CIS VISION:elite VCC-G60FV11CL Quick start guide

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
5M Pixel B/W Camera Link Camera
VCC-G60FV11CL
Product Specification
& Operational Manual
CIS Corporation
English

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
2
Table of Contents
1. Scope of Application.......................................................................................................................... 3
2. Handling Precautions ........................................................................................................................ 3
3. Product Outline................................................................................................................................. 4
4. Specification..................................................................................................................................... 5
4.1. General Specification .................................................................................................................. 5
4.2. Camera Output Signal Specification.............................................................................................. 7
4.3. CCD Spectral Response (Representative Value) ............................................................................. 9
5. Function Settings .............................................................................................................................10
6. External Connector Pin Assignment ...................................................................................................12
6.1. 12 pins Circular Connector HR10-10R-12PA (HIROSE) ..................................................................12
6.2. 26 pins Camera Link Connector 12226-1100-00 PL (SUMITOMO 3M) .............................................12
7. Timing Chart....................................................................................................................................13
7.1. Horizontal Synchronous Signals Timing........................................................................................13
7.2. Full Frame Scan Mode Timing .....................................................................................................13
7.3. Standard Trigger Mode Timing ....................................................................................................14
7.4. Pulse Width Trigger Timing .........................................................................................................14
8. Partial Scan Mode Details .................................................................................................................15
9. Remote Interface Function ...............................................................................................................15
10. Initial Settings ...............................................................................................................................17
11. CCD Optical Axis Accuracy ..............................................................................................................18
12. Dimensions....................................................................................................................................19
13. Cases for Indemnity (Limited Warranty)...........................................................................................20
14. CCD Pixel Defect............................................................................................................................20
15. Product Support.............................................................................................................................20

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
3
1. Scope of Application
This is to describe VCC-G60FV11CL, Camera Link B/W CCD Camera. All specifications contained herein are
subject to change without prior notice. Reproduction in whole or in part is prohibited.
2. Handling Precautions
The camera must not be used for any nuclear equipments or aerospace equipments with which mechanical
failure or malfunction could result in serious bodily injury or loss of human life. Our warranty does not apply
to damages or defects caused by irregular and/or abnormal use of the product.
Please observe all warnings and cautions stated below.
Our warranty does not apply to damages or malfunctions caused by neglecting these precautions.
Do not use or store the camera in the following extreme conditions:
Extremely dusty or humid places.
Extremely hot or cold places (operating temperature –5℃to +40℃)
Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.
Places subject to fluorescent light reflections.
Places subject to unstable (flickering, etc.) lighting conditions.
Places subject to strong vibration.
Remove dust or dirt on the surface of the lens with a blower.
Do not apply excessive force or static electricity that could damage the camera.
Do not shoot direct images that are extremely bright (e.g., light source, sun, etc.), and when camera
is not in use, put the lens cap on.
Follow the instructions in Chapter 6, “External connector pin assignment” for connecting the camera.
Improper connection may cause damages not only to the camera but also to the connected devices.
Confirm the mutual ground potential carefully and then connect the camera to monitors or computers.
AC leaks from the connected devices may cause damages or destroy the camera.
Do not apply excessive voltage. (Use only the specified voltage.) Unstable or improper power supply
voltage may cause damages or malfunction of the camera.

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
4
The voltage ripple of camera power DC +12V±10% shall be within ±50mV. Improper power
supply voltage may cause noises on the video signals.
The rising time of camera power supply voltage shall be less than +10V, Max 60ms. Please
avoide noises like chattering when rising.
2ch output CCD, separated into right and left, is utilized for VCC-G60FV11CL. Image signals for
right half screen and left half screen are output via each independent circuit. Therefore, differences
between right screen and left screen could be seen depending on the usage conditions (shooting
conditions /temeperature conditions and so on). CIS trys its best to adjust this differences but please
be noted it would not be perfect.
3. Product Outline
VCC-G60FV11CL is a Camera Link interfaced, high-resolution industrial black and white video camera module
utilizing a 2/3 type PS IT CCD. 5M pixels CCD image sensor with on-chip micro-lenses realizes high
sensitivity and high resolution. At Full Frame Scan Mode, entire pixels can be read out within approx. 1/16s.
Features
□Camera settings can be changed via serial communications.
□Shutter speed can be set from 1/16sec ～1/100,000sec by 1H.
□At partial scan mode, both capturing start position and capturing width can be set by 3H.
10 4020 30 50
10
11
12
[V]
Voltage Rising Time [ms]
9
8
7
60 70
Power Supply Voltage

