Cisco 805 Series User manual

Corporate Headquarters:
Copyright © 2001. Cisco Systems, Inc. All rights reserved.
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Cisco 805 Series Router Cabling and Setup
Quick Start Guide
This document describes the basic process of cabling and configuring the Internet access device, the
Cisco 805 router. For advanced cabling information, refer to the Cisco 805 Router Hardware Installation
Guide. For advanced configuration information, refer to the Cisco 805 Router Software Configuration
Guide. These documents are available on the Cisco Documentation CD-ROM and on the World Wide Web.
You can access the most current Cisco documentation on the World Wide Web at the following sites:
•http://www.cisco.com
•http://www-china.cisco.com
•http://www-europe.cisco.com
Parts List
The shipment of your Cisco 805 router includes the following items:
•One Cisco 805 router
•One yellow Ethernet cable
•One black power supply
•One black power supply cord
•800 and SOHO Series Product Documentation CD
•Cisco 805 Fast Step CD-ROM
Figure 1 shows the items included with the router. If any of the items is missing or damaged, contact
your customer service representative.

2
Verify the PC Setup 78-6379-03
Verify the PC Setup
Figure 1 Items Included with the Router
Verify the PC Setup
Before you begin, verify that each computer that will be connected to the router has a network interface
card (NIC) installed and that Transmission Control Protocol/Internet Protocol (TCP/IP) has been loaded
and configured. For more information on how to configure TCP/IP, refer to the PC Configuration
Instructions to Establish Cisco Router-to-PC Communications, which is available on the Cisco
Documentation CD-ROM, and refer to information available the Microsoft web site.
Quick Start
Guide
Other
Documentaion
Documentation
CD-ROM
Cisco 805
Fast Step
Yellow Ethernet cable
Product documentation
Cisco 805
Fast Step CD-ROM
Desktop power supply
Black power cord

3
Connect the Cisco 800 Series Router to a PC
78-6379-03
Connect the Cisco 800 Series Router to a PC
Connect the Cisco 800 Series Router to a PC
Follow these steps to connect the Cisco 805 router to a PC with a 10- or 10/100-Mbps network interface
card (NIC):
Figure 2 Connecting a Cisco 805 Router to a PC
Step 1 Connect the yellow Ethernet cable from the yellow Ethernet port on the back panel of the router to the
Ethernet port on the NIC on the computer.
Step 2 Verify that the HUB/NO HUB switch on the left side of the back panel has been set to the NO HUB
position (out). If the button is in, press it to set it to the out position.
HUB
LINK NO HUB
CONSOLE
ETHERNET
SERIAL
Cisco 805
10 BASE T
PC
Cisco 805 Router
SER 0 OK
LAN
AUXAUX

4
Connect the Cisco 800 Series Router to a Hub 78-6379-03
Connect the Cisco 800 Series Router to a Hub
Connect the Cisco 800 Series Router to a Hub
Follow these steps to connect the Cisco 805 router to a hub:
Figure 3 Connecting a Cisco 805 Router to a Hub
Step 1 Connect the yellow Ethernet cable from the yellow Ethernet port on the back panel of the router to the
Ethernet port on the hub.
Step 2 Verify that the HUB/NO HUB switch on the left side of the back panel has been set to the HUB position
(in). If the button is out, press it to set it to the in position.
Cisco 1528 Micro Hub 10/100
Cisco 805 Router
1
SPEED
100BaseTX
10BaseT
LED
SOLID
BLINK
234
5678
MDI MDI-X
5X 6X 7X 8X
1X 2X 3X 4X
10/100
HUB
LINK NO HUB
CONSOLE
ETHERNET
SERIAL
Cisco 805
10 BASE T

