Cisco ASR1002 - ASR 1002 Router User manual

QUICK START GUIDE
Cisco ASR 1002-F Router
1Documentation and Resources
2Obtaining Documentation and Submitting a Service Request
3Cisco ASR 1002-F Router Overview
4Prepare for Installation
5Rack-Mount the Router
6Connect the Router to the Network
7Start the System
8Configure the Router
9After Installation

2
1 Documentation and Resources
Documentation for the Cisco ASR 1000 Series Aggregation Services Routers documentation is online with the exception of the
regulatory compliance and safety documentation and the Cisco ASR 1000 Series Aggregation Services Routers documentation
flyer. For detailed hardware installation instructions, refer to the online Cisco ASR 1000 Series Aggregation Services Routers
Hardware Installation Guide. Refer to the following documentation for more information on the Cisco ASR 1000 Aggregation
Services Routers:
•Shared port adapter documentation—See the Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware
Installation Guide and Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide
•Configuration documentation—See the Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Document Revision History
The Document Revision History table below records technical changes to this document.
2 Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the
monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be
delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS
version 2.0.
3 Cisco ASR 1002-F Router Overview
The Cisco ASR 1002-F (Fixed) Router is one of the Cisco ASR 1000 Series Aggregation Services Routers. It is the smallest router
that supports all the general-purpose routing and security features of the Cisco ASR 1002 Routers. It uses the same internal
control and data-plane architecture as the Cisco ASR 1002 Router. For detailed information about the Cisco ASR 1002-F
Router, see Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation Guide. Figure 1 shows the front of the
Cisco ASR 1002-F Router.
Figure 1 Cisco ASR 1002-F Router — Front View
Document Version Date Change Summary
OL-19050-01 June 2009 First version of the Cisco ASR 1002-F
Router
1Integrated Cisco ASR1002-ESP-F 3Cisco ASR 1002-SIP10-F
2Integrated RP
274680
PWR
STAT
ESP
STBY
ACTV
PWR
STAT
MIN
MAJ
CRIT
0
1
STAT
GE0 GE1 GE2 GE3 BOOT BITS LINK MGMT CC
CON AUX
CARRIER
PWR STAT
CLASS 1 LASER PRODUCT
ASR1002-F
STATUS
SPA-4XOC3-POS
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
0
1
2
3
3
1
2

3
4 Prepare for Installation
This section contains information about tools and parts, warnings, site preparation information, and information for equipment
shelf or tabletop installation and rack-mount installation.
Warning Only trained and qualified personnel should install, replace, or service this equipment. Statement 1030
Caution The eUSB panel door on the side of the Cisco ASR 1002-F Router must not be opened. There is a Do Not Tamper
label on the panel door. Do not remove the label. If there is a problem with the eUSB flash card, the chassis should
be returned.
Note Only Cisco software release code four supports the new Cisco ASR 1002-F Router. Do not use earlier versions of Cisco
software code.
Before beginning this router installation, read the Regulatory Compliance and Safety Information for the Cisco ASR 1000 Series
Aggregation Services Routers document.
Site Preparation and Unpacking
•Lift the router safely out of the packing container.
•Ensure the power service at the site is suitable for the router you are installing.
•Check the packing slip to ensure that all the proper components are present.
•Locate and have accessible the Site Log for recording information about this installation.
Tools and Parts
Use the following list of tools and parts as a checklist for preparing to install the Cisco ASR 1002-F Router:
•ESD-preventative wrist strap
•AC power cord
•Appropriate cables to connect the router to the network and to the console terminal
•Tape measure and level (optional)
•Screwdrivers: Number 2 Phillips screwdriver and 3.5-mm or 3/16-inch flat-blade screwdriver
•Chassis ground lugs and screws
•The rack-mount kit includes screws for the 19-inch rack-mount brackets (front and rear rails)
•Two cable management brackets and screws for both sides of the chassis
Prepare for Equipment Shelf or Tabletop Installation
For an equipment shelf or tabletop installation, verify the following before installing the router:
•The router is off the floor and has adequate ventilation.
•An adequate chassis ground (earth) connection exists for the router.
•The router needs at last 3 inches (7.62 cm) of clearance at the inlet and exhaust vents (front and rear of router).
•The router needs 19 inches (48.26 cm) of clearance at the front and rear to allow for installation or to access cables or
equipment.