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
5
4. Specification
4.1. General Specification
Item
Specification
Pickup device
Device Type
2/3 type Interline Transfer B/W CCD, Sony ICX625AL
Effective Pixel Number
2456 (H) x 2058 (V)
Unit Cell Size
3.45μm (H) x 3.45μm (V)
Chip Size
9.93mm (H) x 8.70mm (V)
Videooutput frequency
Pixel Clock
64 MHz
Horizontal Frequency
33.264 KHz Pixel Clock: 1924CLK
Vertical Frequency
Full Frame Scan Mode: 2079 lines, approx 16.000Hz
Sync. system
Internal Sync. System
Video output standard
Camera Link
Resolution
2058 TV lines
Resolving power
8bit / 10bit
Sensitivity
F 5.6 400 lx (Shutter speed 1/16s, Gain 0dB)
Minimum illumination
F 1.4 1.5 lx (Shutter speed 1/16s, Gain +21dB)
Dust or stains in
optical system
No dust or stain shall be detected on the testing screen with setting the camera
aperture at F16.
Power requirements
DC +12V ±10% (Max voltage not to exceed +15V)
Power consumption
Approx. 3.6 W (At DC +12V IN, normal mode, and full frame scan mode)
Approx. 4.0 W (At DC +12V IN, normal mode, and partial scan mode)
Dimension
Refer to overall dimension drawing (Clause 12)
55mm x 55mm x 45mm (excluding projection)
Mass
Approx. 155 g
Lens mount
C mount (Refer to overall dimension drawing )
Optical axis accuracy
Refer to drawing for CCD Optical Axis Accuracy (Clause 11)
Gain variable range
0～21dB (Analog Gain; 0dB～+15 dB, Digital Gain; 15 dB～+21dB)
Shutter speed
variable range
1/16～1/100,000s
Trigger shutter mode
・Standard Trigger Mode ・Pulse Width Trigger Mode

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
6
Item
Specification
Safety/Quality
standards
UL: Conform to UL Standard including materials and others.
RoHS: Conform to RoHS
CE: EN55022:2006 Class A for Emission
EN61000-6-2:2005 for Immunity
FCC: To be applied to FCC Class A digital Device
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Durability
Vibration
Acceleration
98 m/s2(10.0G)
Frequency
20～200 Hz
Direction
XYZ 3 directions
Testing time
120 min for each direction
Shock
No mulfunction shall be occurred with 980m/s2(100G) for X, Y, Z
direction. (without package)
Operation environment
Temperature
Performance guaranteed temperature: 0℃～+40℃
Camera operation guaranteed temeprature: -5℃～+45℃
※All the specifications specified in this manual is guaranteed
under performance guaranteed temperature.
※All the camera functions operate normally under operation
guaranteed temperature
Humidity
RH 20～80% with no condensation
Storage environment
Temperature
-25℃～+60℃
Humidity
RH 20～80% with no condensation

