CIS VCC-G20V30A Quick start guide

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
29mm Cubic VGA
B/W Analog Camera
VCC-G20V30A
Product Specification
& Operational Manual
CIS Corporation
En
g
lish

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
2
Table of Contents
1. Scope of Application...............................................................................................................................3
2. Handling Precautions .............................................................................................................................3
3. Product Outline......................................................................................................................................4
4. Specification..........................................................................................................................................5
4.1. General Specification .......................................................................................................................5
4.2. Camera Input/Output Signal Specification............................................................................................7
4.3. CCD Spectral Response (Representative value).....................................................................................8
5. Function Settings...................................................................................................................................9
6. External Connector Pin Assignment ....................................................................................................... 13
6.1. 12 pins Circular Connector HR10-10R-12PA (HIROSE) ...................................................................... 13
7. Timing Chart........................................................................................................................................ 14
7.1. Horizontal Sync Timing ..................................................................................................................... 14
7.2. Vertical Sync Timing ......................................................................................................................... 14
7.2.1. Full Frame Scan Mode.................................................................................................................... 14
7.2.2. 2:1 Interlaced Scan Mode (At Normal Shutter Mode)........................................................................ 15
7.2.3. Binning Mode (At Trigger Shutter Mode) ......................................................................................... 15
7.2.4. 1/2 Partial Scan Mode.................................................................................................................... 16
7.2.5. 1/4 Partial Scan Mode.................................................................................................................... 16
7.3. Restart-Reset Mode (Long Time Exposure) Timing ........................................................................ 17
7.4. Trigger Shutter Mode Timing......................................................................................................... 17
7.4.1. Fixed Trigger Shutter Mode (Sync Reset)......................................................................................... 17
7.4.2. Pulse Width Trigger Shutter Mode 1 (Sync Rese).............................................................................. 18
7.4.3. Pulse Width Trigger Shutter Mode 2 (Sync Non-Reset) ..................................................................... 18
8. CCD Optical Axis Accuracy.................................................................................................................... 19
9. Dimensions ......................................................................................................................................... 20
10. Cases for Indemnity (Limited Warranty)............................................................................................... 21
11. CCD Pixel Defect ................................................................................................................................ 22
12. Product Support................................................................................................................................. 22

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
3
1. Scope of Application
This is to describe VCC-G20V30A analog B/W CCD Camera. All specifications contained herein are subject to
change without prior notice. Reproduction in whole or in part is prohibited.
2. Handling Precautions
The camera must not be used for any nuclear equipments or aerospace equipments with which mechanical
failure or malfunction could result in serious bodily injury or loss of human life. Our warranty does not apply to
damages or defects caused by irregular and/or abnormal use of the product.
Please observe all warnings and cautions stated below.
Our warranty does not apply to damages or malfunctions caused by neglecting these precautions.
zDo not use or store the camera in the following extreme conditions:
¾Extremely dusty or humid places.
¾Extremely hot or cold places (operating temperature –5 to +45 )󳙱󳙱
¾Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.
¾Places subject to fluorescent light reflections.
¾Places subject to unstable (flickering, etc.) lighting conditions.
¾Places subject to strong vibration.
zDo not apply excessive force or static electricity that could damage the camera.
zDo not shoot direct images that are extremely bright (e.g., light source, sun, etc.), and when camera
is not in use, put the lens cap on.
zFollow the instructions in Chapter 6, “External connector pin assignment” for connecting the camera.
Improper connection may cause damages not only to the camera but also to the connected devices.
zConfirm the mutual ground potential carefully and then connect the camera to monitors or computers.
AC leaks from the connected devices may cause damages or destroy the camera.
zDo not apply excessive voltage. (Use only the specified voltage.) Unstable or improper power supply
voltage may cause damages or malfunction of the camera.
zThe voltage ripple of camera power DC +12V±10% shall be within ±50mV. Improper power
supply voltage may cause noises on the video signals.
In case of abnormal operation, contact the distributor from whom you purchased the product.

