Cisco Firepower 1010 FPR1010-NGFW-K9 Manual

Cisco Firepower 1010 Hardware Installation Guide
First Published: 2019-07-24
Last Modified: 2021-08-17
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of
the UNIX operating system. All rights reserved. Copyright ©1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.
CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.
All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version.
Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL:
https://www.cisco.com/c/en/us/about/legal/trademarks.html. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a
partnership relationship between Cisco and any other company. (1721R)
©2019-2021 Cisco Systems, Inc. All rights reserved.

CONTENTS
Overview 1
CHAPTER 1
Features 1
Package Contents 5
QR Code Sticker 5
Serial Number Location 6
Front Panel 7
Rear Panel 7
Status LEDs 8
Hardware Specifications 11
Product ID Numbers 12
Power Cord Specifications 12
Installation Preparation 19
CHAPTER 2
Installation Warnings 19
Position the Chassis 22
Safety Recommendations 23
Maintain Safety with Electricity 23
Prevent ESD Damage 24
Site Environment 24
Site Considerations 24
Power Supply Considerations 25
Rack Configuration Considerations 25
Mount the Chassis 27
CHAPTER 3
Unpack and Inspect the Chassis 27
Desktop-Mount the Chassis 28
Cisco Firepower 1010 Hardware Installation Guide
iii

Wall-Mount the Chassis 28
Rack-Mount the Chassis 31
Connect to the Console Port 37
CHAPTER 4
Connect to the Console Port with Microsoft Windows 37
Connect to the Console Port with Mac OS X 39
Connect to the Console Port with Linux 39
Installation, Maintenance, and Upgrade 41
CHAPTER 5
Install the FIPS Opacity Shield 41
Cisco Firepower 1010 Hardware Installation Guide
iv
Contents

CHAPTER 1
Overview
•Features, on page 1
•Package Contents, on page 5
•QR Code Sticker, on page 5
•Serial Number Location, on page 6
•Front Panel, on page 7
•Rear Panel, on page 7
•Status LEDs, on page 8
•Hardware Specifications, on page 11
•Product ID Numbers, on page 12
•Power Cord Specifications, on page 12
Features
The Cisco Firepower 1010 security appliance is an NGFW desktop product in the Cisco Firepower family of
devices with Power over Ethernet (PoE+) and L2 switch support.
The PoE+ and L2 switch features are supported starting with Firepower Threat Defense (FTD) Version 6.5
and ASA Version 9.13.
Note
See the Cisco Firepower Compatibility Guide, which provides Cisco Firepower software and hardware
compatibility, including operating system and hosting environment requirements, for each supported Firepower
version.
See Product ID Numbers, on page 12 for a list of the product IDs (PIDs) associated with the Firepower 1010.
The following figure shows the Cisco Firepower 1010.
Cisco Firepower 1010 Hardware Installation Guide
1

Figure 1: Cisco Firepower 1010
The following table lists the features for the Firepower 1010.
Table 1: Firepower 1010 Features
DescriptionFeature
• Common Criteria (CC) on FTD 6.4.xand FX-OS 2.6.x
• Federal Information Processing Standards (FIPS) 140-2 on FTD 6.4.xand FX-OS
2.6.x
• Department of Defense Information Network Approved Product List (DoDIN APL)
• US Government Compliance for IPv6 (USGv6) on FTD 6.4.x
See the "Security Certifications Compliance" topic in the "Appliance Platform Settings"
chapter in the Firepower Management Center Configuration Guide, Version 6.7 for the
instructions on how to enable security certifications compliance.
Security
standards
certifications
1 RUForm factor
Desktop mount
Wall mount (Cisco part number 69-100647-01)
Rack mount (Cisco part number 69-100648-01)
Mounting
Side-to-side
No fan
Airflow
One 4-core Intel CPUProcessor
8-GB DDR4 DRAMMemory
8 GB (internal)Boot partition
Marvell SOHO 88E6390
First supported in Firepower Version 6.5 and ASA Version 9.13.
Note
L2 switch
One Gigabit Ethernet RJ-45 10/100/1000 BaseT
Restricted to network management access; connect with an RJ-45 cable
Management
port
Cisco Firepower 1010 Hardware Installation Guide
2
Overview
Features

