Cisco NCS 1004 Manual

Hardware Installation Guide for Cisco NCS 1004
First Published: 2019-08-30
Last Modified: 2020-04-21
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of
the UNIX operating system. All rights reserved. Copyright ©1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.
CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.
All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version.
Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL:
http://www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship
between Cisco and any other company. (1721R)
©2020 Cisco Systems, Inc. All rights reserved.

CHAPTER 1
Cisco NCS 1004 Overview
This chapter provides an overview for Cisco NCS 1004.
•Cisco NCS 1004 Overview , on page 1
•Supported Pluggables, on page 3
Cisco NCS 1004 Overview
The Cisco NCS 1004 chassis is a 2RU chassis that delivers a universal transponder solution which provides
excellent performance for metro, long-haul and submarine applications.
The Cisco NCS 1004 has the following modules:
• Removable controller
• Two replaceable power supply units (PSU)
• Three replaceable fan units
• Four line card slots
For more information about the Cisco NCS 1004 chassis, the NCS1K4-1.2T-K9 ( or 1.2 Tbps) C-band line
card, see Cisco NCS 1004 datasheet.
"1.2T" refers to the NCS1K4-1.2T-K9 C-band line card.
Note
The controller is on the front side. The PSUs and the fan units are on the rear side of the chassis. The line
cards can be inserted in to the four slots as shown in the following figure.
Hardware Installation Guide for Cisco NCS 1004
1

Figure 1: NCS 1004 Front View
Controller2
The slots for the PSUs and fan units are indicated in the following figure.
Figure 2: NCS 1004 Rear View
Power Supply Units (Slots 0 and 1)1
Fan Units (Slots 0,1,2)2
Both the power supply modules should be AC or DC. Mixed configuration is not allowed.
Cisco NCS 1004 has a front to back airflow scheme. The air inlet is at the front side of the chassis and the
exhaust is on the rear side. Ensure that the airflow is not obstructed or impeded by any object as it may lead
to reduced airflow in the system, causing components to operate at a higher temperature.
Hardware Installation Guide for Cisco NCS 1004
2
Cisco NCS 1004 Overview
Cisco NCS 1004 Overview

Figure 3: Airflow in NCS 1004
Class 1M Laser Product Label
The Class 1M Laser Product label is shown in the following figure.
Figure 4: Class 1M Laser Product Label
Supported Pluggables
The following pluggables are supported on NCS 1004.
• QSFP-100G-SR4-S
• QSFP-100G-CWDM4-S
Hardware Installation Guide for Cisco NCS 1004
3
Cisco NCS 1004 Overview
Supported Pluggables

• QSFP-100G-SM-SR
• QSFP-100G-AOC-1M
• QSFP-100G-AOC-3M
• QSFP-100G-AOC-10M
• QSFP-100G-LR4-S
• QSFP-100G-CU1M
• QSFP-100G-CU2M
• QSFP-100G-CU3M
• QSFP-100G-CU5M
• QSFP28-FR
Hardware Installation Guide for Cisco NCS 1004
4
Cisco NCS 1004 Overview
Supported Pluggables

CHAPTER 2
Safety Guidelines
Before you perform any procedure in this publication, you must review the safety guidelines in this section
to avoid injuring yourself or damaging the equipment. Note that this section contains guidelines, and does
not include every potentially hazardous situation. During any installation procedure, always use caution and
common sense.
Review the complete list of safety warnings available at Regulatory Compliance and Safety Information for
Cisco NCS 1004 Series.
•Standard Warning Statements, on page 5
•General Safety Guidelines for Personal Safety and Equipment Protection, on page 6
•Safety Precaution for Module Installation and Removal, on page 6
•Safety with Electricity, on page 7
•Power Connection Guidelines , on page 7
•Safety Precaution for Energy Hazard, on page 8
•Safety Precaution for Laser Radiation, on page 8
•Prevent Electrostatic Discharge Damage , on page 9
Standard Warning Statements
This unit is intended for installation in restricted access areas. A restricted access area can be accessed
only by using a special tool, lock and key, or other means of security.Statement 1017
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning
Hazardous voltage or energy may be present on power terminals. Always replace cover when terminals
are not in service. Be sure uninsulated conductors are not accessible when cover is in place. Statement
1086
Warning
Hardware Installation Guide for Cisco NCS 1004
5

