Cisco RV132W User manual

Cisco RV132W ADSL2+ Wireless-N and
RV134W VDSL2 Wireless-AC VPN Router
Command Line Interface (CLI) Reference Guide
CLI GUIDE

© 2016 Cisco Systems, Inc. All rights reserved.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks,
go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner
does not imply a partnership relationship between Cisco and any other company. (1110R)

Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router CLI Reference Guide
Contents
Chapter 1: Introduction 5
Accessing the CLI 5
Connecting to a Console Terminal 6
CLI Command Conventions 7
Entering Commands 7
Chapter 2: Basic Commands 9
? 9
exit 9
help 10
logout 10
quit 11
reboot 11
Chapter 3: Management Commands 13
loglevel 13
loglevel get appname 13
loglevel set appname 14
nslookup 14
ping 15
restoredefault 16
save 16
ssh 17
ssh {enable | disable} 17
ssh wan {enable | disable} 17
ssh show 18
swversion 18
syslog 19
syslog dump 19
traceroute 19

Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router CLI Reference Guide
Contents
uptime 20
Chapter 4: Configuration Commands 22
dhcpserver 22
dhcpserver config vlanID start-IP-address end-IP-address leased-time de-
fault-gateway-IP-address 22
dhcpserver reserving {add | delete} vlanID description IP-address MAC-ad-
dress 23
dhcpserver show vlanX 24
lan 24
lan config --ipaddr bridge-name primary IP-address subnet-mask 24
lan config --dhcpserver bridge-name {enable | disable} 25
lan config --dhcpclient bridge-name {enable | disable} 25
lan show bridge-name 26
lanhosts 26
lanhosts show all 26
lanhosts show vlanX 27
tr69cfg 27
tr69cfg {enable | disable} 28
tr69cfg modify --interval informinterval --acsurl acsurl --acsuser acsuser --ac-
spwd acspwd --cruser connrequser --crpwd connreqpwd 28
tr69cfg show 29
tr69cfg informEnable {enable | disable} 29
tr69cfg debug {enable | disable} 30
vlan 30
vlan add --vid vlanID --desc description --intervlan-routing {enable | disable} --
port1 {untagged | tagged | excluded} --port2 {untagged | tagged | excluded} --
port3 {untagged | tagged | excluded} --port4 {untagged | tagged | excluded}
(port4 is for RV134W) 31
vlan edit bridge-name --vid vlanID --desc description --intervlan-routing {en-
able | disable} --port1 {untagged | tagged | excluded} --port2 {untagged |
tagged | excluded} --port3 {untagged | tagged | excluded} --port4 {untagged |
tagged | excluded} (port4 is for RV134W) 31
vlan delete --vid vlanID 32
vlan show 33

Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router CLI Reference Guide
Contents
vpn 33
vpn add --name connection-name --psk pre-shared key --rwan remote wan IP
--rlan remote lan IP --rmask remote lan mask --lan local lan ip --lanmask local
lan mask 34
vpn stop --name connection-name 34
vpn start --name connection-name 35
vpn restart 35
vpn restart --name connection-name 36
vpn delete --name connection-name 36
vpn show 37
wan 37
wan {add | edit} interface atm portid.vpi.vci --linktype {eoa | pppoa | ipoa} --en-
cap {llc | vcmux} --atmcat {ubr | cbr pcr | nrt vbr pcr scr mbs | rtvbr pcr scr mbs}
39
wan delete interface atm portid.vpi.vci 39
wan {add | edit} service atm portid.vpi.vci --protocol {bridge | ipoe | pppoe | ipoa
| pppoa} 40
wan {add | edit} service ptm --protocol {bridge | ipoe | pppoe} 40
wan {add | edit} service eth --protocol {dhcp | static | pppoe | l2tp | pptp} 41
wan delete service atm portid.vpi.vci --vlan vlanID 41
wan delete service ptm --vlan vlanID 42
wan delete service eth --vlan ethlanID 42
wan show 43
wan show interface 43
wlan 44
wlan --i interface {enable | disable} 45
wlan --i interface --ssid ssid 45
wlan --ssid ssid --mode mode --band band --channel channel --vlan vlanID 46
wlan --ssid ssid --smode disable 47
wlan --ssid ssid --smode wep --authtype {0|1} --encry {128 | 64} --key1 key1 -
-key2 key2 --key3 key3 --key4 key4 --txkey {1 | 2 | 3 | 4} 47
wlan --ssid ssid --smode {wpa2_personal | wpa_personal_mixed} --encry
{TKIP_AES | AES} --skey shared key --krenew renewal-seconds 48
wlan --ssid ssid --smode {wpa2_enterprise | wpa_enterprise_mixed} --encry
{TKIP_AES | AES} --rserver radius-server-IP --rport port --skey shared-key --

Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router CLI Reference Guide
Contents
krenew renew-seconds 49
Chapter 5: Where to Go From Here 50

