Cisco Firepower 2130 Maintenance and service guide

Installation, Maintenance, and Upgrade
•Install, Remove, and Replace the Network Module, on page 1
•Remove and Replace the SSD, on page 3
•Remove and Replace the Power Supply Module, on page 6
•Connect the DC Power Supply Module, on page 9
•Secure the Power Cord on the Power Supply Module, on page 14
•Remove and Replace the Fan Tray, on page 18
•Install the FIPS Opacity Shield in a Two-Post Rack, on page 20
•Install the FIPS Opacity Shield in a Four-Post Rack, on page 23
Install, Remove, and Replace the Network Module
You can remove and replace the network module in the Firepower 2130 and 2140. Although the hardware
supports removing and replacing the network module while the system is running, the software does not
currently support hot swapping. You must power down the chassis to remove and replace network modules.
See Network Modules for more information.
This procedure describes how to install a network module into an empty slot that has never contained a network
module, and how to remove an installed network module and replace it with another network module.
Safety Warnings
Take note of the following component replacement safety warnings:
Statement 1028—More Than One Power Supply
This unit might have more than one power supply connection. To reduce risk of electric shock, remove
all connections to de-energize the unit.
Warning
Installation, Maintenance, and Upgrade
1

Statement 1030—Equipment Installation
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Warning
Statement 1073—No User-Serviceable Parts
There are no serviceable parts inside. To avoid risk of electric shock, do not open.
Warning
Statement 1089—Instructed and Skilled Person Definitions
An instructed person is someone who has been instructed and trained by a skilled person and takes the
necessary precautions when working with equipment.
A skilled person or qualified personnel is someone who has training or experience in the equipment
technology and understands potential hazards when working with equipment.
Warning
Statement 1090—Installation by Skilled Person
Only a skilled person should be allowed to install, replace, or service this equipment. See statement 1089
for the definition of a skilled person.
Warning
Statement 1091—Installation by an Instructed Person
Only an instructed person or skilled person should be allowed to install, replace, or service this equipment.
See statement 1089 for the definition of an instructed or skilled person.
Warning
Step 1 To install a new network module for the first time into an empty slot, do the following:
a) Power down the chassis by moving the power switch to the OFF position.
See Rear Panel for more information about the power switch.
b) Follow Steps 4 through 7 to install the new network module.
c) Power on the chassis by moving the power switch to the ON position.
Step 2 To remove and replace an existing network module, do the following:
a) Save your configuration.
b) Power down the chassis by moving the power switch to the OFF position.
See Rear Panel for more information about the power switch.
c) Continue with Step 3.
Step 3 To remove a network module, loosen the captive screw on the lower left side of the network module and pull out the
handle that is connected to the screw. This mechanically ejects the network module from the slot.
Installation, Maintenance, and Upgrade
2
Installation, Maintenance, and Upgrade
Install, Remove, and Replace the Network Module

Figure 1: Remove the Network Module
If the slot is to remain empty, install a blank faceplate to ensure proper airflow and to keep dust out of the chassis;
otherwise, install another network module.
Step 4 To replace a network module, hold the network module in front of the network module slot on the right of the chassis
and pull the network module handle out.
Step 5 Slide the network module into the slot and push it firmly into place until the handle is flush with the front of the network
module.
Step 6 Tighten the captive screw on the lower left side of the network module.
Step 7 Power on the chassis so that the new network module is recognized.
Remove and Replace the SSD
Although the hardware supports removing and replacing SSDs while the system is running, the software does
not currently support hot swapping. You must power down the chassis to remove and replace SSDs.
The 100-GB SSD is restricted to the 2110 and 2120. The 200-GB SSD is restricted to the 2130 and 2140. Do
not mix them.
Note
We may ship larger capacity SSDs depending on component supply availability. The larger capacity SSDs
are formatted to 100-GB for the 2110 and 2120 and formatted to 200-GB for the 2130 and 2140.
Note
Installation, Maintenance, and Upgrade
3
Installation, Maintenance, and Upgrade
Remove and Replace the SSD