One RJ-45
Use to access management through an external system
Console port
One USB Mini B
Use to access management through an external system
USB Mini B
port
One USB 3.0 Type A
Use to attach an external device such as storage
USB port
Eight Gigabit Ethernet RJ-45 10/100/1000 BaseT
Each RJ-45 (8P8C) copper port supports auto Medium Dependent Interface Crossover
(MDI/X) as well as auto-negotiation for interface speed, duplex, and other negotiated
parameters, and are MDI/X-compliant.
The ports are numbered (from top to bottom, left to right) 1, 2, 3, 4, 5, 6, 7, 8. Each port
includes a pair of LEDs, one each for connection status and link status. The ports are
named and numbered Gigabit Ethernet 1/1 through Gigabit Ethernet 1/8.
You can use ports 7 and 8 as PoE+ ports. PoE+ is first supported in Firepower
Version 6.5 and ASA Version 9.13.
Note
Network ports
Ports 7 and 8 are PoE+ ports; first supported in Firepower Version 6.5 and ASA
Version 9.13.
Note
PoE+ controller
card
Accepts a standard Kensington T-bar locking mechanism for securing the chassisLock slot
A small recessed button that if pressed for longer than three seconds resets the chassis to
its default state following the next reboot. Configuration variables are reset to factory
default, but the flash is not erased and no files are removed.
Reset button
No
System power is controlled by the power cord; there is no power button. To shut down
the Firepower 1010, remove the AC power supply.
Power switch
The chassis is powered on when you plug in the AC power supply.Power cord
socket
One external AC power supply
The power supply has a total of 115 W of power. There is 55 W of +12-V system power
and 60 W of -53.5-V PoE+ power.
PoE+ is first supported in Firepower Version 6.5 and ASA Version 9.13.
Note
Use the power supply (part number 341-100765-01) that shipped with the
chassis. It supports PoE+.
Note
AC power
supply
Cisco Firepower 1010 Hardware Installation Guide
3
Overview
Features

One 200-GB M.2 SATA SSD drive
The drive is used by the software; there is no user access to the drive.
The drive is not field-replaceable; you must return the chassis to Cisco for drive
replacement.
Storage
Four rubber feet on the bottom of the chassis
The rubber feet are needed for proper cooling. Do not remove them.
Note
Rubber feet
Console Ports
The Firepower 1010 has two external console ports, a standard RJ-45 port and a USB Mini B serial port.
Only one console port can be active at a time. When a cable is plugged into the USB console port, the
RJ-45 port becomes inactive. Conversely, when the USB cable is removed from the USB port, the RJ-45
port becomes active. The console ports do not have any hardware flow control. You can use the CLI to
configure the chassis through either serial console port by using a terminal server or a terminal emulation
program on a computer.
• RJ-45 (8P8C) port—Supports RS-232 signaling to an internal UART controller. The RJ-45 console
port does not support a remote dial-in modem. You can use a standard management cable (Cisco
part number 72-3383-01) to convert the RJ45-to-DB9 connection if necessary.
•USB Mini B port—Lets you connect to a USB port on an external computer. For Linux and Macintosh
systems, no special driver is required. For Windows systems, you must download and install a USB
driver (available on software.cisco.com). You can plug and unplug the USB cable from the console
port without affecting Windows HyperTerminal operations. We recommend shielded USB cables
with properly terminated shields. Baud rates for the USB console port are 1200, 2400, 4800, 9600,
19200, 38400, 57600, and 115200 bps.
For Windows operating systems, you must install a Cisco Windows USB Console Driver on any PC
connected to the console port before using the USB console port. See Connect to the Console Port with
Microsoft Windows, on page 37 for information on installing the driver.
Note
External Flash Storage
The chassis contains a standard USB Type A port that you can use to attach an external device. The USB
port can provide output power of 5 V and up to a maximum of 1A (5 USB power units).
• External USB drive (optional)—You can use the external USB Type A port to attach a data-storage
device. The external USB drive identifier is disk1. When the chassis is powered on, a connected
USB drive is mounted as disk1 and is available for you to use. Additionally, the file-system
commands that are available to disk0 are also available to disk1, including copy,format,delete,
mkdir,pwd,cd, and so on.
• FAT-32 File System—The Firepower 1010 only supports FAT-32-formatted file systems for the
external USB drive. If you insert an external USB drive that is not in FAT-32 format, the system
mounting process fails, and you receive an error message. You can enter the command format
disk1: to format the partition to FAT-32 and mount the partition to disk1 again; however, data might
be lost.
Cisco Firepower 1010 Hardware Installation Guide
4
Overview
Features

Package Contents
The following figure shows the package contents for the Firepower 1010. Note that the contents are subject
to change and your exact contents might contain additional or fewer items.
Figure 2: Firepower 1010 Package Contents
USB console cable (Type A to Mini Type B)
Part number 37-19770-01
2Chassis1
Power supply4Power cord
See Power Cord Specifications, on page 12 for
a list of the approved power cords.
3
—Cisco Firepower 1010
This document has a URL pointing to the
hardware installation guide, a URL pointing to
the regulatory and safety guide, and a QR code
and URL pointing to the Getting Started Guide.
5
QR Code Sticker
The QR code sticker on the front panel of the chassis points to the Firepower Easy Deployment Guide for
Cisco Firepower 1000 or 2100 Firewalls that explains low touch provisioning (LTP). LTP allows anyone to
connect a new Firepower 1010 to a network so that the IT department can onboard the device to CDO and
configure it remotely. CDO supports Firepower Threat Defense (FTD) version 6.7 and later.
The following figure shows the QR code sticker.
Cisco Firepower 1010 Hardware Installation Guide
5
Overview
Package Contents

