CIS VISION:elite VCC-F52U25CL Quick start guide

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
UXGA 3CCD Color
Camera Link Camera
VCC-F52U25CL
Product Specification
& Operational Manual
CIS Corporation
English

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
2
Table of Contents
PAGE
1. Scope of Application..................................................................................................................... 3
2. Handling Precautions .................................................................................................................... 3
3. Product Outline ............................................................................................................................ 5
4. Specification ................................................................................................................................ 6
4.1. General Specification.............................................................................................................. 6
4.2. Camera Output Signal Specification........................................................................................ 8
4.3 . CCD Spectral Response (Representative Value)...................................................................... 9
4.3.1. CCD (ICX274AL) Spectral Response ...................................................................................... 9
4.3.2. Prism Spectral Transmission Characteristics ........................................................................... 9
5. Function Settings...........................................................................................................................10
6. External Connector Pin Assignment ..............................................................................................12
6.1. 12 pins Circular Connector HR10-10R-12PA (HIROSE).............................................................12
6.2. Camera Link Connector 12226-1100-00PL (SUMITOMO 3M) ...................................................12
7. Timing Chart ..............................................................................................................................13
7.1. Horizontal Synchronous Signals Timing ..................................................................................13
7.2. Vertical Synchronous Signals Timing ......................................................................................13
7.3. Fixed Trigger Shutter Mode ...................................................................................................14
7.4. Pulse Width Trigger Shutter Mode..........................................................................................15
8. Partial Scan Mode Details ............................................................................................................16
9. Remote Interface Function ..........................................................................................................17
10. Initial Settings ............................................................................................................................18
11. CCD Optical Axis Accuracy ...........................................................................................................19
12. Dimensions ................................................................................................................................20
13. Cases for Indemnity (Limited Warranty)........................................................................................21
14. CCD Pixel Defect........................................................................................................................21
15. Product Support ........................................................................................................................21

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
3
1. Scope of Application
This is to describe VCC-F52U25CL, 3 CCD Color Camera Link Camera. All specifications contained
herein are subject to change without prior notice. Reproduction in whole or in part is prohibited.
2. Handling Precautions
The camera must not be used for any nuclear equipments or aerospace equipments with which
mechanical failure or malfunction could result in serious bodily injury or loss of human life.
Our warranty does not apply to damages or defects caused by irregular and/or abnormal use of the
product.
Please make sure to use the camera under the temperature conditions specified below. Our warranty
does not apply to damage or malfunction caused by ignoring these temperature conditions.
When the camera is used under ambient temperature over +30℃(86 degrees F), the temperature of
upper part or side part of the camera body should be kept under +55℃(131 degrees F).
Please consider proper heat dissipation in your system installation.
These recommendations apply even when camera is used under performance guaranteed temperature
and/or camera operation guaranteed temperature specified in our Specifications.
A temperature detecting sticker is enclosed for you to confirm and keep the camera body temperature
under +55℃. Please put the sticker on the camera as shown below and make sure that the circle for
60 is white.
With a rise in temperature, color of the sticker goes to black. The circle for 60 must be kept white.
(Please be noted that once the sticker color turns to black, it won’t be back to white again.)
50 55 60
<Example>：Ambient temperature +45℃(113 degrees F), calm →Installed on an aluminum board.
(120×200×5mm)

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
4
Please observe all warnings and cautions stated below.
Our warranty does not apply to damages or malfunctions caused by neglecting these precautions.
Do not use or store the camera in the following extreme conditions:
Extremely dusty or humid places.
Extremely hot or cold places (operating temperature –5℃to +45℃)
Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.
Places subject to fluorescent light reflections.
Places subject to unstable (flickering, etc.) lighting conditions.
Places subject to strong vibration.
Remove dust or dirt on the surface of the lens with a blower.
Do not apply excessive force or static electricity that could damage the camera.
Do not shoot direct images that are extremely bright (e.g., light source, sun, etc.), and when camera
is not in use, put the lens cap on.
Follow the instructions in Chapter 6, “External connector pin assignment” for connecting the camera.
Improper connection may cause damages not only to the camera but also to the connected devices.
Confirm the mutual ground potential carefully and then connect the camera to monitors or
computers. AC leaks from the connected devices may cause damages or destroy the camera.
Do not apply excessive voltage. (Use only the specified voltage.) Unstable or improper power
supply voltage may cause damages or malfunction of the camera.
The voltage ripple of camera power DC +12V±10% shall be within ±50mV.
Improper power supply voltage may cause noises on the video signals.
The rising time of camera power supply voltage shall be less than +10V, Max 60ms.
Please avoid noises like chattering when rising.
In case of abnormal operation, contact the distributor from whom you purchased the product.
10 4020 30 50
10
11
12
[V]
Voltage Rising Time [ms]
9
8
7
60 70
Power Supply Voltage

