Cisco Nexus 5010 User manual

QUICK START GUIDE
Cisco Video Surveillance 5010/5011 Indoor Fixed HD IP Dome Camera
Quick Start Guide
1Product Overview
2Installation
3Operation
4Next Steps
5Obtaining Documentation and Submitting a Service Request

2
78-19556-02
1 Product Overview
Figure 1 Camera Connections and Features (Side)
Figure 2 Camera Connections and Features (Top)
1Relay and Alarm Connections: Supports one relay that can be used to control an external
circuit and one alarm for physical input into the system.
2Accessory Port: For use with compatible accessories.
3RJ-45 Network Port: Connects the camera to the network. Also supplies power to the camera
through the network using Power over Ethernet (PoE). If PoE is not available, the camera is
powered for 24 VAC.
424 VAC Power Connections: Supports 24 VAC as the power source if PoE is not used.
1 2 3 4
278770
1
2 7
3 8 9
4 5 6
278771

3
2 Installation
Back Box and Lens
For detailed instructions, refer to the user guide.
Warning Remove the foam insert from the back box before installing the system. The foam insert secures the tilt ring to
prevent damage to the optical chassis during shipment.
Note Megapixel lenses are designed and tested to deliver optimal image quality to the megapixel camera. A standard
definition lens installed on a megapixel camera will limit the resolution of the camera and create poor image quality.
Step 1 Prepare the mounting surface using one of the following options:
•In-Ceiling Installation
– Cut a 6-inch diameter hole in the ceiling.
– Pull all wiring through the hole and terminate all wires (if not already terminated).
•Surface Installation
– Using the surface mount ring as a template, drill holes for the mounting hardware.
– Drill a hole in the ceiling for wiring; pull all wiring through the hole and terminate all wires (if not already
terminated).
– Attach the surface mount ring to the mounting surface.
1Reset Button: Reboots the camera or restores the camera's factory default settings. This button
is recessed. Use a small tool or a paper clip to press and release the reset button once to reboot
the camera. Press and hold the reset button for 10 seconds to restore the camera to the factory
default settings.
2Micro SD Card Slot: Saves a snapshot image to a micro SD card based on alarm activity.
3Power LED: Glows solid amber and then glows solid green during and after the configuration
sequence. The LED can be disabled through the user interface. If this LED glows red (solid or
flashing), contact technical support for assistance.
4Lens Mount: Fits a standard CS-mount lens. Use a megapixel lens with the ID Series and
IDE Series megapixel cameras. A standard definition lens installed on a megapixel camera will
limit the resolution of the camera and create poor image quality.
5Auto Iris Lens Connector: Controls the auto iris lens. Insert the 4-pin connector from the DC
drive auto iris lens into this connector.
6NTSC/PAL Button: Toggles the service port between NTSC and PAL formats. The default
setting is NTSC.
7Service Port: Outputs analog video. Use this port at the installation site to set up the field of
view and to focus the camera. When a service cable is connected to the camera, video to the
IP stream is disabled.
8Auto Back Focus Button: Sets the auto back focus mechanism. Press the button once to center
the auto back focus mechanism and to fully open the iris. Press and hold the button for three
seconds to start the auto back focus mechanism and focus the camera.
9Ethernet Activity/Link LED: Flashes green to indicate that data is being transmitted/received
by the camera. Glows solid amber to indicate that a live connection is established.

4
Step 2 Install the lens:
a. Remove the cover from the lens mount.
b. Screw the lens onto the lens mount. Be careful to prevent dust from entering the space between the lens and the imager.
If necessary, use clean, compressed air to remove any foreign matter (refer to the instructions shipped with the lens).
c. Connect the auto iris lens to the 4-pin connector located on the side of the camera. Refer to Figure 3 on page 4 for pin
designation and iris drive connector information.
Figure 3 Lens Pin Connections
Step 3 Connect the network cable to the RJ-45 network port on the side of the back box. If the network has no Power over
Ethernet (PoE), connect a 24 VAC Class 2 power supply to the 24 VAC power connector.
Figure 4 RJ-45 Pin Descriptions
Pin DC (AID) Auto Iris Lens
1Control coil negative (–)
2Control coil positive (+)
3Drive coil positive (+)
4Drive coil negative (–)
Pin Function
1TX+
2TX–
3RX+
4PoE 1-2
5PoE 1-2
6RX–
7PoE 3-4
8PoE 3-4
3
12
4
278768
12345678
8765 4 32 1
12345678 12345678
8 7 6 54 3 2 1
8
8
1
1
278769

5
Step 4 Connect the necessary wiring for alarms and relays (refer to Figure 5). Only use the 24 VAC wires if PoE is not available.
Figure 5 Alarm and Relay Wiring
Figure 6 24 VAC Wiring
Step 5 Install the back box using one of the following options:
•In-Ceiling Installation
– Install the back box by compressing the spring clips and pushing the back box through the hole (refer to
Figure 7).
– Tighten the machine screws completely to secure the back box to the ceiling.
Figure 7 In-Ceiling Installation
•Surface Installation
– Install the back box in the surface mount ring by compressing the spring clips and pushing the back box
through the hole (refer to Figure 8).
RELAY
R1
ALARM
A1
278779
24V~
278780
278781