4
Prepare for Rack-Mount Installation
Before you begin the rack-mounting tasks:
•Decide whether or not you want to front-mount or rear-mount the chassis.
•Decide whether or not you want to attach cable-management brackets to your chassis.
Note If you install cable-management brackets, make certain that you use the specified rack-mount ear holes as stated
in the procedure and install the brackets after the chassis is mounted in the equipment rack.
•Decide if two-post or four-post rack-mount equipment will be used.
5 Rack-Mount the Router
This section provides information for rack-mounting the router.
Attach the Rack-Mount Brackets—Chassis Front-Mounted
To install the rack-mount brackets on a Cisco ASR 1002-F Router for a front rack-mount configuration, follow these steps:
Step 1 Locate the threaded holes in the front sides of the chassis.
Step 2 Align the rack-mount bracket to the side of the router. Depending on which set of rack-mount bracket holes you choose
to use to attach the rack-mount bracket to the router, the chassis will either be recessed in the rack or protrude from
the rack.
Step 3 Position the front rack-mount bracket top hole with the chassis first top hole behind the side vent holes as shown in
Figure 2.
Figure 2 Attaching Front Rack-Mount Brackets for the Cisco ASR 1002-F Router
Step 4 Insert and tighten the black screws on one side.
Step 5 Repeat Step 1 through Step 4 on the other side of the chassis.
1Front rack-mount bracket ear and holes 3Front rack-mount bracket screws
2Front rack-mount bracket
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
0
274497
21
3

5
Step 6 To install the cable-management bracket, see the “Attach the Cable-Management Brackets” section on page 9.
Attach the Rack-Mount Brackets—Chassis Rear-Mounted
To install the rack-mount bracket on a Cisco ASR 1002-F Router for a rear rack-mount configuration, follow these steps:
Step 1 Align the rack-mount bracket to the side of the router and locate the threaded ear holes in the rear sides of the chassis.
Step 2 Position the rear rack-mount bracket top hole with the chassis from the back (See Figure 3). Make certain that you hold
the rear rack-mount bracket with the ear holes facing outward and towards the rear of the chassis.
Figure 3 Attaching the Cisco ASR 1002-F Router Rear Rack-Mount Brackets
Step 3 Insert and tighten the screws.
Step 4 Repeat Step 1 through Step 3 on the other side of the chassis.
This completes the procedure for attaching rear rack-mount brackets to the chassis. Continue to the section Four-Post Rack
Installation, page 5 or the section Two-Post Rack Installation, page 7.
Four-Post Rack Installation
To install the chassis in a four-post rack, read the notes before you begin and then follow the steps listed in this section.
Note Inner clearance (the width between the inner sides of the two posts or rails) must be at least 19 inches (48.26 cm).
Note We recommend that you allow at least 1 or 2 inches (2.54 or 5.08 cm) of vertical clearance between the router and any
equipment directly above and below it.
Figure 4 shows the Cisco ASR 1002-F Router in a four-post rack.
1Rear rack-mount bracket ear and holes 3Rear rack-mount bracket screws
2Rear rack-mount bracket
280279
2
3
1

6
Figure 4 Installing the Cisco ASR 1002-F Router in a Four-Post Rack - Front and Rear Rack-Mounting
Note Because the rack-mount brackets support the weight of the entire chassis, be sure to use all the screws to fasten the
rack-mount brackets on the chassis to the rack posts.
Note Make certain that you attach the cable-management bracket to the chassis after you install the chassis in an equipment
rack.
To install the chassis in the four-post rack, complete the following steps:
Step 1 Make sure that your path to the rack is unobstructed and if the rack is on wheels, ensure that the brakes are engaged
or that the rack is otherwise stabilized.
Step 2 On the chassis, ensure that all screw fasteners on all installed components are securely tightened.
Step 3 Lift the chassis into position between the rack posts (requires two people).
Step 4 Position the chassis until the rack-mount bracket ears are flush against the mounting rails on the rack. At this point, if
there is a third person, then that person can insert the screws while the other two people hold the chassis in place, unless
the chassis is resting on a shelf.
Tip Insert the bottom screw first and then the second screw at the top of the chassis diagonally from the bottom screw. This
helps secure the chassis in place while you insert the other screws.
1Rear rack equipment rail 3Front rack-mount bracket ear and holes
2Rear rack-mount bracket ear and holes 4Front rack equipment rail
274499
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
0
4
1
3
2

7
Tip To allow space to attach the cable-management brackets to the chassis in the rack easily, make certain that you use the
rack-mount bracket ear holes specified in Step 5.
Step 5 Hold the chassis in position against the mounting rails and follow these steps:
a. Insert the bottom screw into the second bracket ear hole from the bottom of the rack-mount bracket ear and use a
hand-held screwdriver to tighten the screw to the rack rail.
b. Insert the top screw into the second bracket ear hole from the top of the rack-mount bracket ear hole diagonally from
the bottom screw and tighten the screw to the rack rail. See Figure 4.
c. Repeat Step 4 and Step 5 for the other side of the chassis.
Note As a result of using the specified rack-mount bracket ear holes, the cable-management bracket can be attached
easily to the rack-mount bracket after the chassis is in the rack.
This completes the procedure for installing the chassis in a four-post rack. Proceed to the “Attach the Cable-Management
Brackets” section on page 9 to continue the installation.
Two-Post Rack Installation
To install the chassis in a two-post rack, read the notes before you begin and then follow the steps listed in this section.
Note Inner clearance (the width between the inner sides of the two posts or rails) must be at least 19 inches (48.26 cm).
Note Make certain that you attach the cable-management brackets to the chassis after you install the chassis in an equipment
rack.