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
4
3. Product Outline
VCC-G20V30A is a high-resolution industrial B/W analog camera module utilizing a 1/3” inch PS IT CCD.
330K pixels CCD image sensor with on-chip micro-lenses realizes high sensitivity and high resolution.
Key Features
□ HD/VD sync input or Trigger input are valid.
□ OFF and 1/200s ～1/20,000s , 8 steps shutter speed can be set by rear switch.
10μs ～250ms shutter speed can be set by trigger pulse width.
□ Frame rates, 60fps and 30fps, are selectable.
□ 1/2 Partial scan mode, 1/4 Partial scan mode, and Binning mode are available.
□ Restart Rest mode to enable long time exposure can be set.
□ 2:1 Interlaced Mode (at normal shutter mode) is available.
□ Scanning rates are switchable by the input level to 9pins circular connector at rear.
□ Only 29mm cubic in size (excluding projection), light weight 45g, and speed makes it a best match for
use in embedded systems.
□ As an optional function, γ=0.45, HD/VD 75Ωimpedance can be set as the factory initial setting.
Please ask us for the details.

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
5
4. Specification
4.1. General Specification
Item Specification
Pickup device
Device Type 1/3” Interline Transfer B/W CCD, Sony ICX424AL
Effective Pixel Number 659(H) x 494 (V)
Unit Cell Size 7.4μm (H) x 7.4μm (V)
Chip Size 5.79mm (H) x 4.89mm (V)
Video output frequency
60fps
Mode
Pixel Clock 24.5454 MHz
Horizontal Frequency 31.468 kHz Pixel Clock 780 CLK
Vertical Frequency
Full Frame Scan Mode
Scanning lines 525 H 59.94 Hz
Binning Mode *1
Scanning lines 262.5 H 119.9 Hz
1/2 Partial Scan Mode
Scanning lines 262 H 120.1 Hz
1/4 Partial Scan Mode
Scanning lines 131 H 240.2 Hz
30fps
Mode
Pixel Clock 12.2727 MHz
Horizontal Frequency 15.734kHz Pixel Clock 780 CLK
Vertical Frequency
Full Frame Scan Mode
Scanning lines 525 H 29.97 Hz
Binning Mode *1
Scanning lines 262.5 H 59.94 Hz
1/2 Partial Scan Mode
Scanning lines 262 H 60.05 Hz
1/4 Partial Scan Mode
Scanning lines 131 H 120.1 Hz
*1 At normal operation, the camera functions as 2:1 interlaced scan mode.
Sync. system Internal sync & HD/VD external sync
(Internal/External recognized automatically)
Video output standard Analog
Resolution 480 TV lines
Sensitivity F5.6 400 lx (60fps: Shutter speed 1/60s, Gain 0dB, 3200K)
Minimum illumination F1.4 1.5 lx (60fps: Shutter speed 1/60s, max Gain VS 50IRE)
S/N ratio 56dB
Dust or stains in
optical system
No dust or stain shall be detected on the testing screen with setting the camera
aperture at F16.

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
6
Item Specification
Power requirements DC +12V ±10% (Max voltage not to exceed 15V)
Power consumption 1.6 W typ (max. 2W) at DC +12V IN
Dimension Refer to overall dimension drawing (Clause 9)
29mm x 29mm x 29mm (excluding projection)
Mass Approx. 45 g
Lens mount C mount (Refer to overall dimension drawing)
Optical axis accuracy Refer to drawing for CCD Optical Axis Accuracy (Clause 8)
Gain variable range 0～12dB (guaranteed range)
Gamma 1 (fixed)
Shutter speed
variable range
Switch:
60fps Mode: OFF(1/60), 1/200, 1/500, 1/1000, 1/2000, 1/4000, 1/8000, 1/20000s
30fps Mode: OFF(1/30), 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000s
Pulse Width: 10μ～250ms
Operation Mode
Fixed Trigger Shutter Mode (Exposure time can be set with rear switch).
Pulse Width Trigger Shutter Mode (Exposure time can be set with trigger pulse
width.)
Safety/Quality
standards
UL: Conform to UL Standard including materials and others.
RoHS: Conform to RoHS
CE: Conform to EN55022:2006 (Class B): Emission
Conform to EN61000-6-2:2005: Immunity
Conform to FCC Class A digital Device
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Durability
Vibration
Acceleration 98 m/s2(10.0G)
Frequency 20～200 Hz
Direction XYZ 3 directions
Testing time 120 min for each direction
Shock No malfunction shall be occurred with 980m/s2(100G) for ±X, ±
Y, ±Z, 6 directions. (without package)
Operation environment
Temperature Operation guaranteed: -5℃～+45℃
Performance guaranteed: 0℃～+40℃
Humidity RH 20～80% with no condensation
Storage environment Temperature -25℃～+60℃
Humidity RH 20～80% with no condensation

