Cisco ASR 1002 Manual

Cisco ASR 1002 Router Overview and Installation
This chapter describes the Cisco ASR 1002 Router and provides procedures for installing the Cisco ASR
1002 Router on an equipment shelf or tabletop or in an equipment rack.
This chapter contains the following sections:
•Cisco ASR 1002 Router Description, page 1
•Installation Methods, page 16
•General Rack Installation Guidelines, page 16
•Guidelines for an Equipment Shelf or Tabletop Installation, page 17
•Equipment Shelf or Tabletop Installation, page 18
•Rack-Mounting the Cisco ASR 1002 Router, page 20
•Attaching the Chassis Rack-Mount Brackets, page 22
•Installing the Cisco ASR 1002 Router in a Rack, page 25
•Attaching the Cable-Management Bracket, page 30
•Attaching a Chassis Ground Connection, page 31
•Connecting the Shared Port Adapter Cables, page 34
•Connecting the Console and Auxiliary Port Cables, page 35
•Cisco ASR 1002 Router Power Supplies, page 37
•Connecting a Terminal to the Cisco ASR1000-RP1 Console Port, page 54
•Connecting Cables, page 55
Cisco ASR 1002 Router Description
The Cisco ASR 1002 Router is part of the Cisco aggregation services family of routers. The Cisco ASR 1002
Router offers a compact form factor router that satisfies customer demands such as low power consumption
and decreased usage of rack space.
The Cisco ASR 1002 Router supports three half-height SPAs and an optional built-in 4xGE SPA. The Cisco
ASR 1002 Router supports all the general-purpose routing and security features of the Cisco ASR 1000 Series
Cisco ASR 1000 Series Router Hardware Installation Guide
1

Routers. It uses the same internal control and data-plane architecture as the other Cisco ASR 1000 Series
Routers.
The Cisco ASR 1002 Router supports:
•Cisco ASR1000-ESP5 or Cisco ASR1000-ESP10 as a field-replaceable unit (FRU)
•The Cisco Embedded Route Processor which supports 2MB upgradeable BootROM and 8 GB eUSB
bulk storage.
•1 + 1 redundant AC or DC power supplies.
•Stratum-3 network clocking per GR-1244-CORE, with T1/E1 BITS interface or SPAs as timing sources.
•A built-in 4x1GE SPA providing four small form-factor pluggable (SFP-based) GE connections,
designated as SPA bay 0.
For information about the SFP transceiver modules that are compatible with Cisco ASR 1002 Built-in Gigabit
Ethernet Ports (4x1GE), refer to the “Modular Optics Compatibility”section in Cisco ASR 1000 Series
Aggregation Services Routers SIP and SPA Hardware Installation Guide .
The Cisco ASR 1002 Router supports upgradeable Cisco ASR1000-ESP5 or ASR1000-ESP10 assembly and
the power supply modules as field-replaceable units. The Cisco integrated ASR1000-SIP10 and Cisco built-in
ASR1000-RP1 assemblies are fixed into the chassis and are not upgradeable; but the shared port adapters in
the SIP are field upgradable.
This section contains the following topics:
•Front View, on page 2
•Rear View, on page 3
•Cisco ASR 1002 Router Slot Numbering, on page 4
Front View
Cisco ASR 1002 router front view shows the Cisco ASR 1002 Router with modules installed.
Figure 1: Cisco ASR 1002 Router — Front View
SPA subslot 13Embedded ASR 1000
Series Route Processor in
the subslot and represents
the built in 4xGE SPA.
1
Cisco ASR 1000 Series Router Hardware Installation Guide
2
Cisco ASR 1002 Router Overview and Installation
Front View