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
5
3. Product Outline
VCC-F52U25CL is a camera link interfaced, 3CCD high-resolution industrial color video camera module
utilizing a 1/1.8 type PS IT CCD. 2M pixels CCD image sensor with on-chip micro-lenses realizes high
sensitivity and high resolution. Entire pixels can be read out within approx. 1/30s.
Features
□Shutter speed can be set from 1/30sec ～1/54,000sec by fixed switch shutter trigger, and
1/15sec ～1/8,000 by pulse width trigger.
□Frame rates are as follows both at normal operation and trigger operation.
30 fps at full frame scan mode
30fps ～60fps at partial scan mode
□Trigger operation is CLK synchronized V-Sync Reset type. Delay time between capturing the
trigger pulse in the camera and starting exposure is approx. 0.96μsec (69CLK).
□At trigger operation, the new trigger input can be accepted even when outputting image signals
for the prior trigger input. However, the new trigger input during the exposure shall be ignored.
Please refer to the timing chart for the details.
□RGB 24bit/30bit are selectable.
Bundled Items
□Camera
□CIS Control Panel Software (For evaluation and demonstration purpose). ※
※Please ask for the details or download it from our web.

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
6
4. Specification
4.1. General Specification
Item
Specifications
(1) Pickup device
Device Type
1/1.8 type Interline Transfer Color CCD, SONY ICX274AL
Effective Pixel Number
1628(H) × 1236(V)
Unit Cell Size
4.40μm(H) × 4.40μm(V)
Chip Size
8.50mm(H) × 6.80mm(V)
(2) Video output
frequency
Pixel Clock
72 MHz
Horizontal Frequency
37.5000kHz
Pixel Clock: 1920 CLK
Vertical Frequency
Full Frame
Scan Mode
Scanning
Lines
1252 H
29.952 Hz
(3) Sync. system
Internal Sync. System
(4) Video output
standard
Camera Link (Base Configuration or Medium Configuration)
(5) Resolution
1200TV lines
(6) Resolving power
RGB 24bit (Base Configuration) or RGB 30bit (Medium Configuration) selectable
(7) Sensitivity
F5.6 2000lx (Shutter speed 1/30s(OFF), Gain 0dB)
(8) Minimum illumination
F1.4 40lx (Shutter speed 1/30s(OFF), Gain +12dB)
(9) Dust or stains in
optical system
No dust or stain shall be detected on the testing screen with setting the camera
aperture at F16.
(10) Power requirements
DC+12V±10% (Max voltage not to exceed 15V.)
(11) Power consumption
5.5W (At DC+12V IN, normal mode, and full frame scan mode.)
6.0W (At DC+12V IN, normal mode, and partial scan mode.)
(12) Dimension
Refer to overall dimension drawing (Clause 12)
H:55mm W:55mm D:60mm (excluding projection)
(13) Mass
Approx. 215g
(14) Lens mount
C mount (Refer to overall dimension drawing )
(15) Optical axis accuracy
Refer to drawing for CCD Optical Axis Accuracy (Clause 11)
(16) Gain variable range
0dB～+12dB (Guaranteed range)
(17) White balance
adjustment
guaranteed range
2800K～9000K (Guaranteed range)
(18) Shutter speed
variable range
Fixed Shutter: 1/30(OFF), 1/60, 1/90, 1/120, 1/150, 1/200, 1/250, 1/500, 1/750,
1/1,000, 1/1,500, 1/2,500, 1/5,000, 1/10,000, 1/54,000s
Pulse Width: 1/15～1/8,000s (Trigger input pulse width: 2,504H (max)～2H (min))
Manual Shutter: 1/30(Off)～1/54,000s
(19) Trigger shutter mode
・Fixed Trigger Shutter Mode ・Pulse Width Trigger Mode

