Cisco 1548M User manual

TAKE OUT WHAT YOU NEED
CONNECT THE SWITCH TO OTHER NETWORK DEVICES
ASSIGN IP INFORMATION TO THE SWITCH
DISPLAY THE WEB-BASED SWITCH MANAGER
1
2
3
4
Quick Start Guide
CISCO 1548M MICRO SWITCH 10/100
CABLING AND START UP

1

1
Take Out What You Need
When you unpack the box that contains your Cisco 1548M Micro Switch, you should find the
items shown below.
If any item is missing or damaged, contact your Cisco representative or reseller for support.
Note: You need to supply Category 3, 4, or 5 straight-through or crossover cables to connect
to Ethernet devices.
Cisco Micro Switch
Stacking clip Rubber plug
Product documentation
Cisco ConfigMaker Software
Rollover console cable
(RJ-45-to-RJ-45)
Console-to-PC adapter
(RJ-45-to-DB-9)
Plastic fastener
Standard slot
metal screw
PWR1234
10MBPS
COL/ACT
100MBPS
COL/ACT
58
7
6
Power cord
Installation
Configuration
Guide
Quick Start
Guide
Cisco
ConfigMaker
Software

2
Connect the Switch to Other Network
Devices
RA
TING
100-127/200-240 V~
0.3A/ 0.2 50/60Hz
5x
CONSOLE
100BT
-ON/ 10BT
-OFF
FDUP-ON/ HDUP-OFF
1
6x 7x 8x
1x
Cisco 1548M
2x 3x10/100 4x
2345678
12345678
Maximum cable length:
328 ft (100 m)
10/100 network
port (RJ-45)
10BaseT or
100BaseTX port
(RJ-45)
Ethernet cable
(not supplied)
Note: Use a straight-through cable to
connect two ports when one of the ports is
designated with an X. Use a crossover cable
to connect two ports when both ports are
designated with an X.
Connect the Switch to
Servers, Routers, and
Workstations
• Connect a Category 3, 4, or 5
straight-through cable to any 10/100
port on the switch and to a 10BaseT
port on the workstation, server, or
router.
• Connect a Category 5 straight-through
cable to any 10/100 port on the switch
and to a 100BaseTX port on the
workstation, server, or router.
Connect the Switch to Hubs
and Other Switches
• Connect a Category 3, 4, or 5 crossover
cable to any 10/100 port on the switch
and to a 10BaseT port on the target hub
or switch.
• Connect a Category 5 crossover cable to
any 10/100 port on the switch and to a
100BaseTX port on the target hub or
switch.

3
Connect the Switch to Other Network
Devices (continued)
RJ-45-to-RJ-45
rollover console cable
RJ-45-to-DB-9
adapter (supplied)
RA
TING
100-127/200-240 V~
0.3A/ 0.2 50/60Hz
5x
CONSOLE
100BT
-ON/10BT
-OFF
FDUP-ON/ HDUP-OFF
1
6x 7x 8x
1x
Cisco 1548M
2x 3x10/100 4x
2345678
12345678
Console port
(RJ-45)
Power outlet
Connect the Console Cable
1Make sure console port settings of the
switch match the settings of the
terminal, PC, or laptop. The default
settings of the switch console port are
9600 baud, 8 data bits, 1 stop bit,
no parity, and no flow control.
2Connect the rollover console cable to
the CONSOLE port on the switch.
3Connect the other end of the rollover
cable to your terminal, PC, or laptop
(if necessary, use an appropriate
adapter, such as the supplied
RJ-45-to-DB-9 adapter).
4From your terminal, PC, or laptop, start
the terminal emulation program.
Power Up the Switch
1Connect one end of the power cord to
the switch and the other end to a power
source.
2Wait approximately 2 minutes for the
switch to complete its power-on self-test
(POST) and to discover the network.
After POST completes, the Continue
with configuration dialog? prompt
appears on the management station.
You can then follow the prompts to
assign IP information to the switch.

4
Assign IP Information to the Switch
The switch is designed to operate with little
or no user intervention. In most cases, you
can use it with its default settings.
Assign IP information to the switch so that
you can use the Cisco 1548 Switch Manager
web-based interface and the switch can
communicate with local routers and the
Internet.
Contact your system administrator for the
switch IP information, and record it here.
Switch IP address:
Subnet mask:
Default gateway:
1From the terminal or PC, enter Y:
Continue with configuration dialog? Y
2Enter the IP address (for example:
10.1.105.20):
Enter IP address: 10.1.105.20
3Enter the subnet mask (IP netmask)
(for example: 255.255.255.0):
Enter IP netmask: 255.255.255.0
4Enter the IP address of the default
gateway (for example: 10.1.105.254):
Enter IP default gateway: 10.1.105.254
The following information is displayed:
The following configuration command
script was created:
ip address 10.1.105.20 255.255.255.0
ip default-gateway 10.1.105.254
!
end
5Enter Y:
Use this configuration? Y
The following information is displayed:
Building configuration...
Use the enabled mode ‘configuration’
command to modify this configuration.
Press RETURN to get started.
6Press Return.
7Exit from the terminal session.
You can now display the Cisco 1548 Switch
Manager.