Mount the device on a rack that is permanently affixed to the building.Statement 1049
Warning
Ultimatedisposalofthisproductmust be handled according to all national laws and regulations.Statement
1040
Warning
General Safety Guidelines for Personal Safety and Equipment
Protection
Follow these safety guidelines:
• Never attempt to lift an object that might be too heavy for you to lift by yourself.
• Always unplug power cables when performing maintenance or working on the chassis, unless the
replacement part is hot swappable and designed for online insertion and removal (OIR).
• Keep the work area clear and dust free during and after installation.
• Keep tools and chassis components away from walkways and equipment rack aisles.
• Do not wear loose clothing, jewelry (including rings and chains), or other items that could get caught in
the equipment.
• Fasten your tie or scarf and sleeves.
• Operate Cisco equipment safely by using it in accordance with its electrical ratings and product usage
instructions.
• Do not work alone if potentially hazardous conditions exist.
• Ensure that the installation of the router is in compliance with national and local electrical codes: in the
United States, National Fire Protection Association (NFPA) 70, United States National Electrical Code;
in Canada, Canadian Electrical Code, part I, CSA C22.1; in other countries, International Electrotechnical
Commission (IEC) 364, part 1 through part 7.
Safety Precaution for Module Installation and Removal
Ensure to observe the following safety precautions when you are working with the chassis modules.
Invisible laser radiations present.Statement 1016
Warning
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams
or view directly with optical instruments.Statement 1051
Warning
Hardware Installation Guide for Cisco NCS 1004
6
Safety Guidelines
General Safety Guidelines for Personal Safety and Equipment Protection

Safety with Electricity
Before working on a chassis or with power supplies, unplug the power cord on AC units. Disconnect
the power at the circuit breaker on DC units.Statement 12
Warning
Beforeworkingon equipment that is connected to powerlines,removejewelry(includingrings,necklaces,
and watches). Metal objects heat up when connected to power and ground and can cause serious burns
or weld the metal object to the terminals.Statement 43
Warning
Avoid using or servicing any equipment that has outdoor connections during an electrical storm. There
may be a risk of electric shock from lightning. Statement 1088
Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority
or an electrician if you are uncertain that suitable grounding is available.Statement 1024
Warning
This unit may have more than one power supply connection. All connections must be removed to
de-energize the unit.Statement 1028
Warning
Wheninstalling or replacingtheunit, ensurethegroundconnection firstand disconnected last. Statement
1046
Warning
Thisequipment is intended to be groundedtocomply with emission and immunity requirements.Ensure
that the switch functional ground lug is connected to earth ground during normal use. Statement 1064
Warning
Power Connection Guidelines
Check the power at your site to ensure you are receiving clean power (free of spikes and noise).
Ensure to observe the following safety guidelines while connecting the device power supplies.
Hardware Installation Guide for Cisco NCS 1004
7
Safety Guidelines
Safety with Electricity

Never defeat the ground conductor or operate the equipment in the absence of a suitably installed
ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are
uncertain that suitable grounding is available. Statement 1024
Warning
This product requires short-circuit (overcurrent) protection, to be provided as part of the building
installation. Install only in accordance with national and local wiring regulations. Statement 1045
Warning
Safety Precaution for Energy Hazard
Do not reach into a vacant slot when installing or removing a module. Exposed circuitry is an energy
hazard.Statement 206
Warning
The Cisco NCS 1004 can be configured for a DC power source. Do not touch terminals with body parts or
conductive objects while they are energized.
Safety Precaution for Laser Radiation
Cisco NCS 1004 is classified as Hazard Level 1M as per IEC 60825-2, since it includes embedded Class 1
or Class 1M Laser sources.
Statement 291
Warning
Invisible laser radiations present.Statement 1016
Warning
Hardware Installation Guide for Cisco NCS 1004
8
Safety Guidelines
Safety Precaution for Energy Hazard

Figure 5: Class 1M Laser Product Label
Prevent Electrostatic Discharge Damage
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD may occur when
electronic printed circuit cards are improperly handled and can cause complete or intermittent failures. When
removing and replacing modules, always follow these ESD prevention procedures:
• Ensure that the device chassis is electrically connected to earth ground.
• Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact.
• Handle components by only their handles or edges; do not touch the printed circuit boards or connectors.
• Avoid contact between the printed circuit boards and clothing. The wrist strap only protects components
from ESD voltages on the body; ESD voltages on clothing can still cause damage.
Hardware Installation Guide for Cisco NCS 1004
9
Safety Guidelines
Prevent Electrostatic Discharge Damage

Hardware Installation Guide for Cisco NCS 1004
10
Safety Guidelines
Prevent Electrostatic Discharge Damage

CHAPTER 3
Prepare to Install Cisco NCS 1004
This chapter explains how to prepare for the Cisco NCS 1004 installation.
•Shipping and Receiving, on page 11
•Unpack and Verify Cisco NCS 1004, on page 16
Shipping and Receiving
The chassis is shipped in one of the following ways:
• Chassis with filler cards and line cards— you receive the chassis with preinstalled line cards (based on
the number of line cards you have ordered) and the rest of the line card slots have filler cards. If you
have preordered four line cards, then, the chassis does not contain any filler cards. There are four fiber
management brackets in the package, for each of the line card or filler cards preinstalled in the chassis.
The controller and the three fan units are also preinstalled. The other items available in the same package
(with the chassis) are:
• Accessory kit, that has all the installation hardware.
• Two PSUs - AC or DC. Installation of PSUs is discussed in the Install Cisco NCS 1004 Modules
chapter.
AC chassis - while ordering for an AC chassis, select the power cable. Based on your choice (NEMA
or CEE), you get a pair of 90 degree and straight cables for each PSU. All the AC cables are 4.25
m long.
Table 1: Power cables for the chassis
CPNP2 ConnectorP1 ConnectorType of Cable
72-101432-01IEC 60320 – C21NEMA L6-20PStraight cable
72-101434-01IEC 60320 – C21CEE 7/7 (Europe)
72-101425-01
IEC 60320 – C21CEE 7/7 (Europe)90-degree cable
37-1138-01IEC 60320 – C21NEMA L6-20P
Hardware Installation Guide for Cisco NCS 1004
11