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
7
Item
Specifications
(20) Safety/Quality
standards
UL: Conform to UL Standard including materials and others.
RoHS: Conform to RoHS
CE: Conform to EN55022:2006 (Class A) for Emission
EN61000-6-2:2005 for Immunity
FCC: To be applied
Conform to FCC Class A digital Device
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
(21) Durability
Vibration
Acceleration
: 21.6m/s2 (2.2G)
Frequency
: 7～30 Hz (Frequency varies every 5 minutes.
It shall be tested 15 minutes each for 3 directions.)
Direction
: X,Y, and Z, 3 directions
Testing time
: 15 min for each direction
Shock
No malfunction shall be occurred with 490m/s2(50G) for ±X, ±Y,
and ±Z, 6 directions. (without package)
(22) Operation
environment
Temperature
Performance guaranteed: 0℃～+40℃
Operation guaranteed: -5℃～+45℃
※Specifications specified in this manual are guaranteed under performance guaranteed temperature.
※Camera functions can operate normally under operation guaranteed temperature.
Humidity
RH 20～80% with no condensation
(23) Storage environment
Temperature
-25℃～+60℃
Humidity
RH 20～80% with no condensation

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
8
100Ω
470P
TTL Output
+5.0V(VCC)
TTL Input
HD74LV1GT32ACME
(RENESA)
Voh:3.8V(Min)
Vol:0.55V(Max)
1KΩ
HD74LV1GT14ACME
(RENESAS)
Vt-:0.5(Min)
Vt+:1.9V(Max)
100Ω
470P
4.2. Camera Output Signal Specification
Item
Specifications
(1) Video output data
Video out
1624(H) ×1224(V)
At Full Frame Scan Mode
(2) Sync. Signal I/O
HD(LVAL)
：6 pin
12pins circular connector (TTL Output)
VD(FVAL)
：7 pin
WEN(DVAL)
：10pin
EXP(Exposure)
：9 pin
LVAL
Camera Link Output (LVDS)
FVAL
DVAL
SP(Exposure)
(3) Trigger input
Polarity
Positive/Negative Selectable
Pulse width
Over 2H (min) ～Under 2504HD (max)
Trigger Input
：11pin
12pins circular connector (TTL Input)
CC1
Camera Link Input (LVDS)
(4) Serial
communication
SerTC (Serial to camera)
Camera Link Input (LVDS）
SerTFG (Serial to frame
grabber)
Camera Link Output (LVDS)
(5) Video output signal
White Clip Level
At Digital 8bit
: FFh
Setup Level
At Digital 8bit
: 08h
Dark Shading
At Digital 8bit
: Under 08h±04h
for both horizontal and vertical.
(Conditions: Gain 0dB)
※5 seconds shall be waited after turning on power to get proper camera operation.
12pins circular connector at rear, GPIO Interface

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
9
4.3. CCD Spectral Response (Representative Value)
4.3.1. CCD (ICX274AL) Spectral Response
※Lens characteristics, IR cut filter, and luminous source characteristics are not considered.
4.3.2. Prism Spectral Transmission Characteristics

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
10
5. Function Settings
Camera functions can be set with serial data communications.
Functions
Address
Data
Gain
001
0:
0
dB : Analog Fixed Gain
1:
+
3
dB : Analog Fixed Gain
2:
+
6
dB : Analog Fixed Gain
3:
+
12
dB : Analog Fixed Gain
4:
Manual Gain : over 0dB～+12dB (Refer to address 030&031.)
E-Shutter
002
0:
1/30s (Off)
1:
1/30s (Off)
2:
1/60s
3:
1/90s
4:
1/120s
5:
1/150s
6:
1/200s
7:
1/250s
8:
1/500s
9:
1/750s
10:
1/1000s
11:
1/1500s
12:
1/2500s
13:
1/5000s
14:
1/10000s
15:
1/54000s
16:
Manual Shutter (Refer to address 009＆010.)
White Balance
003
0:
THUR
1:
3200K
2:
THUR
3:
THUR
4:
Manual White Balance : Adjustment guaranteed range: over 2800K
～9000K (Refer to address 156&157, and 158&159)
Trigger Mode
004
0:
Normal Shutter Mode (Trigger Off)
1:
Fixed Trigger Shutter Mode
(Shutter speed can be set with address 002.)
2:
Pulse Width Trigger Shutter Mode
(Shutter speed can be set with trigger pulse width.)
Manual Shutter Control
009&010
0～1251:
1/30s(Off) ～1/54000s
※Set the data of address 002 to 016.
Address 009 MSB and address 010 LSB makes 16bit in total.
Shutter speed =(1251 - (009&010))×26.27μs+18.53μs
Max Data = 1251
Trigger Polarity
011
0:
Positive Input
1:
Negative Input
Trigger Input
012
0:
Camera Link (CC1) Input
1:
12pin Connector(11pin) Input

