position 016&017
0～Max. Value ※1line/step
※Max. value shall be limited according to the formula below.
480 (Vertical Partial Scan output max. lines – Vertical Partial Scan output lines)
※Address 005 data shalla be 002.
Address 016 MSB and Address 017 LSB make 11bit in total.
Vertical Partial Scan
Output Lines 019&020
0～480: 1line/step Min.:1line/Max :480 lines
481～2047: 480
※1 line shall be set when 0 is set.
Address 019 MSB and Address 020 LSB make 11bit in total.
※Address 005 data shalla be 002.
Remote Communication
Baud Rate Setting 030
0: 9600bps
1: 19200bps
2: 38400bps
3: 57600bps
4: 115200bps
5～255: 9600bps
Data Save 032 Input 083 to save address 000 ～031 to EEP-ROM.

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
13
7. External Connector Pin Assignment
7.1. 6pins Circular Connector HR10-7R-6PA (HIROSE)
equivalent
7.2. 26pins Mini Camera Link Connector 12226-1100-00 PL (SUMITOMO 3M)
Pin No.
1 Power IN DC+12V
2 Trigger IN(TTL level)
3 HD
4 VD
5 Exposure
6 GND
Pin No. Pin No.
1 GND 14 GND
2 X0- 15 X0+
3 X1- 16 X1+
4 X2- 17 X2+
5 Xclk- 18 Xclk+
6 X3- 19 X3+
7 SerTC+ 20 SerTC-
8 SerTFG- 21 SerTFG+
9 CC1- (Trigger IN-) 22 CC1+ (Trigger IN+)
10 CC2+ 23 CC2-
11 CC3- 24 CC3+
12 CC4+ 25 CC4-
13 GND 26 GND
123
4
5
6
1
13
14
26

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
14
LVAL Output
10 H
FVAL Output
DVAL Output
480 H
12 910
· · ·
11 12
Video Output · · · · · · ·
Exposure Time
2 H
· · · · · · ·
· · · · · · ·
1 H
479 48047847712
489 490488487
2 H2 H
Min. 1H ~ Max. 480 H
489 490488487
· · · · · · ·
490 H
LVAL Output
5CLK
Video Output
DVAL Output
1H = 325 CLK
320 CLK
CLK 79.99MHz
1
2
3
4
5
68
7633
634
635
636
637
638 640
639
・・・・・・・・・
5CLK 320 CLK
8. Timing Chart
8.1. Horizontal Synchronous Signal Timing
8.2. Vertical Synchronous Signal Timing
8.2.1 Full Frame Scan Mode
※Video output signal delays by 2H from Exposure Time.

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
15
LVAL Output
10 H
FVAL Output
DVAL Output
480 H
480 H
1211 491 49211 12
Video Output ・・・・・
Trigger Input
Exposure Time
Trigger Input
Exposure Time
Delay(Fixed)
330ns Exposure Time
(nHD ×4.06μs )
・・・・・
・・・・・
12
1 2 479 480
34
2 H
8.2.2 Fixed Trigger Shutter Mode
※Video output signal delays by 2H from Exposure Time.

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
16
LVAL Output
10 H
FVAL Output
DVAL Output
480 H
480 H
12 481 48213 14
Video Output ・・・・・
Trigger Input
Exposure Time
Trigger Input
Exposure Time
Delay(Fixed)
330ns
Exposure Time
・・・・・
・・・・・
Delay(Fixed)
270ns
3 4
2 H
12 479480
11 12
8.2.3 Pulse Width Trigger Shutter Mode
※Video output signal delays by 2H from Exposure Time.