SPA subslot 34SPA subslot 22
The SPAs in subslots 1-3 are field upgradeable. The SIP that the SPAs reside in is not field-upgradeable
and the Cisco ASR 1000 Series Route Processor is embedded in the chassis and not field upgradeable.
Note
Rear View
Cisco ASR 1002 router AC power supply image shows the Cisco ASR 1002 Router AC power supply.
Figure 2: Cisco ASR 1002 Router AC Power Supply
AC power supply fan5Chassis ESD socket1
AC power supply captive
installation screw
6AC power supply slot
number 0
2
AC power supply slot
number 1
7AC power supply On (|)
/Off (O) switch
3
AC power inlet8AC power supply LEDs4
Cisco ASR 1000 Series Router Hardware Installation Guide
3
Cisco ASR 1002 Router Overview and Installation
Rear View

c_Rear_View_1271213.xml shows the Cisco ASR 1002 Router DC power supply.
Figure 3: Cisco ASR 1002 Router DC Power Supply
DC power supply captive
installation screw
6Chassis ESD socket1
DC power supply slot 1
label
7DC power supply slot 0
label
2
Ground lead8DC power supply switch
Standby/On (|)
3
Positive lead9DC power supply LEDs4
Negative lead10Power supply fan5
Internal fans draw cooling air into the chassis and across internal components to maintain an acceptable
operating temperature. The fans are located at the rear of the chassis. A two-hole grounding lug is located on
the side of the chassis. Two power supplies, either two AC power supplies or two DC power supplies are
accessed from the rear of the router.
Use only AC power supplies or DC power supplies in the Cisco ASR 1002 Router. Do not mix power
supply types.
Caution
Cisco ASR 1002 Router Slot Numbering
The Cisco ASR 1002 Router contains one Cisco embedded ASR1002-RP1 which is addressed as R0 and one
Cisco ASR1000-ESP5 or ASR1000-ESP10 forwarding processor in slot F0. The Cisco ASR 1002 Router
consists of an embedded ASR1000-RP1 and embedded ASR1000-SIP10 board supporting three half-height
SPAs or 1half-height and one full-height SPA and one Cisco ASR1000-ESP5 forwarding processor.
The SPA bays are bay 1, bay 2, and bay 3. The built-in 4xGE SPA ports are located in the SPA 0 location
and will be addressed as GE 0/0/x. The Cisco ASR 1002 Router provides a built-in 4-Gigabit Ethernet interface
Cisco ASR 1000 Series Router Hardware Installation Guide
4
Cisco ASR 1002 Router Overview and Installation
Rear View

and this SPA is physically located on the Cisco embedded ASR1000-RP1 board. The Cisco ASR 1000 Series
ESP card is located in slot 1 and labeled as FP0.
c_Cisco_ASR_1002_Router_Slot_Numbering_1243123.xml shows the Cisco ASR 1002 Router slot numbering.
Figure 4: Cisco ASR 1002 Router Slot Numbering
Cisco SPA subslot 13Embedded route
processor RP0 in subslot
0
1
Cisco SPA subslot 34Cisco SPA subslot 22
Cisco ASR 1002 Router Components
The Cisco ASR 1002 Router system is derived from the architecture of the other Cisco ASR 1000 Series
routers. The three main subassemblies of any Cisco ASR 1000 Series Routers are all supported in the Cisco
ASR 1002 Router, which is the:
•C
isco embedded ASR1000-RP1 and Cisco embedded ASR1000-SIP10 (not field upgradable)
•Cisco ASR1000-ESP5 and Cisco ASR1000-ESP10 embedded services processors are field-replaceable
units (FRU)
•AC or DC power supplies which are field-replaceable units
Cisco Embedded ASR1000-RP1 for Cisco ASR 1002 Router Description
The Cisco ASR 1000 Series route processor (embedded for the Cisco ASR 1002 Router) is the central control
processor and runs the network operating system.
The Cisco embedded ASR1000-RP1 supports management interfaces such as the Ethernet network management
port and console and auxiliary serial ports. It has LED status indicators, an RJ-45 plug for a BITS timing
reference and one USB port which can be used with smart cards for secure key distribution or for image or
configuration file updates.
The Cisco embedded ASR1000-RP1 deviates from the other ASR Series Route Processor 1 for the Cisco
ASR 1006 router and the Cisco ASR 1004 Router in the following ways:
Cisco ASR 1000 Series Router Hardware Installation Guide
5
Cisco ASR 1002 Router Overview and Installation
Cisco ASR 1002 Router Components