5
Connect the Cisco 805 Router to a Serial Device
78-6379-03
Connect the Cisco 805 Router to a Serial Device
Connect the Cisco 805 Router to a Serial Device
The following table describes the devices most commonly connected to the router serial port and how
the serial line is used.
If you need help deciding which serial cable to order, see Appendix A, “Selecting a Serial Cable” in the
Cisco 805 Router Hardware Installation Guide. Then order one of the serial cables described in the
following table.
Serial Device WAN Options WAN Encapsulation (Framing) Network Type
Asynchronous
modem Asynchronous dial-up line Point-to-Point Protocol (PPP) Remote office to corporate office
Small office to Internet
service provider (ISP)
Channel service
unit/data service
unit (CSU/DSU)
Synchronous
leased line
Frame Relay
X.25
Synchronous leased line:
High-Level Data Link Control
(HDLC) or PPP
Frame Relay
X.25
Remote office to
corporate office
Small office to ISP
Mode Signaling Gender Part Number
DCE EIA/TIA-232 Female CAB-SS-232FC
DTE EIA/TIA-232 Male CAB-SS-232MT
DCE EIA/TIA-449 Female CAB-SS-449FC
DTE EIA/TIA-449 Male CAB-SS-449MT
DCE EIA/TIA-530 Female CAB-SS-530FC
DTE EIA/TIA-530 Male CAB-SS-530MT
DCE EIA/TIA-530A Female CAB-SS-530AFC
DTE EIA/TIA-530A Male CAB-SS-530AMT
DCE X.21 Female CAB-SS-X21FC
DTE X.21 Male CAB-SS-X21MT
DCE V.35 Female CAB-SS-V35FC
DTE V.35 Female CAB-SS-V35FT
DCE V.35 Male CAB-SS-V35MC
DTE V.35 Male CAB-SS-V35MT

6
Connect the Cisco 805 Router to a Serial Device 78-6379-03
Connect the Cisco 805 Router to a Serial Device
Figure 4 Connecting a Serial Device to a Cisco 805 Router
Note In some countries, a modem or CSU/DSU might not be necessary or might be provided by your WAN
service provider.
Step 1 Connect the appropriate end of the serial cable to the dark blue serial port on your router.
Step 2 Connect the other end of the cable to the modem or CSU/DSU.
Modem or
CSU/DSU
HUB
LINK NO HUB
CONSOLE
ETHERNET
SERIAL
Cisco 805
10 BASE T
Cisco 805 Router

7
Connect the Power and Turn On the Router
78-6379-03
Connect the Power and Turn On the Router
Connect the Power and Turn On the Router
Follow these steps to connect power to the Cisco 805 router and turn it on:
Figure 5 Connecting the Power to an 805 Router
Step 1 Make sure the router power is off. Press the power switch to standby ( ).
Step 2 Connect the power supply cable to the 6-pin connector on the router.
Step 3 Connect the power cord to the desktop power supply.
Step 4 Connect the other end of the power cord to an electrical outlet.
Step 5 Turn ON the router. Press the power switch to on (|).
HUB
LINK NO HUB
CONSOLE
ETHERNET
SERIAL
Cisco 805
10 BASE T
Desktop power supply
6-pin connector
To electrical
outlet

8
Verifying the LEDs 78-6379-03
Verifying the LEDs
Verifying the LEDs
Verify the power, Ethernet, and serial connections by checking the LEDs. Figure 6 shows the
components that you must verify and the location of their corresponding LEDs.
Figure 6 Components and Associated LEDs
The following table describes the normal pattern for these LEDs and what to do if you get an abnormal
pattern. For more information on all LEDs, see Chapter 1, “Product Overview” of the Cisco 805 Router
Hardware Installation Guide.
LED Normal Pattern Explanation If Abnormal Pattern
OK On Power is supplied to the
router. If off, see Chapter 3, “Troubleshooting” in the Cisco 805 Router Hardware Installation Guide.
LINK On Ethernet device is
connected. If off, toggleHUB/NO HUB button (if set to HUB [in], reset to NO HUB [out] or vice versa).1If still
off, see Chapter 3, “Troubleshooting” in the Cisco
805 Router Hardware Installation Guide.
1. For information on how the setting of this button on a hub affects the setting of the router HUB/NO HUB button, see Chapter
2, “Installing the Cisco 805 Router” in the Cisco 805 Router Hardware Installation Guide.
CD
(Carrier
detect)
On Packetsaresent orreceived
from serial port.2
2. The CD LED will not light until you configure the serial interface. For more information on configuring the serial interface,
see the Cisco 805 Router Software Configuration Guide.
If off for a long time, see Chapter 3,
“Troubleshooting” in the Cisco 805 Router
Hardware Installation Guide.
CD LED
Front panel
Power connector
and switch
OK LED
Back panel
Serial
port
Ethernet
port
LINK
LED