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
7
4.2. Camera Input/Output Signal Specification
Item Specification
Video output Effective output: 648(H) × 494(V) at full frame scan mode
Sync signals
Input /Output
HD/VD Input signal level: 2～5Vp-p
Input impedance: 10kΩ. 75Ωcan be set as an optional factory setting.
Allowable frequency deviation: ±3%
Phase difference: HD/VD: under 0±5μs
Jitter: under 20ns
HD/VD/WEN output
CMOS (74VHC04 equivalent)
Output impedance 100Ω
HD/VD/WEN output signal level
Low 0.5V (max), High 4V (Min)
Trigger input Polarity: Positive
Input si
g
nal level: Low 0.5V (max), High 2.5～5V
Input impedance: 1kΩ
Trigger input width: 4μs ～250ms
Scan IN input
9 pins scan select
Input signal level: Low 0.5V (max) High 2.5～5V
Input impedance: 10kΩ(Pull Up)
Video signal VS output 1.0V (p-p), Sync. Negative, 75Ωunbalanced, DC connect
White clip level: 840 ± 70 mVp-p
Setup level: 25 ± 15 mVp-p (Gain 0dB)
SYNC level: 290 ± 50 mVp-p
VS DC level: 0 ± 100 mV

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
8
4.3. CCD Spectral Response (Representative value)
※ Lens characteristics and illuminant characteristics are not considered.

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
9
5. Function Settings
1 E2 ◇Shutter Speed 3bit, 8step
2 E1 OFF (1/60) ～1/20,000s (60fps mode)
3 E0 OFF (1/30) ～1/10,000s (30fps mode)
4 Mode 1 ◇Trigger Shutter Mode 2bit
5 Mode 0 Normal, Fixed Trigger Shutter, Pulse Width Trigger Shutter
6 Scan 1 ◇Scan Mode 2bit
7 Scan 0 Full frame scan, Binning, 1/2, 1/4 Partial scan
8 Scan En ◇Scan Enable (No.9pin of 12pins circular connector Valid/Invalid)
9 Speed ◇Changing frame rate, 60fps mode/30fps mode
10 IN/OUT ◇HD/VD signal input and output setting (No. 6 & 7 pin of 12pins circular
connector)
OFF
● Indicates initial setting position.
Other Optional Functions (Ex-factory setting)
◇ HD/VD75Ωimpedance
◇ γ= 0.45 compensation
Please ask us for the details.
Shutter Speed Settings
E2 E1 E0 Shutter Speed Actual Time
SW1 SW2 SW3 Normal
T
ri
gg
er
OFF OFF OFF OFF(1/60s) 16.67 ms 8.33 ms
OFF OFF ON 1/200 sec 5.0 ms 5.0 ms
OFF ON OFF 1/500 sec 2.0 ms 2.0 ms
OFF ON ON 1/1000 sec 1.0 ms 1.0 ms
ON OFF OFF 1/2000 sec 490 μs 495 μs
ON OFF ON 1/4000 sec 240 μs 243 μs
ON ON OFF 1/8000 sec 113 μs 116 μs
ON ON ON 1/20000 sec 51 μs 52 μs
※ Shutter speed and actual time shown above is for 60fps mode. With 30fps mode, the actual time
will be double.
Indicates initial setting position
Operational Mode Settings
MODE1 Mode0 Setting Mode
SW4 SW5
OFF OFF Normal Shutter Mode (including Restart-Reset Operation)
OFF ON Fixed Trigger Shutter Mode (Sync Reset Type)
ON OFF Pulse Width Trigger Shutter Mode 1 (Sync Reset Mode)
ON ON Pulse Width Trigger Shutter Mode 2 (Sync Non-Reset Mode)
Indicates initial setting position
●
●
●
●
●
●
●
●
●
●