•Bulk file storage is on a large eUSB device (to 8 GB supported) with no SATA hard-drive supported.
•Redundant Cisco Route Processor 1 is not supported.
•Network clock changes. No second BITS clock input supported.
•A built-in 4x1GE SPA is included. This shared port adapter provides four SFP-based GE connections.
For information about the SFP transceiver modules that are compatible with Cisco ASR 1002 Built-in Gigabit
Ethernet Ports (4x1GE), refer to the “Modular Optics Compatibility”section in Cisco ASR 1000 Series
Aggregation Services Routers SIP and SPA Hardware Installation Guide .
Cisco Embedded ASR1000-SIP10 and SPAs for Cisco ASR 1002 Router Description
The Cisco embedded ASR1000-SIP10 in the Cisco ASR 1002 Router is built into the Cisco ASR 1002 Router.
The Cisco embedded ASR1000-SIP10 provides the physical and electrical termination for up to three half-height
SPAs or one full-height and one half-height SPA. Double-wide SPAs are not supported. The fourth SPA slot
is connected to the built-in 4xGE SPA that resides on the Cisco embedded ASR1000-RP1.
The Cisco embedded ASR1000-SIP10 interface, like the Cisco ASR 1006 Router and Cisco ASR 1004 Router,
supports all Cisco embedded ASR1000-SIP10 functions and services. However, the Cisco embedded
ASR1000-SIP10 differs in the following areas:
•Functions as the base board for Cisco embedded ASR1000-RP1
•Only supports three removable half-height SPAs on Bay 1, 2, and 3. The fourth SPA is a built-in 4xGE
SPA on Bay 0, which is located on the Cisco embedded ASR1000-RP1.
•Is not a field-replaceable unit (FRU) and does not support online insertion and removal (OIR).
The shared port adapters (SPAs) on the Cisco embedded ASR1000-SIP10 in the Cisco ASR 1002 Router
do support online insertion and removal.
Note
The Cisco ASR 1002 Router embedded ASR1000-RP1 also provides the circuitry for the built-in 4xGE SPA.
Cisco ASR1000-ESP5 and ASR1000-ESP10 Description
The Cisco ASR 1002 Router supports the Cisco ASR1000-ESP5 or Cisco ASR1000-ESP10 embedded services
processors. The Cisco ASR 1002 Router does not support the Cisco ASR1000-ESP20.
Cisco ASR 1000 Series Router Hardware Installation Guide
6
Cisco ASR 1002 Router Overview and Installation
Cisco ASR 1002 Router Components

Cisco ASR1000-ESP10 image shows the LEDs on the Cisco ASR1000-ESP10.
Figure 5: Cisco ASR1000-ESP10 LEDs
c_Cisco_ASR1000-ESP5_and_ASR1000-ESP10_Description_1222814.xml describes the Cisco ASR1000-ESP5
and Cisco ASR1000-ESP10 LEDs.
Table 1: Cisco ASR1000-ESP5 and Cisco ASR1000-ESP10 LEDs
Behavior in the
Power-Up State
ColorLEDLED LabelNo.
All power supplies are
within operational limits.
Solid greenPowerPWR1
Off, the router is in
standby mode.
Off
The embedded services
processor is green when
active.
GreenActiveACTV2
Code has successfully
downloaded and is
operational.
GreenSTATUSSTAT3
BOOT ROM has
successfully loaded.
Yellow
Not booted.Red
Will always be off.NoneStandbySTBY4
Cisco ASR 1000 Series Router Hardware Installation Guide
7
Cisco ASR 1002 Router Overview and Installation
Cisco ASR 1002 Router Components