5
Display the Cisco 1548 Switch Manager
If you have the IP address to the switch, you can display the Cisco 1548 Switch Manager from
your intranet. You can use the Cisco 1548 Switch Manager to configure and monitor the
switch.
1Start Netscape Communicator (4.03 or higher) or Microsoft Internet Explorer
(4.01 or higher). Make sure that Java and JavaScript are enabled.
2Enter the IP address of the switch in the URL field if you are using Communicator
(the Address field if you are using Internet Explorer).
The Cisco 1548 Switch Manager Home page appears.
Note: The Cisco 1548M Micro Switch 10/100 Installation and Configuration Guide and the
Cisco 1548 Switch Manager online help provide complete information about the web console
and describe how to configure the switch.
Click Help for
procedures and
detailed field
descriptions.
Click these topics to move from page
to page. On Netscape Communicator
only, when the cursor is above a topic,
a pop-up briefly describes the options
on that particular page.
Click Revert
to discard
unapplied
changes on
a page.
Click Apply after
making changes
on a page.
Click a port to display its
settings, status, and statistics.
HOME PORT ADDRESS IP SNMP SPAN VLAN STP STATISTICSCDP SYSTEM

Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]
European Headquarters
Cisco Systems Europe s.a.r.l.
Parc Evolic, Batiment L1/L2
16 Avenue du Quebec
Villebon, BP 706
91961 Courtaboeuf Cedex
France
http://www-europe.cisco.com
Tel: [phone]
Fax: [phone]
Americas
Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
Fax: [phone]
Asia Headquarters
Nihon Cisco Systems K.K.
Fuji Building, 9th Floor
3-2-3 Marunouchi
Chiyoda-ku, Tokyo 100
Japan
http://www.cisco.com
Tel: [phone]
Fax: [phone]
Cisco Systems has more than 200 offices in the following countries. Addresses, phone numbers, and fax numbers are listed on the
Cisco Connection Online Web site at http://www.cisco.com.
Argentina •Australia •Austria •Belgium •Brazil •Canada •Chile •China (PRC) •Colombia •Costa Rica •Czech Republic •Denmark
England •France •Germany •Greece •Hungary •India •Indonesia •Ireland •Israel •Italy •Japan •Korea •Luxembourg •Malaysia
Mexico •The Netherlands •New Zealand •Norway •Peru •Philippines •Poland •Portugal •Russia •Saudi Arabia •Scotland •Singapore
South Africa •Spain •Sweden •Switzerland •Taiwan, ROC •Thailand •Turkey •United Arab Emirates •United States •Venezuela
AccessPath, Any to Any, AtmDirector, the CCIE logo, CD-PAC, Centri, the Cisco Capital logo, CiscoLink, the Cisco Management Connection logo, the Cisco NetWorks logo, the
Cisco Powered Network logo, the Cisco Press logo, the Cisco Technologies logo, ClickStart, ControlStream, DAGAZ, Fast Step, FireRunner, IGX, IOS, JumpStart, Kernel Proxy,
LoopRunner, MGX, Natural Network Viewer, NetRanger, NetRanger Director, NetRanger Sensor, NetSonar, Packet, PIX, Point and Click Internetworking, Policy Builder, Precept,
RouteStream, Secure Script, SMARTnet, SpeedRunner, Stratm, StreamView, The Cell, TrafficDirector, TransPath, ViewRunner, VirtualStream, VlanDirector, Workgroup Director, and
Workgroup Stack are trademarks; Changing the Way We Work, Live, Play, and Learn, Empowering the Internet Generation, The Internet Economy, and The New Internet Economy
are service marks; and BPX, Catalyst, Cisco, Cisco IOS, the Cisco IOS logo, Cisco Systems, the Cisco Systems logo, Enterprise/Solver, EtherChannel, FastHub, ForeSight,
FragmentFree, IP/TV, IPX, LightStream, LightSwitch, MICA, Phase/IP, StrataSphere, StrataView Plus, and SwitchProbe are registered trademarks of Cisco Systems, Inc. in the U.S. and
certain other countries. All other trademarks mentioned in this document are the property of their respective owners. (9811R)
78-5567-01