Cisco 910 User manual

1
Quick Start Guide for Cisco 910 Industrial Routers
Quick Start Guide for Cisco 910 Industrial
Routers
78-21635-01C0
Overview, page 2
Accessories, page 3
Ports, page 4
LED Definition, page 5
Installation of the Device, page 9
Powering On and Logging In to the System, page 19
Resetting to Factory Mode, page 20
FCC Class A Notices and Warnings, page 20
RF Exposure Safety Notice, page 20
Declaration of Conformity with Regard to the EU Directive 1999/5/EC (R&TTE Directive), page 21
Regulatory Standards Compliance, page 23
For More Information, page 24
This guide describes how to quickly install the Cisco 910 Industrial Router.
For configuration information, see the Cisco 910 Industrial Router documentation on Cisco.com. For system
requirements, important notes, limitations, open and resolved bugs, and documentation updates, see the release notes
on Cisco.com.
Before installing, configuring, or upgrading the Cisco 910 Industrial Router, refer to the Release Notes for the latest
information.
Note: If you are using the 3G models of Cisco 910 Industrial Routers, the Mobile Equipment Identifier (MEID), International
Mobile Equipment Identity (IMEI), and Electronic Serial Number (ESN) are necessary for you to set up the 3G interface to
be used for your service provider carriers. You can use the show cellular unit all command to display MEID, IMEI, and
ESN information. For more information, see the “Monitoring Cellular 3G Information” section in Chapter 20, Configuring
Cellular 3G Setting, of the Cisco 910 Industrial Router Software Configuration Guide.

2
Quick Start Guide for Cisco 910 Industrial Routers
Overview
Overview
The Cisco 910 Industrial Router is available in following models: IR910-K9, IR910G-K9/IR910G-NA-K9, and IR910W-K9
(Figure 1). IR910-K9 supports only the Ethernet combo uplink, IR910W-K9 supports both Wi-Fi and Ethernet combo
uplink. and IR910G-K9/IR910G-NA-K9 supports both 3G (CDMA-EVDO or HSPA selective) and Ethernet combo uplink.
Figure 1 Cisco 910 Industrial Router Models
No. Model No. Description
1IR910-K9 Cisco 910 Industrial Router (Ethernet only)
2IR910G-K9
IR910G-NA-K9
Cisco 910 Industrial Router (3G and Ethernet)
3IR910W-K9 Cisco 910 Industrial Router (Wi-Fi and Ethernet)
1 2 3
390960

3
Quick Start Guide for Cisco 910 Industrial Routers
Accessories
Accessories
This section describes the basic model accessory kit contents of the Cisco 910 Industrial Router package, and
configurable items, spares, and options.
Package Contents
Figure 2 shows the accessories of the three basic models of the Cisco 910 Industrial Router:
Figure 2 Accessories of Basic Models
No. Accessory Kit Contents Contained in Model No.
1Chassis IR910-K9,
IR910G-K9/IR910G-NA-K9,
and IR910W-K9
2DIN mounting kit, preinstalled at the rear of the device
3DC power connectors jack x 2
43G antenna IR910G-K9/IR910G-NA-K9
5Wi-Fi antenna IR910W-K9
63G or Wi-Fi antenna wire clip IR910G-K9/IR910G-NA-K9 and IR910W-K9
1
2
3
4
5
6
390961

4
Quick Start Guide for Cisco 910 Industrial Routers
Ports
Configurable Items, Spares, and Options
Table 1 shows the configurable items, spares, and options of the Cisco 910 Industrial Router:
Note: All the configurable items, spares, and options should be purchased individually, and are not included by default
with the Cisco 910 Industrial Router. Verify that you have received the items you have purchased. If any item is missing
or damaged, contact your Cisco representative or reseller.
Ports
Table 2 shows the ports of the Cisco 910 Industrial Router models.
Table 1 Configurable Items, Spares, and Options
Configurable Items Model No. Description
ACC-IR910-S16 External storage, SSD media, 16-GB capacity.
ACC-IR910-H-M= IP55 enclosure and wall and pole mount kit.
ACC-IR910-W-M= Mount bracket to fix sensor module into chassis.
ACC-IR910-LORA-868 868 MHz LoRa card and antenna.
ACC-IR910-LORA-433 433 MHz LoRa card and antenna.
Table 2 Cisco 910 Industrial Router Ports
Model No. Port
IR910-K9 1 GE combo (1 RJ-45 + 1 SFP) uplink
1 Open slot for sensor module
1 USB 2.0
2 RS232/RS485 (RJ-45) serial ports
1 Console (RJ-45)
IR910W-K9 1 GE combo (1 RJ-45 + 1 SFP) uplink
1 Open slot for sensor module
1 USB 2.0
2 RS232/RS485 (RJ-45) serial ports
1 Console (RJ-45)
Wi-Fi, 2.4GHz, 802.11 b/g/n
IR910G-K9
IR910G-NA-K9
1 GE combo (1 RJ-45 + 1 SFP) uplink
1 Open slot for sensor module
1 USB 2.0
2 RS232/RS485 (RJ-45) serial ports
1 Console (RJ-45)
3G (CDMA-EVDO/HSPA selective)