1
Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router CLI Reference Guide 5
Introduction
The command-line interface (CLI) provides a text-based method for managing and
monitoring the Cisco RV132W ADSL2+ Wireless-N VPN and RV134W VDSL2
Wireless-AC VPN routers. This chapter describes how to use the command-line
interface and contains the following topics:
•Accessing the CLI
•CLI Command Conventions
•Entering Commands
Accessing the CLI
Connecting via SSH
The command-line interface can be accessed by using SSH or a physical console.
To enable SSH, follow these steps:
STEP 1 Log in the web UI of the device. Enter the username/password.
STEP 2 Click Firewall > Basic Settings. Check Enable SSH to allow login from the LAN
side. Check Enable Remote SSH to allow login from Internet.
STEP 3 When accessing the device by SSH, username/password is needed. The
username/password is same as the GUI password.
After successfully log in to the router, the prompt consists of the router’s hostname
+ last 3 bytes of LAN MAC, followed by a >, as shown here:
router06000a>
To access the SSH, a terminal emulator software like PuTTY or others must be
used. We use PuTTY as an example.

Introduction
Accessing the CLI
Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router CLI Reference Guide 6
1
PuTTY - Terminal Emulator Software
First, download Putty and install it on your computer. You can download PuTTY
from http://www.chiark.greenend.org.uk/~sgtatham/putty/ or another PuTTY
download source. The "putty.exe" download is good for basic SSH.
STEP 1 Download PuTTY and save the download to your C:\WINDOWS folder.
STEP 2 If you want to make a link to PuTTY on your desktop:
•Open the C:\WINDOWS folder in Windows Explorer.
•Right click on the putty.exe file and select Send To > Desktop.
STEP 3 Double-click the putty.exe program or the desktop shortcut to launch the
application.
STEP 4 Enter your connection settings:
•Host Name: example.com
•Port: 22 (Default)
•Connection Type: SSH (Default)
STEP 5 Click Open to start the SSH session.
STEP 6 Accept the connection by clicking Yes .
STEP 7 Once the SSH Connection is open, a terminal prompt will ask for your username:
•log in as: Enter your username
STEP 8 Connect with your SSH user of choice.
STEP 9 Next, enter your password. Note that you will NOT see the cursor moving, or any
characters typed (such as ******), when typing your password. This is a standard
PuTTY security feature. Hit Enter.
You are now logged in to your server with SSH.
Connecting to a Console Terminal
The computer must have a terminal emulation software installed. The software
may be configured with the following parameters: 115200 baud, 8 data bits, no
parity, 1 stop bit, and no mode control.
To connect the router to a terminal or computer, follow these steps:

Introduction
CLI Command Conventions
Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router CLI Reference Guide 7
1
STEP 1 Connect the end of the light blue console cable with the RJ-45 connector to the
light blue console port on the router.
STEP 2 Connect the end of the cable with the DB-9 connector to the terminal or PC. If your
terminal or PC has a console port that does not accommodate DB-9 connector,
provide an appropriate adapter for that port.
STEP 3 Connect the AC power cord to the power supply.
STEP 4 Connect the power interface cable to the power connector port on the back of the
router.
CLI Command Conventions
There are certain command entry standards that apply to all commands. The
following table describes the command conventions:
Entering Commands
A CLI command is a series of keywords and arguments. Keywords identify a
command, and arguments specify configuration parameters. For example, in the
command interfaces set
appname , and set are keywords, appname is an
argument that specifies the application name. To enter the commands that require
parameters, enter the required parameters after the command keyword.
[ ] In a command line, square brackets indicate an
optional entry.
{ } In a command line, curly brackets indicate a selection
of compulsory parameters separated with the |
character. One option must be selected.
Italics Italic text indicates a parameter, variable, and
arguments.
Bold Command names and keywords are shown in bold.
Screen Display Fixed-width font indicates CLI prompts, CLI commands
entered, and system messages displayed on the
console.

Introduction
Entering Commands
Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router CLI Reference Guide 8
1
If the command entered is incomplete, invalid, or has missing or invalid
parameters, then the appropriate error message is displayed. This helps with
entering the correct command.
NOTE The commands are not case-sensitive.
All the allowable commands for RV132W & RV134W router are listed in next
chapter.
<TAB> Completes the keyword.
?Anywhere in the command line to display context-
sensitive help.
Enter (or Return) Syntax-checks and then executes a command. If there
is a syntax error, the offending part of the command
line is explained.
Ctrl-A Moves cursor to the beginning of the command line.
Ctrl-E Moves cursor to the end of the command line.
Ctrl-K Erases characters from the cursor.
Up Arrow Displays the previous command in the command
history.
Down Arrow Displays the next command in the command history.
Left Arrow Moves cursor to the previous character.
Right Arrow Moves the cursor to the next character.
Backspace Deletes the previous character.
?-Enter or ‘help’ List support commands.