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
7
4.2. Camera Output Signal Specification
Item
Specification
Video output
data
Video out
2448 (H) x 2058 (V)
(1224(H) x 2058(V) x 2TAP)
At Full Frame Scan Mode
64MHz 2Tap output
Sync. Signal
I/O
LVAL output
LVTTL (3.3V Output)
HR10-10R-12PA
FVAL output
LVTTL (3.3V Output)
DVAL output
LVTTL (3.3V Output)
Trigger input
Polarity
POSI/NEGA Selectable
Trigger Pulse width
Over 2 H(min.) ～Less than 4158 H(max.)
Camera Link Input
LVDS:CC1 input
Camera Link Connector
TTL Input
Refer to the below.
HR10-10R-12PA
100 Ω
1 k Ω470ｐ
Input
ｐTrigger
VIH Min 2.0V
VIL Max 0.8V
Video Signals
White Clip Level
At Digital 8bit
: FFh
Setup Level
At Digital 8bit
: 08h
Dark Shading
At Digital 8bit
: Under 08h for both horizontal and
vertical. (Conditions: Gain 0dB)
Leval differences
between right and left
At Digital 8bit
: Under 03h (Conditions: Gain 0dB)
Video Output
Data Sequence
AXY: Left half image data, Yth line, Xth pixel from the left.
BXY: Right half image data, Yth line, Xth pixel from the right.
X: 1～1224
Y: 1～2058

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
8
Data Bit of Camera Link Port (Base Configuration)
Port/bit
At 8bit output setting
At 10bit output setting
Port A0
A0:Left half image data:bit0[LSB]
A0: Left half image data:bit0[LSB]
Port A1
A1: Left half image data:bit1
A1: Left half image data:bit1
Port A2
A2: Left half image data:bit2
A2: Left half image data:bit2
Port A3
A3: Left half image data:bit3
A3: Left half image data:bit3
Port A4
A4: Left half image data:bit4
A4: Left half image data:bit4
Port A5
A5: Left half image data:bit5
A5: Left half image data:bit5
Port A6
A6: Left half image data:bit6
A6: Left half image data:bit6
Port A7
A7: Left half image data:bit7[MSB]
A7: Left half image data:bit7
Port B0
B0: Right half image data:bit0[LSB]
A8: Left half image data:bit8
Port B1
B1: Right half image data:bit1
A9: Left half image data:bit9[MSB]
Port B2
B2: Right half image data:bit2
(-)
Port B3
B3: Right half image data:bit3
(-)
Port B4
B4: Right half image data:bit4
B8: Right half image data:bit8
Port B5
B5: Right half image data:bit5
B9: Right half image data:bit9[MSB]
Port B6
B6: Right half image data:bit6
(-)
Port B7
B7: Right half image data:bit7[MSB]
(-)
Port C0
(-)
B0: Right half image data:bit0[LSB]
Port C1
(-)
B1: Right half image data:bit1
Port C2
(-)
B2: Right half image data:bit2
Port C3
(-)
B3: Right half image data:bit3
Port C4
(-)
B4: Right half image data:bit4
Port C5
(-)
B5: Right half image data:bit5
Port C6
(-)
B6: Right half image data:bit6
Port C7
(-)
B7: Right half image data:bit7
※5 secounds shall be waited after turning on power to get proper camera operation.

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
9
4.3. CCD Spectral Response (Representative Value)
※Lens charcteristics and luminous source charcteristics are not considered.

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
10
5. Function Settings
Camera functions can be set with serial communications.
Function
Address
Data
Gain
001
0:
0 dB: Analog Fixed Gain
1:
+6 dB: Analog Fixed Gain
2:
+12 dB: Analog Fixed Gain
3:
+15 dB: Analog Fixed Gain
4:
+21 dB: Analog Gain (+15 dB) + Digital Gain (+6 dB)
5:
Manual Gain Interlocked right and left (Refer to Address 006)
6:
Manual Gain Independent right and left
(Refer to Address 006 for the right. Refer to Address 008 for the left.)
E-Shutter
002
0:
1/16s(Off)
1:
1/30s
2:
1/60s
3:
1/90s
4:
1/120s
5:
1/150s
6:
1/200s
7:
1/250s
8:
1/500s
9:
1/750s
10:
1/1000s
11:
1/2000s
12:
1/5000s
13:
1/10000s
14:
1/15000s
15:
1/100000s
16:
Manual Shutter (Refer to Address 009 & 010)
Trigger Mode
004
0:
Normal Mode (Trigger Mode Off)
1:
Standard Trigger Mode (Shutter speed can be set with address 002.)
2:
Pulse Width Trigger Mode (Shutter speed can be set with trigger pulse width.)
Manual Gain
(Total & Right)
006
0～255:
※When the data of address 001 is 005, Total Gain (Interlocked R and L.)
※When the data of address 001 is 006, Right Gain (Independent R and L.)
Manual Gain (Left)
008
0～255:
※When the data of address 001 is 005/006, Left Gain (Independent R and L)
Manual Shutter Control
009&010
0～2078:
1/16s (Off)～1/100,000s ※Set the address 002 data to 016.
Address 009 MSB and address 010 LSB makes total 16 bit.
Shutter speed = (2078-(009&010)) x30.0625μs +10.00μs
Note: shutter speed will be 10μs at 2078s (1/100,000) Max Data=2078
Trigger Polarity
011
0:
Positive Input
1:
Negative Input
Trigger Input Select
012
0:
Camera Link Connector 12226-1100-00-PL
1:
Circular Connector HR10-7R-6PA
Output Data Select
013
0:
8bit Output Data
1:
10bit Output Data
Partial Scan Mode
015
0:
Full Frame Scan Mode
1:
Partial Scan Mode