5
Quick Start Guide for Cisco 910 Industrial Routers
LED Definition
LED Definition
Figure 3, Figure 4, and Figure 5 show the positions of LEDs on the panel of each model. For detailed LED definitions, see
Table 3.
Figure 3 LEDs of IR910-K9
1
2
348
10
12
11
7
9
391243

6
Quick Start Guide for Cisco 910 Industrial Routers
LED Definition
Figure 4 LEDs of IR910W-K9
1
2
348
10
12
11
7
5
9
391245

7
Quick Start Guide for Cisco 910 Industrial Routers
LED Definition
Figure 5 LEDs of IR910G-K9/IR910G-NA-K9
1
2
348
10
12
11
7
6
9
391244

8
Quick Start Guide for Cisco 910 Industrial Routers
LED Definition
Table 3 shows the color and meaning of each LED.
Table 3 LED Definition
No. LED Single/Dual
Color
Color Meaning
1SYS Dual Off System is not powered on or CPU has not
completed boot up.
Blinking green System is in the Power-on self-test (POST)
stage, or system is getting IP address
(IR910G-K9 only).
Solid green System is operating normally, and IP address is
attached (IR910G-K9 only).
Solid red System is not functioning properly.
2VPN Dual Off VPN is not set up.
Blinking green VPN setup is in progress.
Solid green VPN is operating normally.
Solid red VPN is not functioning properly.
3COM1 Dual Off COM port is enabled and is configured as
RS232 port.
Solid green COM port is enabled and is configured as
RS485 port.
Solid red Not defined.
4COM2 Dual Off COM port is enabled and is configured as
RS232 port.
Solid green COM port is enabled and is configured as
RS485 port.
Solid red Not defined.
5Wi-Fi Single Off No activity.
Solid green The connection between the gateway and base
station has been established.
Blinking green Wi-Fi is transmitting data.
63G Single Off No activity.
Solid green Module is active (SIM card inserted).
7Open slot status Single Off No link.
Solid green Port link.
Blinking green Transmitting or receiving data.
8GE-RJ-45 Single Off No link.
Solid green Port link, no activity.
Blinking green Link is normal with activity.
9GE-SFP Single Off No link.
Solid green Port link, no activity.
Blinking green Link is normal with activity.

9
Quick Start Guide for Cisco 910 Industrial Routers
Installation of the Device
Installation of the Device
You can install the device to a standard DIN rail, or on a wall or a pole by using the IP55 enclosure and wall/pole mount
kit. For detailed installation procedure, see Mounting Kit Assembly Guide for Cisco 910 Industrial Router.
Before You Begin
Before installing a Cisco 910 Industrial Router, verify that these guidelines are met:
—Sufficient front clearance is available so that the LEDs can be seen.
—Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent lighting. Make sure
that the cables are safely away from other devices that might damage them.
—Airflow around the device is unrestricted.
—Temperature around the unit does not exceed 70°C.
—Humidity around the device does not exceed 85 percent.
—Altitude at the installation site is below 2000 m.
Warning Statements
Warning: IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any
equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for
preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the
10 DC-A Dual Off Power is not present on the circuit, or the
system is not powered up.
Solid green Power is present on the associated circuit and
the router is already booted up.
Solid red Power is not present on the associated circuit
and the router is configured for dual-input
power.
11 DC-B Dual Off Power is not present on the circuit, or the
system is not powered up.
Solid green Power is present on the associated circuit and
the router is already booted up.
Solid red Power is not present on the associated circuit
and the router is configured for dual-input
power.
12 SSD Single Off No power is provided to SSD.
Solid green Power is provided to SSD.
Blinking green SSD is being accessed.
Table 3 LED Definition (continued)
No. LED Single/Dual
Color
Color Meaning

10
Quick Start Guide for Cisco 910 Industrial Routers
Installation of the Device
translated safety warnings that accompanied this device. Statement 1071
SAVE THESE INSTRUCTIONS
Warning: In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a
minimum of 7.9 inches (20 cm) or more from the body of all persons. Statement 332
Warning: This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the
protective device is rated not greater than: 20A. Statement 1005
Warning: The plug-socket combination must be accessible at all times, because it serves as the main disconnecting
device. Statement 1019
Warning: This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an
electrician if you are uncertain that suitable grounding is available. Statement 1024
Warning: Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning: Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Warning: For connections outside the building where the equipment is installed, the following ports must be
connected through an approved network termination unit with integral circuit protection:
10/100/1000 Ethernet. Statement 1044
Warning: To prevent the system from overheating, do not operate it in an area that exceeds the maximum
recommended ambient temperature of: Statement 1047
140°F (60°C) (with SSD)
140°F (60°C) (without SSD card and in a sealed enclosure)
158°F (70°C) (without SSD card and in a vented enclosure)
Warning: Installation of the equipment must comply with local and national electrical codes. Statement 1074
Warning: To prevent airflow restriction, allow clearance around the ventilation openings to be at least:
3 inches (7.6 cm). Statement 1076
Warning: Hot surface. Statement 1079
Caution: This industrial router can only be accessed by service personnel or by users who have been instructed
about the reasons for the restrictions applied to the location. Access is through the use of a tool or lock and key, or
other means of security, and is controlled by the authority responsible for the location.
Caution: Be aware of the size and weight of the Cisco 910 Industrial Router when mounting. Ensure that the
mounting location has a stable flat surface and can safely support the weight of the device.
WARNING
HOT SURFACE
DO NOT TOUCH
390965