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
10
Table of Settings
Shutter Mode
Function
Normal
Shutter
Mode
Fixed Trigger
Shutter Mode
(Sync Reset)
Pulse width trigger
Shutter Mode 1
(Sync Reset)
Pulse width trigger
Shutter Mode 2
(Sync Non-reset)
Shutter speed by switch 1󳥫󳘻 󳥫× ×
Shutter speed by pulse width × × 󳥫󳥫
Full Frame Scan 󳥫󳥫󳥫󳥫
Binning Scan 󳥫󳘻2 󳥫󳥫󳥫
Partial Scan 󳥫󳥫󳥫󳥫
HD/VD Input 󳥫HD󳥫HD󳥫󳥫
HD/VD Output 󳥫󳥫󳥫×
󳘻1 When using the camera with Restart-Reset Mode, shutter speed setting switch shall be OFF.
󳘻2 2:1 interlaced scan can be valid but restart-reset mode cannot be operated at normal shutter mode.
Normal Shutter Mode
Each scanning mode and HD/VD external sync input and sync output are valid.
When adding external sync input, please follow the HD/VD input conditions shown below.
Restart-Reset Mode
Restart-reset mode (Long time exposure mode) is valid at normal mode, with setting the shutter to OFF, HD/VD
sync input ON, and adding external EXT HD input. With adding EXT VD at random timing with over 1VD, data
for one screen image is read out. This function is useful when sensitivity with regular exposure time is not
sufficient or when indicating the locus of moving object. Restart-reset operation corresponds to all scanning
modes except 2:1 interlaced scan mode.
Fixed Trigger Shutter Mode (Sync Reset Mode)
At fixed trigger shutter mode, exposure time is set by the shutter value of switch at camera rear. With trigger
input, images can be captured at any timing.
Internal SYNC and VD are reset right after completion of exposure so that the video output signals are read out
at the shortest timing. HD external input is valid but VD external input invalid.
Exposure time = Value of switch at rear
Conditions: Trigger input pulse width shall be 4μs～250ms, Positive Logic
The shortest trigger cycle = 1 frame + 5H

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
11
Pulse width trigger shutter mode 1 (Sync Reset Mode)
At pulse width trigger shutter mode, exposure time and shutter value can be set by trigger pulse width.
With trigger input, images can be captured at any timing.
Internal SYNC and VD are reset right after completion of exposure so that the video output signals are read out
at the shortest timing. HD external input is valid but VD external input invalid.
Exposure time = Trigger pulse width (μs) + 5μs typical
Conditions: Trigger input pulse width shall be 4μs～250ms, Positive Logic
The shortest trigger cycle = 1 frame + 5H
Pulse width trigger shutter mode 2 (Sync Non-Reset Mode)
At pulse width trigger shutter mode, exposure time and shutter value can be set by trigger pulse width.
With trigger input, images can be captured at any timing.
Signals are read out after waiting for the external VD (single) input so that the timing to read out video output
signals can be controlled externally. The down edge phase of external HD/VD signals should be matched.
The time frame between down edge of trigger input and to add single VD externally shall be set 10μ～35ms.
Exposure time = Trigger pulse width (μs) + 5μs typical
Conditions: Trigger input pulse width shall be 4μs～250ms, Positive Logic
The shortest trigger cycle = Trigger pulse width + VD waiting time + 1 frame + 2H
Caution 1: When the next trigger is input before the completion of video signals output for the prior trigger,
the images could be improper.
Caution 2: Smear or blooming could occur when strong incident light is extensively illuminated, with setting the
electric shutter at high speed. To avoid this smear or blooming, lower the volume of incident light or
use a stroboscopic light source to control the light volume.
Caution 3: Please refer to the exposure timing chart below for the actual timing to start exposure after adding
trigger input, and or for the actual timing to complete exposure at pulse width trigger shutter
operation.