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
11
Functions
Address
Data
Output Data Select
013
0:
RGB 24bit Output Data
1:
RGB 30bit Output Data
Gamma Mode
014
0:
Gamma Off (1.0)
1:
Gamma On (Option)
Partial Scan Mode
015
0:
Full Frame Scan Mode
1:
Partial Scan Mode
Partial Scan Start Position
016&017
0～407:
※Set the data of address 015 to 001.
Address 016 MSB and address 017 LSB makes 16bit in total.
Start Position:3 H/step Min Data:0(0 H) / Max Data:407(1221 H)
Start Position(016&017) + Effective Line(019&020) <= 407
Partial Scan Effective Line
019&020
0～407:
※Set the data of address 015 to 001.
Address 019 MSB and address 020 LSB makes 16bit in total.
Effective Line:3 H/step Min Data:0(3 H) / Max Data:407(1224 H)
Start Position(016&017) + Effective Line(019&020) <= 407
Partial Scan Total Line
021&022
0～1251:
Read Only
Total line numbers at Partial Scan Mode or at Full Frame Scan Mode
minus 1H will be set.
Manual Analog Gain
030&031
0～512:
0:0dB ～512: over +12dB (Log Linear)
※Set the data of address 001 to 004.
Digital Gain G
128&129
256～512:
256:×1(0dB) ～512:×2(+6dB)
Manual White Balance R
156&157
256～1024:
256:×1(0dB) ～1024:×4(+12dB)
※Set the data of address 003 to 004.
Manual White Balance B
158&159
256～1024:
256:×1(0dB) ～1024:×4(+12dB)
※Set the data of address 003 to 004.
Data Save
255
Input 083 or 053 to save the data to EEP-ROM.
※Note: When setting the data with 2 Byte, High Byte shall be set first, then Low Byte to the next.
The camera rewrites the internal resister when receiving Low Byte.

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
12
1
14
13
26
CL
RGB 24bit Output
(Base Configuration)
RGB 30bit
(Medium Configuration)
Connector （A）
Connector （B）
6. External Connector Pin Assignment
6.1. 12 pins Circular Connector HR10-10R-12PA (HIROSE)
6.2. Camera Link Connector 12226-1100-00PL (SUMITOMO 3M)
Connector (A) Connector (B)
Pin No.
1
GND
2
Power In DC +12V
3
GND
4
NC
5
GND
6
HD(LVAL) Output
7
VD(FVAL) Output
8
GND
9
EXP(Exposure) Output
10
WEN(DVAL) Output
11
Trigger Input
12
GND
Pin No.
Pin No.
Pin No.
Pin No.
1
GND
14
GND
1
NC
14
GND
2
X0-
15
X0+
2
Y0-
15
Y0+
3
X1-
16
X1+
3
Y1-
16
Y1+
4
X2-
17
X2+
4
Y2-
17
Y2+
5
Xclk-
18
Xclk+
5
Yclk-
18
Yclk+
6
X3-
19
X3+
6
Y3-
19
Y3+
7
SerTC+
20
SerTC-
7
100Ω
20
Terminated
8
SerTFG-
21
SerTFG+
8
NC
21
NC
9
CC1-
(Trigger IN -)
22
CC1+
(Trigger IN +)
9
NC
22
NC
10
NC (CC2+)
23
NC (CC2-)
10
NC
23
NC
11
NC (CC3-)
24
NC (CC3+)
11
NC
24
NC
12
NC (CC4+)
25
NC (CC4-)
12
NC
25
NC
13
GND
26
GND
13
GND
26
NC

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
13
LVAL Output
296 CLK
Video Output
DVAL Output
FVAL Output
1920CLK
1624CLK
CLK 72 MHz
1 CLK
296 CLK
7. Timing Chart
7.1. Horizontal Synchronous Signals Timing
7.2. Vertical Synchronous Signals Timing
LVAL Output
Video Output
DVAL Output
FVAL Output
1 2 3 4 5 6 7 8 9 10 11 12 28 30 31
(CCD Read Out Signal)
9H(V Sync)
28H
19H(Back proch)
Total = 1252H
125
2
125
129 32 33 34 35 36 37 38 39 40
125
2
125
11 2 3
1200H(Active Line)
24H
(Active Line Margin)
12
28
122
9
122
6
122
7
122
5
122
4
122
2
122
3
122
1
122
0
121
9