9
About the Product CD
78-6379-03
About the Product CD
About the Product CD
The 800 and SOHO Series Product Documentation CD contains the technical publications for the 800
and SOHO series routers.
System Requirements
Documentation Exceptions
This CD does not contain certain publications that were incomplete or unavailable when this CD was
produced. These documents are in the 800 and SOHO platform hardware accessory kits and should be
consulted before installing and configuring your system. You can also access these documents on the
Documentation page on Cisco Connection Online (CCO) at www.cisco.com.
•Cisco 800 Series Routers Release Notes
•Cisco 828 and SOHO 78 Routers Release Notes
•IOS Release Notes for the Cisco 800 Series Router
•IOS Release Notes for the Cisco 828 Router
•Cisco Router Web Setup User Guide
Processor Pentium 150 MHz or faster recommended
PC OS Microsoft Windows 95
Microsoft Windows 98
Microsoft Windows 2000
Microsoft Windows NT 4.0
Memory 64-MB DRAM
Drives 4x CD-ROM drive
Monitor Color monitor capable of 800 x 600 pixel
resolution
Software Netscape 3.0 or later
Internet Explorer 3.0 or later
Adobe Acrobat Reader 3.0 or later

10
Using the CD Interface 78-6379-03
About the Product CD
Using the CD Interface
When the CD is first launched, it automatically opens a browser session and displays the CD interface
in the browser window. You can use the list of books in the left pane of your display to navigate directly
to the book you want to view. Within the interface, you can use your mouse to:
•Hover over book titles in the left column for an overview of the document before opening a
document.
•Select a book title from the document list on the left or from the document drop-down menu on the
CD title bar.
•Click the Cisco Systems corporate icon to display Cisco support and service information.
•Click About This CD (notepad icon) to get additional information about this CD.
•Click Send Us Your Feedback! (pencil & notepad icon) to provide us with your feedback.
•Click Get Acrobat Reader to install a free copy of Adobe Acrobat Reader 4.0.
Changing the Display Properties of Documents
When you first launch the CD, you will notice a list of books in the left pane of your display that you
can use to navigate directly to the book you want to view. When you select the document, Acrobat
Reader opens the book in .pdf format and provides a list of topics in the left frame of the Acrobat
window. To disable this option and view the book fully in the window, click the Show/Hide Navigation
Pane button on the Acrobat toolbar. Note that when hiding bookmarks, the thumbnails, annotations, and
articles are also hidden.
Printing Documents
To print a document:
Step 1 Click the Printer icon on the Acrobat toolbar.
The Windows Print Dialog box appears.
Step 2 Select your default printer and click OK.
Ordering Printed Copies of Documents
You can order printed copies of the documents on this CD and additional copies of this CD on the 800
and SOHO platform product ordering pages on Cisco Connection Online (CCO). Registered CCO users
can order documentation for other Cisco products and the Cisco Documentation CD-ROM (containing
all Cisco documentation) through our online Subscription Services at
http://www.cisco.com/cgi-bin/subcat/kaojump.cgi.
Nonregistered CCO users can order documentation through a local account representative by calling
Cisco’s corporate headquarters (California, USA) at 408 526-4000 or, in North America, by calling
800 553-NETS (6387).
You can access the most current Cisco documentation on the World Wide Web at http://www.cisco.com,
http://www-china.cisco.com, or http://www-europe.cisco.com.