Cisco 805 Series User manual

UNPACK THE ROUTER
CONNECT CABLES TO THE ROUTER
SET UP THE ROUTER SOFTWARE
1
2
3
Quick Start Guide
SETTING UP THE CISCO 805 ROUTER
Cisco 805 Router
Modem or
CSU/DSU
Personal
computer Power
supply
Corporate
LAN
Internet

3
Unpack the Router.
Remove the yellow Ethernet cable, product documentation, and Cisco 805 Fast Step CD-ROM
from the Open Me First bag. Remove the desktop power supply and black power cord from
the accessory kit. The following figure shows the items you assembled to perform the steps in
this guide.
The router does not ship with a serial cable. If you need help deciding which serial cable to
order, see Appendix A, “Selecting a Serial Cable” in the Cisco 805 Router Hardware
Installation Guide.
Quick Start
Guide
Other
Documentaion
Documentation
CD-ROM
Cisco 805
Fast Step
Yellow Ethernet cable
Product documentation
Cisco 805
Fast Step CD-ROM
Desktop power supply
Black power cord

4
Connect Cables to the Router.
The following figure shows the router back panel, which includes ports that are color-coded to
match the cables included with the router and the serial cable you buy from Cisco.
The HUB/NO HUB button identifies the device that you connect to the yellow Ethernet port
using the yellow Ethernet cable. For example, setting the button to HUB (in) indicates that you
are connecting a hub, while setting the button to NO HUB (out) indicates that you are
connecting a server, PC, or workstation. For information on how the setting of this button on
a hub can affect the setting of this router button, see Chapter 2, “Installing the Cisco 805
Router” in the Cisco 805 Router Hardware Installation Guide.
HUB
LINK NO HUB
CONSOLE
ETHERNET
SERIAL
Cisco 805
10 BASE T

5
Connect an Ethernet device.
Connect a Hub
This section describes how to connect a hub to the router Ethernet port.
1Connect the yellow Ethernet cable to the yellow Ethernet port on your router.
2Connect the other end of the cable to an Ethernet port on the hub.
3Set the HUB/NO HUB button to HUB (in) to indicate that you are connecting a hub.
Cisco 1528 Micro Hub 10/100
Cisco 805 Router
1
SPEED
100BaseTX
10BaseT
LED
SOLID
BLINK
234
5678
MDI MDI-X
5X 6X 7X 8X
1X 2X 3X 4X
10/100
HUB
LINK NO HUB
CONSOLE
ETHERNET
SERIAL
Cisco 805
10 BASE T

6
Connect an Ethernet device (continued).
Connect a Server, PC, or Workstation
This section describes how to connect a server, PC, or workstation with a 10- or 10/100-Mbps
network interface card (NIC) to the router Ethernet port (10BaseT).
1Connect the yellow Ethernet cable to the yellow Ethernet port on your router.
2Connect the other end of the cable to the Ethernet port on the server, PC, or workstation.
3Set the HUB/NO HUB button to NO HUB (out) to indicate that you are connecting a
server, PC, or workstation.
HUB
LINK NO HUB
CONSOLE
ETHERNET
SERIAL
Cisco 805
10 BASE T
PC
Cisco 805 Router
SER 0 OK
LAN
AUXAUX

7
Connect a serial device.
The following table describes the devices most commonly connected to the router serial port
and how the serial line is used.
Ifyou need help decidingwhich serial cable toorder, see Appendix A,“Selecting a Serial Cable”
in the Cisco 805 Router Hardware Installation Guide. Then order one of the serial cables
described in the following table.
Serial Device WAN Options WAN Encapsulation (Framing) Network Type
Asynchronous
modem Asynchronous dial-up line Point-to-Point Protocol (PPP) • Remote office to corporate office
• Small office to Internet
service provider (ISP)
Channel service
unit/data service
unit (CSU/DSU)
• Synchronous
leased line
• Frame Relay
• X.25
• Synchronous leased line:
High-Level Data Link Control
(HDLC) or PPP
• Frame Relay
• X.25
• Remote office to
corporate office
• Small office to ISP
Mode Signaling Gender Part Number
DCE EIA/TIA-232 Female CAB-SS-232FC
DTE EIA/TIA-232 Male CAB-SS-232MT
DCE EIA/TIA-449 Female CAB-SS-449FC
DTE EIA/TIA-449 Male CAB-SS-449MT
DCE EIA/TIA-530 Female CAB-SS-530FC
DTE EIA/TIA-530 Male CAB-SS-530MT
DCE EIA/TIA-530A Female CAB-SS-530AFC
DTE EIA/TIA-530A Male CAB-SS-530AMT
DCE X.21 Female CAB-SS-X21FC
DTE X.21 Male CAB-SS-X21MT
DCE V.35 Female CAB-SS-V35FC
DTE V.35 Female CAB-SS-V35FT
DCE V.35 Male CAB-SS-V35MC
DTE V.35 Male CAB-SS-V35MT

8
Connect a serial device (continued).
Note: In some countries, a modem or CSU/DSU might not be necessary or might be provided
by your WAN service provider.
1Connect the appropriate end of the serial cable to the dark blue serial port on your router.
2Connect the other end of the cable to the modem or CSU/DSU.
Modem or
CSU/DSU
HUB
LINK NO HUB
CONSOLE
ETHERNET
SERIAL
Cisco 805
10 BASE T
Cisco 805 Router

9
Connect the power supply.
This section describes how to connect the power supply to the router.
1Make sure that the power switch is set to STANDBY ( ).
2Connect the power supply cable to the 6-pin connector on the router.
3Connect the female end of the power cord to the desktop power supply.
4Connect the male end of the power cord to an electrical outlet.
5Press the power switch to ON (|).
HUB
LINK NO HUB
CONSOLE
ETHERNET
SERIAL
Cisco 805
10 BASE T
Desktop power supply
6-pin connector
To electrical
outlet

10
Verify the router connections.
Verify the power, Ethernet, and serial connections by checking the LEDs. The following figure
shows the components that you must verify and the location of their corresponding LEDs.
CD LED
Front panel
Power connector
and switch
OK LED
Back panel
Serial
port
Ethernet
port
LINK
LED