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
14
LVAL Output
Video Output
FVAL Output
DVAL Output
19H
(CCD Read
Out Signal )
1 9
29 1252
1224 H
1243H
(Trigger Input)
Exposure Time
( Trigger Input )
(Sub Pulse )
(CCD Read Out Signal)
Delay ( Fixed)
SP Output
(Exposure Signal)
3
CLK
66
CLK
0.96μs
nHD × 27.67μs +18.53μs
a
b
a
b
7.3. Fixed Trigger Shutter Mode
□Trigger operation is CLK sync, V-Sync Reset.
Delay time, from detecting the trigger edge to starting exposure, is 0.96μs .
□Trigger input can be accepted even when the camera is outputting video signals.
However, a shutter timing, to start the next video output before completion of transferring video
output for the prior signals, cannot be worked. To input trigger signals when the camera is
outputting video signals for the prior signals, it shall be synchronized with the down edge of
camera LVAL output.
□Trigger input during the execution of exposure (exposure time) shall be ignored.
(Refer to the “G”below.)
(E)
（Ｂ）
（Ｂ）
(F)
Trigger invalid
(E)
（Ｆ）
(F) (G)
✖
Video Output
(Trigger Input )
DVAL Output
SP Output
(Exposure Signal) Exposure Time ( Register Set Value) Exposure Time
✖
( Exposure Time )
(Register Set Value)

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
15
LVAL Output
Video Output
FVAL Output
DVAL Output
19H
(CCD Read
Out Signal)
Exposure Time
1 9
29 1252
1224H
1243H
(Trigger Input)
(Trigger Input)
(Sub Pulse)
(CCD Read Out Signal)
Delay(Fixed)
SP Output
(Exposure Signal)
3
CLK
66
CLK
953
CLK
450
CLK
0.96μs
19.49μs
a
b
a
b
Delay(Fixed)
7.4. Pulse Width Trigger Shutter Mode
□Trigger operation is CLK sync, V-Sync Reset.
Delay time, from detecting the trigger edge to starting exposure, is 0.96μs .
Delay time, from detecting the trigger edge to completing exposure, is 19.49μs.
□Trigger input can be accepted even when the camera is outputting video signals.
However, a shutter timing, to start the next video output before completion of transferring video
output for the prior signals, cannot be worked. Please refer to the “C”below.
To input trigger signals when the camera is outputting video signals for the prior signals, it shall
be synchronized with the down edge of camera LVAL output.
(A)
(A) (B)
（Ｂ）
(B)
(C)
（Ｂ）
(D)
(D)
Trigger invalid
✖
Video Output
(Trigger Input)
DVAL Output
SP Output
(Exposure Signal)
Exposure Time
(Pulse Width)
Exposure Time
(Pulse Width)
Exposure Time
( Pulse Width )
(Video Output (C))
✖
(Exposure Time)

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
16
FVAL Output
(Normal Scan)
9H
Video Output
(Normal Scan)
1252 H
VIDEO Output
(Partial Scan)
FVAL Output
(Partial Scan)
9H
19H
Total Line ( Address021&022 ) + 1H
1224 H
Y Offset
19 H + Starting Position
(Address016&017)
Effective Line
(Address019&020) ×3 +3H
High Speed
Transmit Period
High Speed
Transmit Period
8. Partial Scan Mode Details
Capturing start position and capturing width can be set by 3H via LAN.
Reading out position register (Address 016&017) : 0(0 H)～407(1221 H) 3 H/step
Effective line register (Address 019&020) : 0(3 H)～407(1224 H) 3 H/step
Total line register (Address 021&022) : 435 H + (Effective Line register ×2) + 2 (Read Only)
Note: Reading out position and effective lines shall meet the following condition.
Reading out position register + Effective line register =< 407
Otherwise, the value, 407 –reading out position register, will be set to the effective line register.
<Example 1> Conditions: Reading out position register (Address 016 & 017) = 000
Effective line register
(Address 019&020)
Effective Lines
Total Line register
+1H
Frame rate
0
3 H
438 H
86 fps
・
・
・
・
159
480 H
756 H
50 fps・
・
・
・
・
255
768 H
948 H
40 fps
・
・
・
・
341
1026 H
1120 H
33 fps
・
・
・
・
407
1224
1252 H
30 fps