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
11
Function
Address
Data
Partial Scan Start Position
016&017
0～685:
Set the address 015 data to 001.
Address 016 MSB and address 017 LSB makes total 16 bit.
Start Position: 3 Lines/step
Min Data: 0 (0 Line)/Max Data : 685 (2055 Lines)
Start Position (016&017)+ Effective Lines (019&020) <= 685
Partial Scan Effective Lines
019&020
0～684:
Set the address 015 data to 001.
Address 019 MSB and address 020 LSB makes total 16 bit.
Effective Lines: 3 Lines/step
Min Data: 0 (3 Lines)/Max Data : 685 (2058 Lines)
Start Position (016&017)+ Effective Lines (019&020) <= 685
Partial Scan Total Lines
021&022
0～2078:
Read Only
Total line number at Partial Scan Mode or Full Frame Scan Mode minus 1 is set
Manual Digital Gain (Right)
126&127
256～
512:
※Set address 001 data to 005/006.
Manual Digital Gain (Left)
128&129
256～
512:
※Set address 001 data to 005/006.
Data Save
255
Input 083 to save the data in EEP-ROM.
Note: The data set with 2 Byte with Manual Analog/Digital Gain control, Manual Shutter Control, Partial Scan
Start Position, and Partial Scan Effective Line shall be set with High Byte first, then set with Low Byte. The
camera rewrites the internal resister when receiving Low Byte.

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
12
6. External Connector Pin Assignment
6.1. 12 pins Circular Connector HR10-10R-12PA (HIROSE)
6.2. 26 pins Camera Link Connector 12226-1100-00 PL (SUMITOMO 3M)
Pin No.
1
GND
2
POWER IN DC +12V
3
GND
4
NC
5
GND
6
LVAL/OUT
7
FVAL/OUT
8
GND
9
NC
10
DVAL/OUT
11
Trigger IN
12
GND
Pin No.
Pin No.
1
GND
14
GND
2
X0-
15
X0+
3
X1-
16
X1+
4
X2-
17
X2+
5
Xclk-
18
Xclk+
6
X3-
19
X3+
7
SerTC+
20
SerTC-
8
SerTFG-
21
SerTFG+
9
CC1-(Trigger IN-)
22
CC1+ (Trigger IN+)
10
CC2+
23
CC2-
11
CC3-
24
CC3+
12
CC4+
25
CC4-
13
GND
26
GND

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
13
LVAL Output
Video Output
DVAL Output
FVAL Output
1234567891020762075 11 12 21 23 24
(CCD Read Out Signal)
9H
21H2058H
12H
Total = 2079H
207920782077
2058H
22
LVAL Output
700 CLK
Video Output
DVAL Output
700 CLK
FVAL Output
1924 CLK
1224 CLK
Pixel CLK = 64MHz
2Tap Output
1 CLK
7. Timing Chart
7.1. Horizontal Synchronous Signals Timing
7.2. Full Frame Scan Mode Timing

