Cisco IAD2430 Series Installation guide

CHAPTER
1-1
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
1
Overview of Cisco IAD2430 Series IADs
This chapter provides a brief description of Cisco IAD2430 series integrated access devices and contains
the following sections:
•Overview, page 1-1
•Cisco IAD2430 Series Deployment, page 1-6
•Interfaces and Service Capabilities, page 1-7
•Physical Description and LEDs, page 1-9
•Specifications, page 1-11
•Software Elements, page 1-12
Overview
The Cisco IAD2430 series integrated access devices (IADs) aggregate multiple channels of data and
voice or fax user-side traffic for transport over single or multiple wide-area network (WAN) uplinks.
Voice or fax traffic is transported by Voice over Internet Protocol (VoIP) or by Voice over Asynchronous
Transfer Mode (VoATM). All platforms support Media Gateway Control Protocol (MGCP), the signaling
protocol H.323, and Session Initiation Protocol (SIP).
Cisco IAD2430 series IADs support the following interfaces:
•10/100BASE-T LAN connection
•T1/E1 port connections
•RJ-21 analog voice interface
•WIC/VIC options
•External/Internal compact flash
Cisco IAD2430 series IADs can be housed in a rack, mounted on a wall, or set on a benchtop surface.
Warning This unit is intended for installation in restricted access areas. A restricted access area can be
accessed only through the use of a special tool, lock and key, or other means by security.
Statement
1017

1-2
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
Chapter 1 Overview of Cisco IAD2430 Series IADs
Overview
Figure 1-1 Cisco IAD2430 Series IADs Front Panel
Figure 1-2 through Figure 1-6 show the basic types of Cisco IAD2430 series chassis as seen from the
cabling side.
Cisco IAD2430-24FXS
The Cisco IAD2430-24FXS provides 24 analog foreign exchange station (FXS) ports with two
10/100BASE-T ports. The chassis has the following interfaces:
•RJ-21 analog voice interface
•Two 10/100BASE-T ports
•External compact flash memory
•AC and DC power inputs
Figure 1-2 Cisco IAD2430-24FXS Chassis
88839
CISCO IAD2400
88838
VG224-24FXS

1-3
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
Chapter 1 Overview of Cisco IAD2430 Series IADs
Overview
Cisco IAD2431-8FXS
THe Cisco IAD2431-8FXS provides eight analog FXS ports, two 10/100BASE-T ports, and one T1/E1
WAN port. The chassis has the following interfaces:
•RJ-21 analog voice interface
•One T1/E1 port
•One 10/100BASE-T port
•One WIC/VIC slot
•External compact flash memory
•AC and DC power inputs
Figure 1-3 Cisco IAD2431-8FXS Chassis
Cisco IAD2431-16FXS
The Cisco IAD2431-16FXS provides sixteen analog FXS ports with two 10/100BASE-T ports and two
T1/E1 WAN ports. The chassis has the following interfaces:
•RJ-21 analog voice interface
•One T1/E1 port
•Two 10/100BASE-T ports
•One WIC/VIC slot
•External compact flash memory
•AC and DC power inputs
Figure 1-4 Cisco IAD2431 -16FXS
88825
IAD2431-8FXS
88826
IAD2431-16FXS

1-4
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
Chapter 1 Overview of Cisco IAD2430 Series IADs
Overview
Cisco IAD2431-1T1E1
The Cisco IAD2431-1T1E1 provides one T1/E1 connection to a PBX, one T1/E1 WAN port, and two
10/100BASE-T ports. The chassis has the following interfaces:
•Two T1/E1 ports
•Two 10/100BASE-T ports
•One WIC/VIC slot
•External compact flash memory
•AC and DC power inputs
Figure 1-5 Cisco IAD2431-1T1E1
Cisco IAD2432-24FXS
The Cisco IAD2432-24FXS provides 24 analog FXS ports, two 10/100BASE-T ports, and two T1/E1
WAN ports. The chassis has the following interfaces:
•RJ-21 analog voice interface
•Two T1/E1 ports
•Two 10/100BASE-T ports
•One WIC/VIC slot
•External compact flash memory
•AC and DC power inputs
Figure 1-6 Cisco IAD2432-24FXS
88827
IAD2431-1T1E1
88824