Figure 6: 90-degree Cable (CEE 7/7)
Figure 7: 90-degree Cable (NEMA L6-20P)
Figure 8: Straight Cable (NEMA L6-20P)
Hardware Installation Guide for Cisco NCS 1004
12
Prepare to Install Cisco NCS 1004
Shipping and Receiving

Figure 9: Straight Cable (CEE 7/7)
The 90deg cable is used only for ETSI racks to maintain a footprint of 600 mm.
Note
DC chassis - when you order for a DC chassis, you get four power lugs for each PSU (a pair of
90-degree and a pair of 180-degree lugs). 180-degree lugs are used for ETSI racks to maintain a
footprint of 600 mm.
Figure 10: DC Power Cable Lug (180-degree)
Hardware Installation Guide for Cisco NCS 1004
13
Prepare to Install Cisco NCS 1004
Shipping and Receiving

Figure 11: DC Power Cable Lug (90-degree)
Figure 12: Breakout Cable
The breakout cable is used only for ETSI racks to maintain a footprint of 600
mm.
Note
Table 2: Specifications of Breakout Cables
Overall Length (in m)MPNCPNPID
05 plus or minus 0.30BCJ7F3FM005CSO00872-101758-01ONS-4X10-MMCBL-5=
10 plus or minus 0.30BCJ7F3FM010CSO00872-101759-01ONS-4X10-MMCBL-10=
Hardware Installation Guide for Cisco NCS 1004
14
Prepare to Install Cisco NCS 1004
Shipping and Receiving

Overall Length (in m)MPNCPNPID
20 plus or minus 0.60BCJ7F3FM020CSO00872-101760-01ONS-4X10-MMCBL-20=
Figure 13: Chassis shipped with Line Cards
• Chassis with only filler cards— you receive the chassis with four filler cards in the line card slots. There
are four fiber management brackets in the package, for each of the filler cards. Each line card ordered
as a spare item is shipped separately and the extra fiber management bracket (for the line card) is available
in the line card package. Only the accessory kit is available with the chassis (in the same package). You
must order all the other modules (fan units, controller, PSUs) separately.
For installation procedures of the modules, see Install Cisco NCS 1004 Modules chapter.
Hardware Installation Guide for Cisco NCS 1004
15
Prepare to Install Cisco NCS 1004
Shipping and Receiving

Figure 14: Chassis shipped with Filler Cards
Unpack and Verify Cisco NCS 1004
This procedure enables the you to unpack and check if all the chassis modules that are required for installation
have been shipped.
Step 1 When you receive Cisco NCS 1004 equipment at the installation site, open the top of the box.
Step 2 Remove accessories and foam inserts from the box. The box contains Cisco NCS 1004 and other items needed for
installation.
Step 3 To remove the chassis from the packaging, grasp the side of the chassis and lift it out of the box.
Use these lifting guidelines to avoid injury to yourself or damage to the equipment:
• Do not lift equipment alone; have another person help you to lift the equipment.
Hardware Installation Guide for Cisco NCS 1004
16
Prepare to Install Cisco NCS 1004
Unpack and Verify Cisco NCS 1004

Figure 15: Lifting the NCS 1004
A fully loaded chassis can weigh as much as 28.7 kgs (63.3 lbs).
• Ensure that your footing is solid; balance the weight of the object between your feet.
• Lift the equipment slowly; never move suddenly or twist your body as you lift.
• Keep your back straight and lift with your legs, not your back. When bending down to lift equipment, bend at the
knees (not at the waist), to reduce the strain on your lower back muscles.
Step 4 Verify the following:
• The Cisco NCS 1004 is not damaged. Check for a scratch, bend, discoloration or deformation on the Cisco NCS
1004 chassis.
• The modules that are shipped with the chassis or separately are not damaged.
Step 5 If there is any damage to the chassis or the modules, call your Cisco sales engineer for a replacement.
Hardware Installation Guide for Cisco NCS 1004
17
Prepare to Install Cisco NCS 1004
Unpack and Verify Cisco NCS 1004

Hardware Installation Guide for Cisco NCS 1004
18
Prepare to Install Cisco NCS 1004
Unpack and Verify Cisco NCS 1004