6
– Tighten the machine screws completely to secure the back box to the ceiling.
Figure 8 Surface Installation
Step 6 Apply power to the camera. The camera will complete a configuration sequence: the green LED flashes five times per
second for approximately two minutes and then turns solid after the sequence is complete.
Note If the camera is not connected to a Dynamic Host Configuration Protocol (DHCP) server and DHCP is enabled,
the configuration sequence might take up to five minutes to complete.
Step 7 Position the camera
a. View the camera image using the service port or a Web browser.
b. Unlock the tab locks located on each side of the camera.
c. Manually rotate and tilt the camera module to position the camera. Do not over-rotate the module.
d. Lock the tab locks to secure the camera.
Figure 9 Positioning the Camera
1Tilt 180°
2Pan 355°
3Rotate 220°
4Tab lock
278772
1
2
3
4
278773

7
Step 8 Focus the lens:
a. View the camera image using the service port or a Web browser.
b. Press the auto back focus button once to center the focus mechanism. The button is located on the rim of the back box.
c. Manually adjust the zoom and focus of the lens to the desired field of view (refer to the instructions shipped with the
lens).
d. Press and hold the back focus button for three seconds to start the auto back focus mechanism.
Dome Liner and Lower Dome
Step 1 Align the magnets on the dome liner with the magnets located on the back box.
Figure 10 Installing the Dome Liner
Step 2 Attach the leash of the lower dome to the back box.
Figure 11 Attach the Leash
Step 3 Move the lower dome latches away from the bubble until you hear a click. Align the lower dome latches with the slots
located on the back box.
278774
278775

8
Figure 12 Aligning the Lower Dome with the Back Box
Step 4 Snap the lower dome into place, and then move the lower dome latches toward the bubble until you hear a click.
Figure 13 Locking the Lower Dome
Step 5 Turn the top cover of the lower dome 90-degrees to conceal the dome latches, LED, and service port.
Figure 14 Positioning the Top Cover of the Lower Dome
3 Operation
Once the camera is installed, apply power to the camera. The camera will start a configuration sequence: the green LED flashes
five times per second for approximately two minutes, and then turns solid after the boot cycle is complete and the camera is on
line.
278776
278777
278778

9
IP Address Settings
If the camera is connected to a Dynamic Host Configuration Protocol (DHCP) network and DHCP is set to the On position,
the server will automatically assign an IP address to the device; DHCP On is the default setting for the camera. Set DHCP to
the Off position to set the camera’s IP address manually.
NOTES:
•If the camera is not connected to a DHCP server but DHCP is set to On, the default IP address 192.168.0.20 on subnet
mask 255.255.255.0 is automatically assigned to the camera. After the first camera is connected and assigned the default
IP address, the system will automatically look for other cameras on the auto IP address system and assign IP addresses in
sequential order as required.
For example, if three cameras are connected to a network without a DHCP server, the first camera is assigned address
192.168.0.20, the second camera is assigned address 192.168.0.21, and the third camera is assigned address 192.168.0.22.
•Contact your network administrator to avoid network conflicts before setting/changing the camera’s IP address.
Minimum System Requirements
Processor: Intel Core™2 Duo microprocessor, 2.6 GHz
Operating System: Windows XP
Memory: 2 GB RAM
Network Interface Card: 100 megabits (or greater)
Monitor: Minimum of 1024 x 768 resolution, 16- or 32-bit pixel color resolution
Web Browser: Internet Explorer 8.0
Media Player: QuickTime 7.6.5 for Windows XP
Note This product is not compatible with QuickTime version 7.6.4 for Windows XP. If you have this version installed on
your PC, you will need to upgrade to QuickTime version 7.6.5.
Logging On to the Camera
Step 1 Open the Web browser.
Step 2 Type the camera’s IP address in the browser address bar.
Step 3 Click the Login button in the navigation bar; a dialog box appears.
Step 4 Type your user ID and password; admin is the default for both.
Note If this is the first time you are logging on to the camera as the administrator, the default User ID and Password
are admin (all lowercase). For security purposes, be sure to change the password after you log on for the first
time.
Step 5 Click Log In.

10
Live Page Icons
Viewable icons are based on group permissions. The camera has two predefined groups: Public and Admin.
Public: This defined group can be modified or deleted. The default permissions for this group are single stream view, stream
selection, and API access.
Admin: This is the only defined group that cannot be deleted; however, the administrator password can be changed. For security
purposes, it is important that you change your password after you log on to the device for the first time. This group has access
to all permissions.
Settings Page
Depending on user permissions, the Settings page allows you to manage camera system settings, set up users and groups, and
control the camera.
To access the camera settings:
Step 1 Log on to the camera.
Step 2 Click the Settings link in the navigation bar located in the upper-right corner of the page; a list of menu tabs appear.
Step 3 Place the mouse pointer over a tab to display a list of submenus.
Show Device List: Displays a list of viewable cameras connected to the same virtual local
area network (VLAN) as the camera to which you are logged on.
Note Used only in 2x2 mode to list other devices.
Disable Viewer: Closes the live view window.
Note Used only in 2x2 mode to list other devices.
1 x 1 Mode: Displays a single video pane.
2 x 2 Mode: Displays 4 video panes in rows of two.
3 x 3 Mode (full-screen mode only): Displays 9 video panes in rows of three.
4 x 4 Mode (full-screen mode only): Displays 16 video panes in rows of four.
Select Stream: Selects the viewable video stream (primary or secondary).
Maximize Viewing Area: Scales the image to the full size of the browser.
Show Toolbar: Returns the window to normal view. This icon is only available after the
window has been set to maximize viewing area.
Open Stream in New Window: Opens the video in a scalable, independent window.
Opening the video in a separate window allows you to view the video while other
applications are running. This window can be minimized, maximized, or closed using the
title bar buttons of the active window. The window can also be resized to your
specifications by dragging the lower-right corner of the window.
Take a Snapshot: Captures the image displayed in the video pane and saves it as a JPEG
file.