8
Figure 5 shows the Cisco ASR 1002-F Router installed in a two-post rack
Figure 5 Installing the Cisco ASR 1002-F Router in a Two-Post Rack
Caution If you are using a two-post rack, secure the rack to the floor surface to prevent tipping and avoid bodily injury and
component damage.
Step 1 Position the chassis so the front is closest to you and slide the chassis into the rack, pushing it back until the rack-mount
brackets meet the mounting strips or posts on both sides of the rack. To prevent injury, avoid any sudden twists or
moves.
Step 2 Make certain that the chassis rack-mount bracket ears are flush against the mounting rails on the rack.
Note Because the rack-mount brackets support the weight of the entire chassis, be sure to use all screws to fasten the
rack-mount brackets on the chassis to the rack posts.
Tip To allow space to attach the cable-management brackets to the chassis in the rack easily, make certain that you use the
rack-mount bracket ear holes specified in Step 3.
Step 3 Hold the chassis in position and follow these steps:
a. Insert the bottom screw into the fifth hole from the top of the rack-mount bracket ear and use a hand-held screwdriver
to tighten the screw to the rack rail.
b. Insert the top screw into the second bracket ear hole from the top of the rack-mount bracket ear hole diagonally from
the bottom screw and tighten the screw to the rack rail. See Figure 5.
Step 4 Repeat Step 2 and Step 3 for the other side of the chassis.
Note As a result of using the specified rack-mount bracket ear holes, the cable-management bracket can be attached
easily to the rack-mount bracket after the chassis is in the rack.
1Rack equipment rail 2Rack-mount bracket ear and holes
274500
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
0
1
2

9
This completes the procedure for installing the chassis in a two-post rack. Proceed to the “Attach the Cable-Management
Brackets” section on page 9 to continue the installation.
Attach the Cable-Management Brackets
The cable-management brackets for the Cisco ASR 1002-F Router contain one independent cable-management “U” feature with
two screws for each bracket. For the Cisco ASR 1000 Series SIP, these brackets work in tandem with SPA cable-management
brackets to allow installation and removal of adjacent SPAs without the need to remove cables.
Note Make certain that the cable-management bracket “U” feature (open end) is facing upwards when you attach it to the
chassis.
Follow these steps to attach the cable-management brackets to both sides of the Cisco ASR 1002-F Router in the rack:
Step 1 Align the cable-management bracket to the rack-mount bracket on one side of the Cisco ASR 1002-F Router. The
cable-management bracket aligns to the top hole of the chassis rack-mount bracket.
Note Use the package of four screws that came with the cable-management bracket package.
Step 2 Insert one screw through the top screw hole of the cable-management bracket and into the chassis rack-mount bracket
and tighten the screw using a Phillips screwdriver.
Figure 6 Attaching the Cable-Management Brackets to the Cisco ASR 1002-F Router
Step 3 Insert one screw through the bottom screw hole of the cable-management bracket and into the chassis rack-mount
bracket and tighten the screw using a Phillips head screwdriver. Figure 6 shows the cable-management brackets attached
to the chassis.
Step 4 Repeat Step 1 through Step 3 for the other side of the Cisco ASR 1002-F Router.
1Cable-management bracket bottom screw hole and top
screw hole
3Chassis front rack-mount bracket
2Cable-management “U” feature
274498
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
02
3
1

10
This completes the procedure for installing the cable-management brackets on a Cisco ASR 1002-F Router for a chassis
rack-mount configuration.
Chassis Ground Connection Installation
Before you connect power or turn on power to your router, you must provide an adequate chassis ground (earth) connection
for the Cisco ASR 1002-F Router. The two-hole chassis ground lug and the respective screws that ship with your Cisco
ASR 1002-F Router.
The following tools, equipment, and supplies are necessary to connect the system ground to the chassis:
•Phillips screwdriver
•Dual-lug chassis ground component (two) and respective screws (four) (shipped with the accessory kit)
•Grounding wire
See Figure 7 for the location of the chassis ground connector on the Cisco ASR 1002-F Router.
Figure 7 Cisco ASR 1002-F Router Ground Connector Location and eUSB Panel Door
Step 1 Use the wire stripper to strip one end of the AWG #6 wire approximately 0.75 inches (19.05 mm).
Step 2 Insert the AWG #6 wire into the wire receptacle on the ground lug.
Step 3 Use a manufacturer’s recommended crimping tool to carefully crimp the wire receptacle around the wire; this step is
required to ensure a proper mechanical connection.
1Cisco ASR 1002-F Router ground connector location 1eUSB panel door
274501
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
0
1
2