The Cisco ASR 1000-ESP5 can only be used in the Cisco ASR 1002 Router.Note
Power Supplies in the Cisco ASR 1002 Router
The Cisco ASR 1002 Router power supply module supports the following Cisco power supplies:
•AC power supply operates between 85VAC to 264VAC and DC operates between –40.5 to –72VDC
•–48 VDC power supply operates between
•+24 VDC power supply operates
The power supplies are installed into the rear of the chassis and are hot pluggable. The Cisco ASR 1002 Router
supports up to 588 W input power from an infrastructure standpoint (cooling capacity, midplane and power
distribution) but initial power supply development limit is up to 470 W output (AC and DC Input).
AC Power Supply for Cisco ASR 1002 Router
The AC power supply input inlet is an IEC connector with AC switch and the current rating on the connector
and switch is 10 Amps. The AC power supply is secured into the chassis with two captive screws mounted
on the faceplate.
The following table describes the AC power supply LEDs on the Cisco ASR 1002 Router.
Table 2: Cisco ASR 1002 Router AC Power Supply LEDs
DescriptionColorLEDLED Label
The AC input voltage is greater
than 85V.
GreenPower supply activityINPUT OK
If the LED is not illuminated,
then either the input voltage is
less than 70V, or the power
supply is turned off.
If the AC input voltage is
between 70V and 85V, the
INPUT OK LED can be on, off,
or flashing.
None
All fans are operational.GreenPower supply fan activity
A bi-color LED indicates fan
status.
FAN OK
A fan failure is detected.Red
Cisco ASR 1000 Series Router Hardware Installation Guide
8
Cisco ASR 1002 Router Overview and Installation
Power Supplies in the Cisco ASR 1002 Router

DescriptionColorLEDLED Label
If the INPUT OK LED is
illuminated, this LED is red if
the DC output voltages are
below the minimum limit or
above the maximum limit.
If the INPUT OK LED is not
illuminated, this LED might be
off or red.
RedPower supply activityOUTPUT FAIL
The following image shows the AC Power Supply for the Cisco ASR 1002 Router.
Figure 6: AC Power Supply for the Cisco ASR 1002 Router
AC power supply fan5Chassis ESD socket1
AC power supply captive
installation screw
6AC power supply slot
number 0
2
AC power supply slot
number 1
7AC power supply On (|)
/Off (O) switch
3
AC power supply inlet8AC power supply LEDs4
48 VDC Power Supply for Cisco ASR 1002 Router
The –48 VDC power supply input connector is a Euro-style terminal block. It is compliant with safety agencies’
guidelines and electrical requirements of the supply. The DC power supply operates within specification from
–40.5VDC to –72VDC continuously once the power supply DC input turn on threshold of –43.5 V has been
reached.
The –48 VDC power input connector Euro-style terminal block will accept three wires: one positive polarity,
one negative polarity, and one ground wire. There are provisions on the front panel to wire tie and strain relief
Cisco ASR 1000 Series Router Hardware Installation Guide
9
Cisco ASR 1002 Router Overview and Installation
Power Supplies in the Cisco ASR 1002 Router

the DC input wiring. The connection order is negative (–), positive (+), and GND. The DC power supply is
secured into the system chassis with two captive screws mounted on the faceplate.
The following image shows the –48 VDC Power Supply for the Cisco ASR 1002 Router.
Figure 7: – 48 VDC Power Supply for the Cisco ASR 1002 Router
Power supply captive
installation screw
6Chassis ESD socket1
Power supply slot 1 label7Power supply slot 0 label2
Ground lead8Power supply switch
Standby/On (|)
3
Positive lead9Power supply LEDs4
Negative lead10Fan5
The Cisco ASR 1002 Router –48 VDC power supply LEDs are described in the following table.
Cisco ASR 1000 Series Router Hardware Installation Guide
10
Cisco ASR 1002 Router Overview and Installation
Power Supplies in the Cisco ASR 1002 Router