Cisco Small Business VC220 User manual

Quick Start Guide
Cisco Small Business
VC 220 Dome WDR Day/Night PoE Network
Camera
Package Contents
•Cisco VC 220 Network Camera
•Power Adapter
•Two L-Shaped Audio Cables
•Mounting and Installation Accessories including a TORX™
screwdriver
•I/O Connector
•Setup and Documentation CD — includes localized Quick Start
Guides in French, German, Italian, and Spanish
•Quick Start Guide

2 VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide
Welcome
Thank you for choosing the Cisco VC 220 Dome Wide Dynamic Range
(WDR) Day/Night PoE Network Camera. The Cisco VC 220 network
camera is a high-performance web-ready camera, and can be part of a
flexible surveillance system.
This guide describes how to physically install your Cisco VC 220 network
camera and how to install and launch the provided Setup Wizard.

VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide 3
Before You Begin
Before you begin the installation, make sure that you have the following
equipment and services:
•At least one computer running Microsoft Internet Explorer 6.x, or later
(other browsers can be used but may have limited functionality)
•An active LAN IP connection
After the basic hardware installation, Cisco strongly recommends that you
run the Setup Wizard on the CD-ROM for first-time software installation of
the camera. Advanced users can set up the Cisco VC 220 directly from the
web interface of the camera.
It is suggested that you install the software – see “Getting Started with
the Configuration” section on page 11 – before you replace the dome
cover on the camera. This is because after the software is installed, you
will be able to use the web-based configuration utility to see how the lens
should be adjusted and how the camera needs to be focused.
See “Suggested Next Steps” section on page 12 for instructions on lens
and focusing adjustments, and how to replace the dome cover. The
recommended order of steps is as follows:
•“Mounting Your Cisco VC 220 Camera” section on page 8
•“Connecting the Equipment” section on page 9
•“Verifying the Hardware Installation” section on page 11
•“Getting Started with the Configuration” section on page 11
•“Adjusting the Lens” section on page 12
•“Attaching the Dome Cover” section on page 13
The supplied screwdriver is exclusively designed to match the dome
screws, which prevents the cover from being removed by an unauthorized
individual. Do not discard the screwdriver because you may need to
remove the dome cover at a later time.
1

4 VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide
Product Overview
Descriptive Diagrams
The following illustrations show the major components of the camera.
Lens and Tilt
Screws
Allows you to make pan/tilt 3-axis adjustments. For wall
or ceiling mounting on an unlevel plane, you can rotate
the 3rd axis to straighten the view. See “Adjusting the
Lens” section on page 12.
Built-in Microphone Features a built-in microphone mounted on the front of
the camera. The camera also has a connection for an
external microphone on the rear. Connecting an external
microphone disables the built-in microphone.
Passive Infrared
(PIR) Sensor
Alerts you to movement up to 5 M (16.4 feet) based on
thermal detection.
2
Mounting Holes
Dome Cover
Tamper-resistant screw
MAC: 002129727D24
Lens
Tilt Screw
Built-in Microphone
PIR Sensor
IR LEDs
Power Cord Port
Ethernet RJ45 Port
Recessed Reset Button
Status LED
Light Sensor

VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide 5
Light Sensor Detects the amount of ambient light and switches the
camera from day to night. If light is too low, the light
sensor triggers the IR LEDs to turn on.
12 Infrared (IR)
LEDs
Enables operation in complete darkness. The ring of IR
LEDs are built-in with a working range of 15 m (50 feet).
Status LED Indicates the following status:
LED Off—The power is off or the LED status is turned off.
Flashing green in one second intervals—The camera
and network is functioning.
Steady orange—The camera can’t detect a networking
signal; thus the camera is not functioning. For example,
the Ethernet cable is not attached.
Flashing orange—The PIR sensor noted movement.
Flashing green rapidly—The firmware is being
upgraded.
Flashing orange rapidly—The camera’s default settings
are being restored.
Alternating flashing green and orange—Video has
been lost.
Recessed Reset
Button
Use a bent paperclip to press the Reset button. The
Reset button has two functions:
Restart—Press and hold the Reset button for less than
five seconds to reset the camera.
Restore Factory Defaults—Press and hold the Reset
button for 10 seconds to restore factory defaults.
Ethernet RJ45 Port Connects your Cisco VC 220 camera to a Power over
Ethernet (PoE) switch or router, or to a PoE power injector
(not provided) for connection to a non-PoE switch or
router. The LEDs surrounding the Ethernet port indicate
the following status:
Green—Indicates network and data activity. Light should
be steady when camera is on and flashing when data is
transmitted or received.
Amber—Indicates PoE. Should be steady when using
PoE.
Power Included. Connects your Cisco VC 220 camera to 12 V
power (1 Amp) when not using PoE.