You can install a Malware Storage Pack (MSP) in slot 2. The MSP stores threat detection data for use in future
analysis. It supports the Advanced Malware Protection (AMP) software feature. It is used as both storage and
as the Malware application repository. RAID is not supported.
Do not switch the two SSDs. You must install the MSP in slot 2. If you remove it and install it in slot 1, all
stored capture data are lost.
Caution
Safety Warnings
Take note of the following component replacement safety warnings:
Statement 1028—More Than One Power Supply
This unit might have more than one power supply connection. To reduce risk of electric shock, remove
all connections to de-energize the unit.
Warning
Statement 1030—Equipment Installation
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Warning
Statement 1073—No User-Serviceable Parts
There are no serviceable parts inside. To avoid risk of electric shock, do not open.
Warning
Statement 1089—Instructed and Skilled Person Definitions
An instructed person is someone who has been instructed and trained by a skilled person and takes the
necessary precautions when working with equipment.
A skilled person or qualified personnel is someone who has training or experience in the equipment
technology and understands potential hazards when working with equipment.
Warning
Statement 1090—Installation by Skilled Person
Only a skilled person should be allowed to install, replace, or service this equipment. See statement 1089
for the definition of a skilled person.
Warning
Installation, Maintenance, and Upgrade
4
Installation, Maintenance, and Upgrade
Remove and Replace the SSD

Statement 1091—Installation by an Instructed Person
Only an instructed person or skilled person should be allowed to install, replace, or service this equipment.
See statement 1089 for the definition of an instructed or skilled person.
Warning
Step 1 Save your configuration.
Step 2 Power down the chassis by moving the power switch to the OFF position. See Rear Panel for more information on the
power switch.
Step 3 To remove the SSD in slot 1, face the front of the chassis, loosen the two captive screws on the SSD, and gently pull it
out of the chassis. See Front Panel for the location of the SSD slots for each model. The figure below shows the 2130
and 2140 front panel.
Figure 2: Remove the SSD
Step 4 To replace the SSD in slot 1, make sure the power switch is still in the OFF position, and then hold the SSD in front of
slot 1 and push it in gently until it is seated.
Step 5 To install the MSP SSD, make sure the power switch is still in the OFF position, and then remove the blank faceplate in
Slot 2 by loosening the captive screws on either side of the faceplate.
Step 6 Hold the MSP SSD in front of slot 2 and push it in gently until it is seated.
Do not switch the two SSDs. The MSP must be installed in slot 2. If you remove it and install it in slot 1, all
stored file capture data are lost.
Caution
Step 7 Tighten the captive screws on either side of the SSD.
Installation, Maintenance, and Upgrade
5
Installation, Maintenance, and Upgrade
Remove and Replace the SSD

Step 8 Check the SSD LED to make sure the SSD is operative. See Front Panel LEDs for a description of the SSD LEDs.
Remove and Replace the Power Supply Module
Power supply modules are hot-swappable. You can remove and replace power supply modules while the
system is running.
Safety Warnings
Take note of the following power and component removal safety warnings:
Statement 1003—DC Power Disconnection
To reduce risk of electric shock or personal injury, disconnect DC power before removing or replacing
components or performing upgrades.
Warning
Statement 1005—Circuit Breaker
This product relies on the building’s installation for short-circuit (overcurrent) protection. To reduce risk
of electric shock or fire, ensure that the protective device is rated not greater than:
AC: 20A
DC: 40A
Warning
Statement 1017—Restricted Area
This unit is intended for installation in restricted access areas. Only skilled, instructed, or qualified
personnel can access a restricted access area.
Warning
Statement 1018—Supply Circuit
To reduce risk of electric shock and fire, take care when connecting units to the supply circuit so that
wiring is not overloaded.
Warning
Statement 1022—Disconnect Device
To reduce risk of electric shock and fire, a readily accessible two-poled disconnect device must be
incorporated in the fixed wiring.
Warning
Installation, Maintenance, and Upgrade
6
Installation, Maintenance, and Upgrade
Remove and Replace the Power Supply Module