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
17
9. Remote Interface Function
Through serial port of camera link connector, the camera can be controlled.
(1) The settings for RS-232C
(2) Control code
・The total control code is 14 bits, which conforms to ASCII code.
・The control code consists of camera No. process code, remote controller address, remote
controller data, and CR. Execute Read/Write through PC, and the camera will reply the data.
1
2
3
4
5
6
7th Byte
8
9
10
11
12
13
14
Camera No.
Process code
Remote controller
address
Remote controller
data
CR
000000: fixed
“R”Read mode
“W”Write mode
“C”Camera mode
Please refer to the
address table of
Section 5.,
Function Settings.
000～255
0 Dh
00EEEE: 4digits error code
“X”error response
0 0 0
0 0 0
Camera No. is fixed with 6 bite numerical strings, “000000”.
Process code
Input any one of R, W, or C to the process code.
R (read mode) is to read the data of remote controller address.
Please be noted to set any dummy data (000～255) to 11th ～13th, since a command shall consists
of 14 bytes.
W (write mode) is to write the data to the remote controller address.
Please be noted that the data cannot be saved into EEPROM of the camera.
(Reboot the camera, and the data is reset to the initial setting.)
To save the data into EEPROM, please refer to Section 5., Function Settings.
C is the code to send the data back from the camera.
Note: Do not set code C when sending the data from PC side.
Baud rate
:9600bps
Data
:8bit
Stop bit
:1bit
Parity
:None
XOn/XOff
:Not controlled

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
18
X is the code to respond when the camera side detects an error.
Error details can be checked with 4 digits, 3rd to 6th bytes.
0101 Address value error
0102 Command error
0103 Data value error
0104 Data length error (over 14 byte)
Remote controller address
Note: Do not write the data into the address other than specified, since it may cause the
damages or malfunction of the camera.
Remote controller data
Set the decimal number (000～255) for the remote controller data. Please be noted to set any
dummy data at read control mode.
CR
Be sure to input “CR”to confirm the end of the command.
※Note: When setting the data with 2 Byte, High Byte shall be set first, then Low Byte to the next.
The camera rewrites the internal resister when receiving Low Byte.
10. Initial Settings
Function
Address
Data
Gain
001
0:
0
dB
E-Shutter
002
0:
1/30s(Off)
White Balance
003
1:
3200K
Trigger Mode
004
0:
Normal Trigger Mode (Trigger Mode Off)
Trigger Polarity
011
0:
Positive Input
Trigger Input
012
0:
Camera Link (CC1) Input
Output Data Select
013
0:
24bit RGB Output Data
Gamma Mode
014
0:
Gamma OFF (1.0)
Partial Scan Mode
015
0:
Full Frame Scan Mode
Partial Scan Total Line
021&022
1251:
Read Only

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
19
55
55
Datum Plane B
Inclination of optical
axis to datum plane A
1.5 60 6.3
Datum Plane A
Inclination of optical axis
to datum plane B
Datum Plane A
910-010-00-00
*)Dimensions from datum plane A to the center of the lens mount
The center of effective pixels shall
be within 0.6 phai to the center of
lens mount.
Inclination of effective pixels theta to datum plane A.
Theta shall be under ±0.5°
(Unit:mm)
90°±0.2°
Under±0.5°
Theta=±0.5°
27.5±0.3(*)
11. CCD Optical Axis Accuracy

VCC-F52U25CL Rev.900-668-31-01
©2010 CIS Corporation. All rights reserved.
20
28±0.1
55
28±0.1
55
2 MEGA PIXEL
3CCD
1.5 60 6.3
Product Name
Label Position
35±0.1
4.5±0.1 52
CL1
CL2
DC IN
999-502-00-02
(Unit :mm)
F 29 0
-0.05
4-M3
Depth 4
CMount(*)
4-M3
Depth 4
*) C Mount screws comply with ANSI/ASME B1.1, 1-32U (2B).
*) Screw length from C mount lens surface shall be under 4.5mm. And protruding portion shall be less than 4.5mm.
12. Dimensions