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
12
Scan Mode Settings
Scan 1 Scan 0 Setting Mode
SW6 SW7
OFF OFF Full Frame Scan Mode
OFF ON Binning Mode or 2:1 Interlaced Scan Mode
ON OFF 1/2 Partial Scan Mode
ON ON 1/4 Partial Scan Mode
When setting scan mode with No.9pin of 12pins circular connector
SW8 OFF No.9pin invalid (Pull Up 10kΩ)
ON No.9pin valid Low Level
Indicates initial setting position
Scan modes set by SW6 and SW7
Scan Mode Frame Rate Scanning lines Blanking Lines Video output lines
(fps) (Lines) (Lines) (Lines)
Full Frame Scan Mode 59.94 525 23 494
Binning Mode 119.9 262.5 20 242.5
1/2 Partial Scan Mode 120.1 262 32 222
1/4 Partial Scan Mode 240.2 131 38 76
The value shown above is for 60fps mode setting.
Changing the scan settings
Scan settings shall be changed basically by the settings of camera switch at rear, but it can be also changed by
the input level of No. 9pins of the circular connector at both Normal shutter mode and Trigger shutter mode.
①Set SW 8 ON at camera rear to enable No. 9 pins input of the circular connector.
②Select Binning Mode or Partial Scan Mode with SW 6 and 7 at camera rear.
③Change H/L input level of No. 9 pins of the circular connector.
High Level (2.5～5.0V) Low level (0.5V max)
Full Frame Scan Mode Binning Mode
PartialScanMode
Changing frame rate settings
SW9 OFF 60fps Mode Pclk=24.545MHz
ON 30fps Mode Pclk=12.272MHz
※Reboot the camera to change the pixel clock.
Changing HD/VD input and output
SW10 OFF HD/VD output
ON HD/VD input
Indicates the factory setting position

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
13
6. External Connector Pin Assignment
6.1. 12 pins Circular Connector SNH-10-12 (RPCB) (SAMWOO)
Pin No.
1 GND
2 Power In DC+12V
3 GND
4 Video Out
5 GND
6 HD In/Out
7 VD In/Out
8 GND
9 Scan In
10 WEN Out
11 Trig In
12 GND

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
14
Camera HD
78
Black Transmit
31 72 18
520 62
68 22
18 58 56
CCD
Output
Read Out Signal
Dummy Pixe ls Ef fe ct ive P ixe ls
659
Horizont al Blanking Video Out put Act ive Period
648CLK
Discharge Signal
Video Output
1H = 780CLK
132CLK
Camera VD
9H
Black Transmit Black
221 8 494
WEN Output
13
23
Vert ical Blanking
31 H 494 H
1V = 525H
E ff e c t ive P ixe ls
Exposure Time
CCD
Output
Read Out Signal
Discharge Signal
Video Output
494
1 2
Video Output Active Period
7. Timing Chart
7.1. Horizontal Sync Timing
7.2. Vertical Sync Timing
7.2.1. Full Frame Scan Mode

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
15
Camera VD
9 H 253.5 9 H 253.5
Transmit Black Transmit Black
110 4 110 4
Black ODD Field Black EVEN Field
262.5 262.5
20 H 242.5 H 20 H 242.5 H
WEN Output
The expansion waveform of a Sync period
Video Output Active Period
Exposure Time
Ve rt ical Blanking Video Out put Act ive Pe riod
Output
Read Out Signal
Discharge Signal
Video Output
Vertical Blanking
CCD
1V = 262.5H
493,4
494
9,10
490,1
8,9
491,2 493,4 492,3 491,2
7,8
Camera VD
9H
CCD
Black Transmit Black
1104 247
13
23
Video Output
Vertical Blanking
23 H 239 H
Video Output Active Period
1V = 262H
Read Out Signal
Discharge Signal
Exposure Time
Output
14,15
494
492,3 16,17 492,3
2,3
WEN Output
Effective Pixels
7.2.2. 2:1 Interlaced Scan Mode (At Normal Shutter Mode)
7.2.3. Binning Mode (At Trigger Shutter Mode)