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
14
LVAL Output
Video Output
FVAL Output
DVAL Output
12H
TTL INx
( CCD Read
Out Signal)
Exposure Time
( nHD×30.0625μs+10.00μs)
1 9
22 2079
2058 H
2070 H
(Trigger Input)
TTL INx
(Trigger Input)
(Sub Pulse)
(CCD Read Out Signal)
1.328μsDelay(Fixd)
(Exposure Signal)
LVAL Output
Video Output
FVAL Output
DVAL Output
12 H
TTL INx
( CCD Read
Out Signal )
Exposure Time
1 9
22 2079
2058 H
2070 H
(Trigger Input)
TTL INx
(Trigger Input)
(Sub Pulse)
(CCD Read Out Signal)
1.328μsDelay (Fixd)
SP Output
(Exposure Signal)
10.00μsDelay (Fixd)
7.3. Standard Trigger Mode Timing
7.4. Pulse Width Trigger Timing
※Note to the startup in Standard Trigger Mode and Pulse Width Mode
If you turn on your camera in Trigger Mode, enter the dummy trigger signal three or more times in order
to stabilize the CCD operation

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
15
FVAL Output
(Normal Scan)
9 H
Video Output
(Normal Scan)
2079 H
Video Output
(Partial Scan)
FVAL Output
(Partial Scan)
9 H
12 H
Total Line(Address 021&022) + 1H
2058 H
Y Offset
12H + Starting Position
(Address016&017)
Effective Line
(Address 019&020)×3+3H
High Speed
Transmit Term
High Speed
Transmit Term
8. Partial Scan Mode Details
Reading out position register (Address 016 & 017): 0 (0Line) ~685 (2055Lines) 3Lines/step
Effective line register (Address 019 & 020): 0 (3Lines) ~685 (2058Lines) 3Lines/step
Total line register (Address 021 & 022): 706Lines + (Effective line register × 2) + 2 (Read Only)
Note: Reading out position and effective lines shall meet the following conditions.
Reading out position register + Effective line register = < 685
Otherwise, the value, 685 –reading out position register, will be set to the effective line register.
<Example 1> Conditions: Reading out position register (Address 016 & 017) = 000
Effective line register
(Address 019 & 020)
Effective lines
Total line register
+1 Line
Frame Rate
0
3 Lines
709 Lines
46.92 fps
・
・
・
・
226
681 Lines
1161 Lines
28.65 fps
・
・
・
・
426
1281 Lines
1561 Lines
21.31 fps
・
・
・
・
685
2058 Lines
2079 Lines
16.00 fps
※In Partial Scan Mode, the border between 2 readout taps corresponding to right and left portions in a
monitor might be noticeable.
In that case, set the data of address“001” (Gain) to“006” (Manual Gain - Independent control of 2 taps).
And set the data of address 006 to the right and the data of address 008 to the left, then adjust the
brightness difference between the right and left.

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
16
9. Remote Interface Function
Through serial port of 12pin connector at rear, the camera can be controlled.
(1) The settings for RS-232C
(2) Control code
・The total control code is 14 bits, which conforms to ASCII code.
・The control code consists of camera No. process code, remote controller address, remote
controller data, and CR. Execute Read/Write through PC, and the camera will reply the data.
1
2
3
4
5
6
7th Byte
8
9
10
11
12
13
14
Camera No.
Process code
Remote controller
address
Remote controller data
CR
000000: fixed
“R”Read mode
Please refer to the
address table of
Section 5. Function
Settings.
000～255
0 Dh
“W”Write mode
“C”Camera mode
Camera No. is fixed with 6 bite numerical strings, “000000”.
Process code
Input any one of R, W, or C to the process code.
R (read mode) is to read the data of remote controller address.
Please be noted to set any dummy data (000～255) to 11th ～13th, since a command shall
consists of 14 bytes.
W (write mode) is to write the data to the remote controller address.
Please be noted that the data cannot be saved into EEPROM of the camera.
(Reboot the camera, and the data is reset to the initial setting.)
To save the data into EEPROM, please refer to Section 5. Function Settings.
C is the code to send the data back from the camera.
Note: Do not set code C when sending the data from PC side.
Baud rate
:9600bps
Data
:8bit
Stop bit
:1bit
Parity
:None
XOn/XOff
:Not controlled