Statement 1025—Use Copper Conductors Only
To reduce risk of fire, use copper conductors only.
Warning
Statement 1028—More Than One Power Supply
This unit might have more than one power supply connection. To reduce risk of electric shock, remove
all connections to de-energize the unit.
Warning
Statement 1029—Blank Faceplates and Cover Panels
Blank faceplates and cover panels serve three important functions: they reduce the risk of electric shock
and fire, they contain electromagnetic interference (EMI) that might disrupt other equipment, and they
direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates,
front covers, and rear covers are in place.
Warning
Statement 1030—Equipment Installation
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Warning
Statement 1073—No User-Serviceable Parts
There are no serviceable parts inside. To avoid risk of electric shock, do not open.
Warning
Statement 1046—Installing or Replacing the Unit
To reduce risk of electric shock, when installing or replacing the unit, the ground connection must always
be made first and disconnected last.
Warning
Installation, Maintenance, and Upgrade
7
Installation, Maintenance, and Upgrade
Remove and Replace the Power Supply Module

Statement 1089—Instructed and Skilled Person Definitions
An instructed person is someone who has been instructed and trained by a skilled person and takes the
necessary precautions when working with equipment.
A skilled person or qualified personnel is someone who has training or experience in the equipment
technology and understands potential hazards when working with equipment.
Warning
Statement 1090—Installation by Skilled Person
Only a skilled person should be allowed to install, replace, or service this equipment. See statement 1089
for the definition of a skilled person.
Warning
Statement 1091—Installation by an Instructed Person
Only an instructed person or skilled person should be allowed to install, replace, or service this equipment.
See statement 1089 for the definition of an instructed or skilled person.
Warning
Step 1 Unplug the power supply cable before removing the power supply module. You cannot disengage the power supply
module latch without first removing the cable.
Step 2 To remove a power supply module, face the back of the chassis and grasp the handle.
Step 3 Press the latch found on the right of the power supply to disengage the power supply.
Step 4 Place your other hand under the power supply module to support it while you slide it out of the chassis.
Installation, Maintenance, and Upgrade
8
Installation, Maintenance, and Upgrade
Remove and Replace the Power Supply Module

Figure 3: Remove the Power Supply Module
Power supply module handle2Power supply module 11
Power supply module 2Power supply module latch3
If the slot is to remain empty, install a blank faceplate to ensure proper airflow and to keep dust out of the chassis;
otherwise, install another power supply module.
Step 5 To replace a power supply module, hold the power supply module with both hands and slide it into the power supply
module bay.
Step 6 Push in the power supply module gently until you hear the latch engage and it is seated.
Step 7 Plug in the power supply cable.
Step 8 Check the LED on the power supply to make sure the power supply is operative. See Power Supply Modules.
Connect the DC Power Supply Module
For the Firepower 2130 and 2140, the input connector and plug must be UL-recognized under UL 486 for
field wiring. The connection polarity is from left to right: negative (–), positive (+), and ground.
Use the handle on the power supply for installation and removal. You must support the module with one hand
because of its length.
Installation, Maintenance, and Upgrade
9
Installation, Maintenance, and Upgrade
Connect the DC Power Supply Module

Figure 4: Firepower 2100 DC Power Supply Module
FAIL and OK LEDs2Handle1
Ejector latch4DC power connector3
Safety Warnings
Take note of the following warnings:
Statement 1003—DC Power Disconnection
To reduce risk of electric shock or personal injury, disconnect DC power before removing or replacing
components or performing upgrades.
Warning
Statement 1005—Circuit Breaker
This product relies on the building’s installation for short-circuit (overcurrent) protection. To reduce risk
of electric shock or fire, ensure that the protective device is rated not greater than:
AC: 20A
DC: 40A
Warning
Installation, Maintenance, and Upgrade
10
Installation, Maintenance, and Upgrade
Connect the DC Power Supply Module