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
16
Camera HD
262
Camera VD
14 230 14
22
32H 222H
357
Video Output Active Period
Hi
g
h Speed Transmit Period
1V = 262H
VφPulse
Read Out Signal
Discharge Signal
WEN Output
Exposure Time
Hi
g
h Speed Transmit Period
128 136
Video Output
Camera HD
131
Camera VD
21 83 23
28
38H 76H
Video Output
VφPulse
Read Out Signal
Discharge Signal
WEN Output
280
High Speed Transmit Period
1V = 131H
205 198
V
ideo Output Active Period
High Speed Transmit Period
Exposure Time
7.2.4. 1/2 Partial Scan Mode
7.2.5. 1/4 Partial Scan Mode

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
17
External VD
External HD
V
ide o O u tput
23H 494H
1V min
Read Out Signal
Exposure T ime
At Full Frame Scan
Exposure Time
WEN Output
Ple ase se t t h e sh ut t e r sp ee d w it h t h e fixe d sw it ch at c ame ra re ar.
Internal HD o
r
External HD
Internal VD Output
10 13 494H
Trigger Pulse Width : 4μs～250ms
V
ide o A c t ive Pe rio
d
Tri
gg
er Input
Read Out Si
g
na
l
WEN Output
Video Output
Exposure T ime
7.3. Restart-Reset Mode (Long Time Exposure) Timing
7.4. Trigger Shutter Mode Timing
7.4.1. Fixed Trigger Shutter Mode (Sync Reset)

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
18
Internal HD o
r
External HD
Internal VD Output
1～2
10 13 494H
WEN Output
Trigger Input
Read Out Si
g
na
l
Video Output
T
ri
gg
er Pulse Width : 4μs～250m
s
T rig g e r P u lse W id t h .
Exposure Time
Video Active Period
External HD
External VD Input
10 13 494H
WEN Output
T
ri
gg
er Pulse Width : 4μs～250m
s
O nly T rig ge r P u lse W id t h .
10μs～35ms
Video Active Period
Exposure T ime
Video Output
Trigger Input
Read Out Si
g
na
l
(Single Pulse)
7.4.2. Pulse Width Trigger Shutter Mode 1 (Sync Rese)
7.4.3. Pulse Width Trigger Shutter Mode 2 (Sync Non-Reset)

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
19
Inclination of
optical axis to
datum plane
2912
Datum
Plane
M2
M3
M2
29
29
The center of effective pixels shall be
within f 0.6 to the center of lens mount.
Inclination of effective pixels Theta
to datum plane shall be
?? ±0.5°
(*) Dimension from datum plane to the center of lens mount. 910-005-00-00
Datum
Plane
Product Name
Label Position( ? )
6±0.3 6±0.3
6±0.3 6±0.3
10±0.310±0.3
±0.2°
±0.5°
(Unit : mm)
14.5±0.3( *)
8. CCD Optical Axis Accuracy

VCC-G20V30A Rev.900-621-34-00
©2010 CIS Corporation. All rights reserved.
20
G20V30A
VGA
41
Φ28
12 29
*）
29
29
2-M2
Depth 3
12
4.5
Product Name
Label Position
4-M2
Depth 3
3-M3
Depth 3
22
23.7
20 12
4.5
3
DC12V/VS OUT
MGC
1
4
7
10
MODE
ONOFF
*）C Mount screws comply with ANSI/ASME B1.1, 1-32UN(2B).
*）Screw length from C mount lens surface shall be under 6mm.
And protruding portion shall be less than 10mm.
999-488-00-00
(M2 Size)
(M3 Size)
CMount (*)
(Unit:mm)
9. Dimensions