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
17
Remote controller address
Note: Do not write the data into the address other than specified, since it may cause
the damages or malfunction of the camera.
Remote controller data
Set the decimal number (000～255) for the remote controller data. Please be noted to set any
dummy data at read control mode.
CR
Be sure to input “CR”to confirm the end of the command.
※Note: The data set with 2 Byte with Manual Analog/Digital Gain control, Manual Shutter Control,
Partial Scan Start Position, and Partial Scan Effective Line shall be set with High Byte first, then set with
Low Byte. The camera rewrites the internal resister when receiving Low Byte.
10. Initial Settings
Function
Address
Data
Gain
001
0: 0dB
E-Shutter
002
0: 1/16s (Off)
Trigger Mode
004
0: Normal Mode (Trigger Mode Off)
Trigger Polarity
011
0: Positive Input
Output Data Select
013
0: 8 bit Output Data
Partial Scan Mode
015
0: Full Frame Scan Mode
Partial Scan Total Lines
021 & 022
2078: Read Only

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
18
Datum Plane B
55
55
Datum Plane A
Inclination of optical axis
to datum plane A
Inclination of optical axis
to datum plane B
11.1 6.3 45
Datum Plane
A
910-004-00-00
*)Dimensions from datum plane A to the center of the lens mount
The center of effective pixels shall be
within 0.6 phai to the center
of lens mount
Incliation of effective pixels theta to datum plane A
Theta shall be under ±0.5°
(Unit: mm)
90°±0.2°
Under±0.5°
27.5±0.3(*)
Theta±0.5°
11. CCD Optical Axis Accuracy

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
19
28±0.1
28±0.1
55
55
45
5M PIXEL
Under R1
6.3
11.1
37
35±0.1
4.5±0.1
CL
DC IN
999-501-00-00
F 29 0
-0.05
4-M3
Depth 4
CMount (*)
4-M3
Depth 4
Product Name Label Position
(Unit: mm)
*) Screw length from C mount lens surface shall be under 6mm. And, protruding portion shall be less than 10mm.
*) C Mount screws comply with ANSI/ASME B1.1, 1-32UN(2B).
12. Dimensions

VCC-G60FV11CL Rev.900-684-34
©2014 CIS Corporation. All rights reserved.
20
13. Cases for Indemnity (Limited Warranty)
We shall be exempted from taking responsibility and held harmless for damage or losses incurred by the user
in the following cases.
In case damage or losses are caused by fire, earthquake, or other acts of God, acts by third party,
deliberate or accidental misuse by the user, or use under extreme operating conditions.
In case indirect, additional, consequential damages (loss of business interests, suspension of
business activities) are incurred as result of malfunction or non-function of the equipment,
we shall be exempted from responsibility for such damages.
In case damage or losses are caused by failure to observe the information contained in the
instructions in this product specification & operation manual.
In case damage or losses are caused by use contrary to the instructions in this product specification
& operation manual.
In case damage or losses are caused by malfunction or other problems resulting from use of
equipment or software that is not specified.
In case damage or losses are caused by repair or modification conducted by the customer or any
unauthorized third party (such as an unauthorized service representative).
Expenses we bear on this product shall be limited to the individual price of the product.
14. CCD Pixel Defect
CIS compensates the noticeable CCD pixel defects found at the shipping inspection prior to our shipment.
On very rare occasions, however, CCD pixel defects might be noted with time of usage of the products.
Cause of the CCD pixel defects is the characteristic phenomenon of CCD itself and CIS is exempted from
taking any responsibilities for them.
Should you have any questions on CCD pixel defects compensation, please contact us.
15. Product Support
When defects or malfunction of our products occur, and if you would like us to investigate on the cause
and repair, please contact your distributors you purchased from to consult and coordinate.