Figure 3: QR Code Sticker
The following figure shows the placement of the QR code sticker on the front panel of the chassis.
Figure 4: Firepower 1010 QR Code Sticker
—QR code sticker1
Serial Number Location
You can view the serial number and additional model information on the compliance label located on the
bottom of the chassis. The following figure shows a sample compliance label.
Cisco Firepower 1010 Hardware Installation Guide
6
Overview
Serial Number Location

Figure 5: Compliance Label on the Chassis
Front Panel
The following figure shows the front panel of the Firepower 1010. Note that there are no connectors or LEDs
on the front panel.
Figure 6: Firepower 1010 Front Panel
Rear Panel
The following figure shows the rear panel of the Firepower 1010. See Status LEDs, on page 8 for a description
of the LEDs.
Cisco Firepower 1010 Hardware Installation Guide
7
Overview
Front Panel

Figure 7: Firepower 1010 Rear Panel
Management port2Status LEDs1
Power cord socket4Lock slot3
Console port6Network data ports5
USB Type A port8USB Mini B port7
Rubber feet10Reset button9
Status LEDs
Facing the rear of the chassis, the LEDs are located on the top left edge (facing the front of the chassis, they
are in the back right corner of the top). The network port LEDs are at the top sides of each network port.
The following figure shows the status LEDs on the rear panel and on the cover of the chassis.
Cisco Firepower 1010 Hardware Installation Guide
8
Overview
Status LEDs

Figure 8: Status LEDs
Power, Status, and Active LEDs on top of chassis2Power, Status, and Active LEDs on rear of chassis1
The following figure shows all of the LEDs on the rear panel of the Firepower 1010 and describes their states.
Figure 9: Rear Panel LEDs
Cisco Firepower 1010 Hardware Installation Guide
9
Overview
Status LEDs

Status
System operating status:
• Off—System has not booted up yet.
• Green, flashing quickly—System is booting
up.
• Green—Normal system function.
• Amber—Critical alarm indicating one or
more of the following:
•Major failure of a hardware or software
component.
• Over-temperature condition.
• Power voltage outside the tolerance
range.
• Green, flashing slowly (twice in 5
seconds)—Cloud connected.
Cisco Defense Orchestrator
(CDO) is valid for FTD 6.7 and
later.
Note
• Green and amber, flashing—Cloud
connection failure.
• Green—Cloud disconnected.
The CDO LED pattern applies to low
touch provisioning (LTP). See the
Firepower Easy Deployment Guide for
Cisco Firepower 1000 or 2100
Firewalls for more information.
Note
2Power
Power supply status:
• Off —Power supply off.
• Green—Power supply on.
1
Network
Status of the network ports.
Link status (L):
• Off—No link, or port is not in use.
• Green—Link established.
• Green, flashing—Link activity.
4Active
Status of the failover pair:
• Off— Failover is not operational.
• Green—Failover pair operating normally.
The LED is green always unless the chassis
in a high availability pair.
• Amber—When the chassis is in a high
availability pair, the LED is amber for the
standby unit.
3
Cisco Firepower 1010 Hardware Installation Guide
10
Overview
Status LEDs

—Network
Status of the network ports.
Connection-speed status (S):
• Green, flashing—One flash every three
seconds = 10 Mbps.
• Green, flashing—Two rapid flashes = 100
Mbps.
•Green, flashing—Three rapid flashes = 1000
Mbps.
5
Hardware Specifications
The following table contains hardware specifications for the Firepower 1010.
Table 2: Firepower 1010 Hardware Specifications
1.82 x 7.85 x 8.07 inches (4.62 x 19.94 x 20.50 cm)Dimensions (H x W x D)
3 lb (1.36 kg)Weight
30 W
Not including any PoE devices connected to the chassis. 55 W is the maximum
power for the power supply.
PoE+ is first supported in FTD Version 6.5.
Note
Use the power supply (part number 341-100765-01) that shipped with
the chassis. It supports PoE+.
Note
System power
Operating: 32 to 104⁰F (0 to 40⁰C)
Derate the maximum operating temperature 1.5⁰ C per 1000 ft above sea level.
Nonoperating: -13 to 158°F (-25 to 70°C) maximum altitude is 40,000 ft
Temperature
Operating: 90%
Nonoperating: 10 to 90%
Humidity
Operating: 0 to 9843 (3000 m)
Nonoperating: 0 to 15,000 ft (4570 m)
Altitude
0 dBaAcoustic noise
Cisco Firepower 1010 Hardware Installation Guide
11
Overview
Hardware Specifications