1-5
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
Chapter 1 Overview of Cisco IAD2430 Series IADs
Overview
Product Serial Number Location for the Cisco IAD2430 Series IADs
The serial number label for the Cisco IAD2430 Series IADs is located on the rear of the chassis, in the
middle-left side. (See Figure 1-14.)
Figure 1-7 Serial Number Locations
Note The serial number for the Cisco IAD2430 Series IADs is 11 characters long.
Configuration Options
The following interface options are available in Cisco IAD2430 series IADs:
103054
IAD2431-8FXS
AAANNNNXXXX
AAANNNNXXXX
Table 1-1 Configuration Options
Cisco IAD2430 Series RJ-211
1. Analog voice interface
T1/E12
2. T1/E1 ports
FE3
3. 10/100BASE-T ports
WIC/VIC4
4. WAN interface card (data); voice interface card (voice)
CF5
5. Compact flash
IAD2430-24FXS yes none 2 n/a external
IAD2431-8FXS yes 1 1 yes external
IAD2431-16FXS yes 1 2 yes external
IAD2431-1T1E1 no 2 2 yes external
IAD2432-24FXS yes 2 2 yes external

1-6
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
Chapter 1 Overview of Cisco IAD2430 Series IADs
Cisco IAD2430 Series Deployment
Cisco IAD2430 Series Deployment
Figure 1-8 through Figure 1-11 show some typical deployment scenarios for Cisco IAD2430 series
integrated access devices.
Figure 1-8 Analog FXS User Interfaces with Metro Ethernet WAN Interface
Figure 1-9 T1/E1 WAN Interface with Analog FXS User Interfaces
IAD
RJ-21
Ethernet
Distribution
panel
88997
Cisco IAD model number:
IAD2430-24FXS
Analog
telephones
IAD
WAN T1 RJ-21
Ethernet
Analog
telephones
Distribution
panel
88998
Cisco IAD model number:
IAD2431-8FXS
IAD2431-16FXS
IAD2432-24FXS

1-7
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
Chapter 1 Overview of Cisco IAD2430 Series IADs
Interfaces and Service Capabilities
Figure 1-10 WAN Interface with Analog FXS and FXO User Interfaces
Figure 1-11 T1/E1 with T1/E1 Interface to PBX
Interfaces and Service Capabilities
The various physical ports and the services supported by each port type are described in Table 1-2.
•Two administrative ports—One console and one auxiliary.
•One or two 10/100BASE-T LAN ports.
•The Cisco IAD2431 and Cisco IAD2432 IADs for T1/E1 WAN interface are equipped with one or
two T1/E1 WAN ports.
•Cisco IAD2430 series IADs for analog voice user interface are equipped with an RJ-21 port for
connection to a distribution panel.
•Cisco IAD2432 IADs for digital voice user interface are equipped with a T1/E1 port for connection
to a PBX.
Caution All Cisco 2430 series IADs are customer premises equipment (CPE) only.
Cisco IAD model number:
Cisco IAD2432-24FXS
with
Cisco VIC2-4FXO interface card
IAD
WAN T1 Multiple FXS and FXO 24 FXS
voice ports
4 FXO
voice ports
Ethernet
Distribution
panel
88996
Analog
telephones
PBX
PBX
88995
IAD
WAN T1 T1
Ethernet
PBX
Cisco IAD model number:
IAD2431-1T1E1