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
17
LVAL Output
10 H
FVAL Output
DVAL Output
n H
· · ·
Video Output · · · · · · ·
Exposure Time
2 H
· · · · · · ·
· · · · · · ·
2 H n H (Max.)
Video Output
ss+1 s+n
-1 s+n
s+n
-2
s+n
-3
s+n
-1 s+n
s+n
-2
480
· · ·
FVAL Output
Partial scan (vertical 1/2) n: 240H
Manual partial scan n: any
· At full frame scan
· At vertical partial scan
· · ·· · ·
0 1 2 119 120 359 360 479478
2 H
Partial scan (vertical 1/2) s: 120H
Manual partial scan s: any
480
(The max vertical partial
scan output lines)
n = 400
The set vertical partial scan
output lines
0 ~ 80
Vertical partial scan
Starting position
Setting range
s = 90 (invalid)
vertical partial scan
starting position
Set value
s = 80 (with limitation)
vertical partial scan
starting position
0
80
90
479
9. Partial Scan Mode
・Vertical Partial Scan
s: Vertical partial scan starting position (address 016＆017)
n: Vertical partial scan output lines (address 019＆020)
Scan Mode (address:005) s n Vertical Sync. Frequency (Hz)
0:Full frame scan mode 0 480 502.29
1:Partial scan mode (Vertical 1/2) 120 240 984.49
2:Manual partial scan mode Any any 79.99MHz /((Vertical partial scan output lines +10)×(325))
・The max value of vertical partial scan starting position is limited with the formula below since vertical partial scan output
line has priority.
The max value of vertical partial scan starting position
=480(The max value of vertical partial scan output line) – Vertical partial scan output lines
(Ex.) When 400 is set as vertical partial scan output lines, the max value of vertical partial scan starting position will be
480-400 = 80.
If vertical partial scan starting position is set to 90 with this time, vertical partial scan output line has priority so that vertical
partial scan starting position shall be limited to 80.
※At manual partial scan mode, manual shutter value to be set shall meet the following conditions.
The set manual shutter lines ≦ Vertical partial scan output lines
If the condition above is not met, shutter lines to be set will be the same number as vertical partial scan output lines.

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
18
10. Remote Interface Function
Camera can be controlled by external computers and others via camera link interface.
(1)The settings for RS-232C are as follows.
Baud Rate : 9600bps,19200bps,38400bps,57600bps,115200bps
Data : 8bit
Stop bit : 1bit
Parity : None
XON/XOFF : not controlled
(2) Control code
・ The total control code is 14 bits, which conforms to ASCII code.
・ The control code consists of camera No. process code, remote controller address, remote
controller data, and CR. Execute Read/Write through PC, and the camera will reply the data.
1 2 3 4 5 6 7byte目8 9 10 11 12 13 14
Camera No. Process code Remote
controller
address
Remote controller
data CR
000000: Common No.
Dedicated Camera No.
“R” Read mode Please refer to
the address
table of 6.
Function
setting.
000～255
0Dh
“W” Write mode
“C”Camera
mode
Camera No
Please send the common code, “000000”, consist of 6 bytes of characters/numeric strings.
The returned data from the camera shall be the dedicated camera No assinged for that specific
camera.
Process code
Input any one of R, W, or C to the process code.
R (read mode) is to read the data of remote controller address.
Please be noted to set any dummy data (000～255) to 11th ～13th, since a command shall consists of
14 bytes.
W (write mode) is to write the data to the remote controller address.
Please be noted that the data cannot be saved into EEPROM of the camera.
(Reboot the camera, and the data is reset to the initial setting.)
To save the data into EEPROM, please refer to Clause 5.Function Setting.
Note: Once the data was saved into EEPROM, it may not be reset to t he initial settings.
C is the code to send the data back from the camera.
Note: Do not set code C when sending the data from PC side.

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
19
Remote controller address
Note: Do not save the data into the address other than specified, since it may cause the
damages or malfunction of the camera.
Remote controller data
Set the decimal number (000～255) for the remote controller data. Please be noted to set any
dummy data at read mode.
CR
Be sure to input “CR” to confirm the end of the command.
11. Initial Settings
Function Address Data
Gain 001 0: 0dB
Shutter 002 0: 1/500s
White Balance 003 0: Through
Trigger Mode 004 0: Normal Shutter Mode (Trigger Shutter Mode OFF)
Scan Mode 005 0: Full Frame Scan Mode
Manual White Balance
R Gain Control
006 0: 0dB
Manual White Balance
B Gain Control
007 0: 0dB
Manual Gain Control 008 0: 0dB
Manual Shutter Control 009&010 480: 1/500s
Trigger Polarity 011 0: Positive Input
Input Trigger Port Selection 012 0: Camera Link connector (12226-1100-00 PL)
Output Data Selection 013 0: 8bit Output Data (RAW)
Baud Rate 030 0:9600bps

VCC-FC20V49CL Rev.900-723-32-00
©2011 CIS Corporation. All rights reserved.
20
Inclination of optical axis to datum plane
2912
Datum
Plane
M2
M3
M2
29
29
The center of effective pixels shall be within f 0.6
to the center of C lens mount
Inclination of effective pixels, Theta,?, to datum plane shall be
?? ±0.5°
(*) Dimensions from datum plane to the center of the lens mount
910-006-01-01
Datum
Plane
Product Label Position ( ? )
(Unit:mm)
±0.2°
6±0.3
6±0.3
6±0.3
6±0.3
10±0.3
10±0.3
14.5±0.3(*)
±0.5°
12. CMOS Optical Axis Accuracy