Product ID Numbers
The following table lists the field-replaceable PIDs associated with the Firepower 1010. The spare components
are ones that you can order and replace yourself. If any internal components fail, you must get a return material
authorization (RMA) for the entire chassis. See the Cisco Returns Portal for more information.
See the show inventory command in the Cisco Firepower Threat Defense Command Reference or the Cisco
ASA Series Command Reference to display a list of the PIDs for your Firepower 1010.
Note
Table 3: Firepower 1010 PIDs
DescriptionPID
Cisco Firepower 1010 NGFW desktop applianceFPR1010-NGFW-K9
Cisco Firepower 1010 accessory kitFPR1K-DT-ACY-KIT
Cisco Firepower 1010 150-W power supplyFPR1K-DT-PWR-AC
Cisco Firepower 1010 150-W power supply (spare)FPR1K-DT-PWR-AC=
Cisco Firepower 1010 rack-mount kit (spare)FPR1K-DT-RACK-MNT=
Cisco Firepower 1010 wall-mount kit (spare)FPR1K-DT-WALL-MNT=
Cisco Firepower 1010 FIPS kit (spare)FPR1K-DT-FIPS-KIT=
Power Cord Specifications
Each power supply has a separate power cord. Standard power cords or jumper power cords are available for
connection to the security appliance. The jumper power cords for use in racks are available as an optional
alternative to the standard power cords.
If you do not order the optional power cord with the system, you are responsible for selecting the appropriate
power cord for the product. Using a incompatible power cord with this product may result in electrical safety
hazard. Orders delivered to Argentina, Brazil, and Japan must have the appropriate power cord ordered with
the system.
Only the approved power cords or jumper power cords provided with the chassis are supported.
Note
The following power cords are supported.
Cisco Firepower 1010 Hardware Installation Guide
12
Overview
Product ID Numbers

Figure 10: Argentina (CAB-AC-C5-ARG)
Cord set rating: 2.5 A, 250 V2Plug: IRAM 20731
Connector: IEC 60320/C53
Figure 11: Australia (CAB-AC-C5-AUS)
Cord set rating: 2.5 A, 250 V2Plug: AUS 10S31
Connector: IEC 60320/C53
Figure 12: Brazil (CAB-AC-C5-BRA)
Cord set rating: 2.5 A, 250 V2Plug: NBR 141361
Connector: IEC 60320/C53
Cisco Firepower 1010 Hardware Installation Guide
13
Overview
Power Cord Specifications

Figure 13: Canada (CAB-AC-C5)
Cord set rating: 2.5 A, 125 V2Plug: NEMA 5-15P1
Connector: IEC 60320/C53
Figure 14: China (CAB-AC-C5-CHI)
Cord set rating: 2.5 A, 250 V2Plug: GB 2099.11
Connector: IEC 60320/C53
Figure 15: Europe (CAB-AC-C5-EUR)
Cord set rating: 2.5 A, 250 V2Plug: CEE 7 VII1
Connector: IEC 60320/C53
Cisco Firepower 1010 Hardware Installation Guide
14
Overview
Power Cord Specifications

Figure 16: India (CAB-AC-C5-IND)
Cord set rating: 2.5 A, 250 V2Plug: IS 12931
Connector: IEC 60320/C53
Figure 17: Italy (CAB-AC-C5-ITA)
Cord set rating: 2.5 A, 250 V2Plug: CEI 23-06/VII1
Connector: IEC 60320/C53
Figure 18: Japan (CAB-AC-C5-JAP)
Cord set rating: 3 A, 125 V2Plug: JIS C83031
Connector: IEC 60320/C53
Cisco Firepower 1010 Hardware Installation Guide
15
Overview
Power Cord Specifications

Figure 19: Korea (CAB-AC-C5-KOR)
Cord set rating: 3.0 A, 250 V2Plug: KSC 832051
Connector: IEC 60320/C53
Figure 20: South Africa (CAB-AC-C5-SAF)
Cord set rating: 2.5 A, 250 V2Plug: SABS 164-11
Connector: IEC 60320/C53
Figure 21: Switzerland (CAB-AC-C5-SWI)
Cord set rating: 2.5 A, 250 V2Plug: SEV 10111
Connector: IEC 60320/C53
Cisco Firepower 1010 Hardware Installation Guide
16
Overview
Power Cord Specifications