6 VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide
Focus and Zoom
Controllers
Adjusts the focus and zoom of your camera. See
“Adjusting the Lens” on page 12.
Image and Pan
Adjustment Screws
Allows you to make pan/tilt 3-axis adjustments. For wall
or ceiling mounting on an unlevel plane, you can rotate
the 3rd axis to straighten the view. See “Adjusting the
Lens” on page 12.
GPIO (General
Purpose I/O Terminal
Block)
Allows you to connect the camera to external input/
output devices that can provide additional controlling
functions. For more information, see the Cisco VC 220
Network Camera Administration Guide found at:
http://www.cisco.com/en/US/products/ps9944/
prod_maintenance_guides_list.html.
Audio Out Connects your Cisco VC 220 camera through the
3.5 mm input jack to an external speaker or computer.
Microphone In Connects your Cisco VC 220 camera through the
3.5 mm input jack to an external microphone. When no
microphone is connected, the camera automatically
uses its internal microphone.
Audio Enables audio on or off. When off, the microphone and
speaker are muted.
General I/O Terminal Block
Audio Out
Microphone In
Pan Screw
Image Adjustment
Screw Focus Controller
Zoom Controller
Tilt Adjustment
Audio On/Off

VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide 7
Installing Your Cisco VC 220 Camera
Installation Tips
Before installing the camera, look for a spot that best suits your needs. The
built-in PIR sensor is designed to be triggered when a person enters its
detection range. Therefore, it is crucial to install your camera with the PIR
sensor facing the desired direction. The sensitivity of the PIR sensor
depends on the object size and temperature differences between the
object and the background environment.
CAUTION Do not install the Cisco VC 220 camera around sources of
heat, such as direct sunlight, radiators, ovens, or televisions.
For more location recommendations, see the Cisco VC 220
Network Camera Administration Guide found at:
http://www.cisco.com/en/US/products/ps9944/
prod_maintenance_guides_list.html.
3
I/O
Audio Out Mic. In Ext. Int.
1 2 3 4
Side viewTop view

8 VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide
Mounting Your Cisco VC 220 Camera
If you have more than one camera, make a note of the MAC address found
on the side of your camera. You may want to refer to the MAC address later
to identify multiple cameras. Your MAC address will be something like the
following: 00:21:29:72:7D:2C.
STEP 1Use the screwdriver to detach the dome cover from the camera
base.
STEP 2For a ceiling mount, insert the supplied two screws in the
corresponding holes on each side of the camera base and secure
them with a screwdriver. Consider using Steps 4 and 5 to make the
mount more secure.
For a wall mount, attach the alignment template to the wall.
STEP 3Drill two pilot holes into the ceiling/wall through the two circles on
the template.
STEP 4Hammer the supplied plastic anchors into the holes.
STEP 5Align the two holes on each side of the camera base with the two
plastic anchors on the wall, insert the supplied screws to
corresponding holes, and secure them with a screwdriver.
Your Cisco VC 220 camera is now ready for network setup.
NOTE The wall mount screws come with anchors that can be used for
drywall or concrete. The screw size is a metric M4 with a length of 31.75
mm. The anchor is the same length and internal diameter to accept the
screw.
For non-metric countries, the equivalent screw size is #8 x 1 ¼ inch. The
anchor size is #8-#10 with a length of 1 ¼ inch.
Alignment template

VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide 9
Connecting the Equipment
There are two options for deploying the Cisco VC 220 camera on the
network, a basic Ethernet setup and a Power over Ethernet (PoE) setup.
The basic setup is described in this document. For PoE setups, see the
Cisco VC 220 Network Camera Administration Guide found at:
http://www.cisco.com/en/US/products/ps9944/
prod_maintenance_guides_list.html.
4

10 VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide
Basic Ethernet Setup
Follow these steps to perform a basic Ethernet setup.
STEP 1Connect any external devices to the general I/O terminal block, if
you have sensors and alarms (1).
STEP 2Connect your Cisco VC 220 camera to a router or a switch using an
Ethernet cable (2).
STEP 3Connect the supplied power adapter (3) from the Cisco VC 220
camera to a power outlet.
2
3
Router or Switch
1: Power
2: Digital output
3: Digital input
4: Ground
1