1-8
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
Chapter 1 Overview of Cisco IAD2430 Series IADs
Interfaces and Service Capabilities
Table 1-2 Cisco IAD2430 Series Interfaces and Service Capabilities
Port Interface Configurations Interface To Services Supported Details
Console
Port 0/0
EIA/TIA-232 asynchronous
serial (DCE1)
1. DCE = data communications equipment
ASCII terminal
Personal computer
Local administrative
access
RJ-45 physical interface
Auxiliary
Port 0/1
EIA/TIA-232 asynchronous
serial (DTE2)
2. DTE = data terminal equipment
Modem Remote administrative
access
Data backup
RJ-45 physical interface
Fast Ethernet
Port 0/0, 0/1
10/100BASE-T (802.3) LAN Data RJ-45 physical interface
RJ-21
8, 16, or 24
analog FXS
voice ports
Port 2/0 to
2/23
FXS (loop-start or
ground-start)
Analog phone, fax,
or modem
Network side of key
system
Network side of
analog PBX
Analog voice/fax or
modem
Provides battery
RJ-21 physical interface
8-port FXS, on premise only
16-port FXS, on premise only
24-port FXS, on premise only
T1/E1 trunk
Port 0,1
Channelized T1/E1 WAN
Carrier network
Service types:
•ATM
•Cisco HDLC3
•PPP3
Transport types:
•TDM4trunk
•Leased lines
3. HDLC = High-Level Data Link Control
4. TDM = time-division multiplexing
Built-in CSU/DSU5
T1.403-compliant
RJ-48C/CA81A physical
interface
Supports as many as 24 DS0s
5. CSU/DSU = channel service unit/data service unit
WIC/VIC
slot
S0 (serial)
HDLC-based data WAN
Carrier network
User equipment
Cisco HDLC
PPP6
VoIP over PPP
6. PPP = Point-to-Point Protocol
Physical interfaces:
•EIA/TIA-232
•EIA/TIA-530/530A
•EIA/TIA-449
•V. 3 5
•X.21
CF7Slot 0
7. CF = compact flash memory
Flash memory Compact flash card

1-9
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
Chapter 1 Overview of Cisco IAD2430 Series IADs
Physical Description and LEDs
Physical Description and LEDs
All interface slots and LEDs are on the rear of the chassis.
Figure 1-12 Cisco IAD2430 Series IAD
Figure 1-13 Cisco IAD2400 Series LEDs
1Chassis ground connection 6WIC/VIC slot 11 DC power input1
1. This is not a redundant failover power supply connection. You must use either DC or AC.
2RJ-21 connector 710/100BASE-T port 1 12 On/off switch
3T1/E1 port 1 810/100BASE-T port 0 13 AC power input
4T1/E1 port 0 9AUX port
5Compact flash slot 10 Console port
88828
2
34
789
10
11 12
13
6
5
1
Table 1-3 Cisco 2430 Series IAD LEDs (Cisco 2432-24FXS shown)
No LED/Color Description
1ACT—green
Status—green
Green indicates activity; when any of the 24 voice ports is active in
a call (off hook) or one of the analog ports is in use
Green when accessing IAD
2CF (Slot 0)—green Green when accessing read or write function
95007
1
2
4
3

1-10
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
Chapter 1 Overview of Cisco IAD2430 Series IADs
Physical Description and LEDs
Product Serial Number Location for Cisco IAD2430 Series IADs
The serial number label for the Cisco IAD2430 Series IADs is located on the rear of the chassis, in the
middle-left side. (See Figure 1-14.)
Figure 1-14 Serial Number Locations
Note The serial number for Cisco IAD2430 Series IADs is 11 characters long
Chassis Grounding
Chassis grounding is provided through the power cable, which uses a standard grounding plug. The
chassis is also equipped with two multi 4 x 0.7 screw terminals for chassis grounding. The accessory kit
contains a crimp-type ground lug that attaches to the two screw terminals. For more information, refer
to the “Installing the Ground Connection” section on page 3-11.
Port Numbering Conventions
Port numbering conventions for Cisco IAD2430 series IAD are as follows:
•An external compact flash card is numbered CF 0.
•10/100BASE-T ports are numbered 10/100BASE-T 0/0 and 10/100BASE-T 0/1 from right to left.
•T1/E1 ports are numbered T1 or E1 1/0 and T1 or E1 1/1 from right to left.
3Link—green
100—green
FDX—green
Indicates link activity
100BASE-T active
Green when full duplex active, off when in half-duplex mode
4ACT—green
SYS—green
PWR—green
Blinking green during packet transfer and interrupts
Blinking green for power on and self-test, solid green thereafter
Solid green when system has power
Table 1-3 Cisco 2430 Series IAD LEDs (Cisco 2432-24FXS shown)
No LED/Color Description
103054
IAD2431-8FXS
AAANNNNXXXX
AAANNNNXXXX