Cisco CATALYST 6500 WS-X6066-SLB-S-K9 Installation and operation manual

Corporate Headquarters:
Copyright © 2005 Cisco Systems, Inc. All rights reserved.
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Catalyst 6500 Series Switch Content Switching
Module with SSL Installation Note
Product Number: WS-X6066-SLB-S-K9
This publication describes how to install the Content Switching Module with SSL (CSM-S) in the
Catalyst 6500 series switches and includes the software and hardware requirements.
Note The term SSL daughter card refers to a Secure Socket Layer (SSL) termination daughter card that
accelerates SSL transactions. Except where specifically differentiated, the term Content Switching
Module and its acronym CSM include both the Content Switching Module and the Content Switching
Module with SSL. The term Content Switching Module with SSL and its acronym CSM-S are used only
where the information presented is specific to the CSM-S.
Contents
This publication contains these sections:
•Safety Overview, page 2
•Front Panel Description, page 7
•Environmental and System Requirements, page 9
•Installing the CSM-S, page 11
•Verifying the Installation, page 20
•Using the CLI, page 20
•Related Documentation, page 21
•Translated Safety Warnings, page 21
•Obtaining Documentation, page 24
•Documentation Feedback, page 25
•Cisco Product Security Overview, page 25

2
Catalyst 6500 Series Switch Content Switching Module with SSL Installation Note
78-16856-01
Safety Overview
•Obtaining Technical Assistance, page 26
•Obtaining Additional Publications and Information, page 27
Safety Overview
Warning IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device.
Statement 1071
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS

3
Catalyst 6500 Series Switch Content Switching Module with SSL Installation Note
78-16856-01
Safety Overview
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES

4
Catalyst 6500 Series Switch Content Switching Module with SSL Installation Note
78-16856-01
Safety Overview
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR

5
Catalyst 6500 Series Switch Content Switching Module with SSL Installation Note
78-16856-01
Safety Overview
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER

6
Catalyst 6500 Series Switch Content Switching Module with SSL Installation Note
78-16856-01
Safety Overview

7
Catalyst 6500 Series Switch Content Switching Module with SSL Installation Note
78-16856-01
Front Panel Description
Front Panel Description
These sections describe the physical attributes of the CSM-S:
•LEDs, page 8
•RJ-45 Connector, page 9
•SSL Connector, page 9
Figure 1 shows the CSM-S front panel.
Figure 1 Content Switching Module with SSL Front Panel
Note The RJ-45 connector is covered by a removable plate.
RJ-45
Status
LED
113438
SSL Certificate Management
Connector
Crypto

8
Catalyst 6500 Series Switch Content Switching Module with SSL Installation Note
78-16856-01
Front Panel Description
Note You are required to make initial SSL daughter card configurations through a direct connection to the
CSM-S Certificate Management port (Cert. Mgt). After the initial configurations, you can make an SSH
or Telnet connection to further configure the module. See Chapter 5 in the Catalyst 6500 Series Content
Switching Module with SSL Installation and Configuration Note.
LEDs
When the CSM-S powers up, it initializes various hardware components and communicates with the
supervisor engine. The Status LED indicates the supervisor engine operations and the initialization
results. During the normal initialization sequence, the status LED changes from off to red, orange, and
green. The SSL daughter card Crypto LED is unused in this release.
Note For more information on the supervisor engine LEDs, refer to the Catalyst 6500 Series Switch Module
Installation Guide.
Table 1 describes the Status LED operation.
Table 1 Content Switching Module LEDs
LED Color Description
Status Off •The module is waiting for the supervisor engine to provide power.
•The module is not online.
•The module is not receiving power, which could be caused by the following:
– Power is not available to the CSM-S.
– Module temperature is over the limit1.
1. Enter the show environment temperature mod command to display the temperature of each of the four sensors on the CSM-S.
Red •The module is released from reset by the supervisor engine and is booting.
•If the boot code fails to run, the LED stays red after power up.
Orange •The module is initializing hardware or communicating with the supervisor engine.
•A fault occurred during the initialization sequence.
•The module has failed to download its Field Programmable Gate Arrays (FPGAs) on power up but
continues with the remainder of the initialization sequence and provides the module online status from
the supervisor engine.
•The module has not received module online status from the supervisor engine. This problem could be
caused by the supervisor engine detecting a failure in an external loopback test that it issued to the
CSM-S.
Green •The module is operational; the supervisor engine has provided module online status.
Green
to
orange
•The module is disabled through the supervisor engine CLI 2using the set module disable mod
command.
2. CLI = command-line interface.
Crypto None. •Not used. Reserved for future releases.

9
Catalyst 6500 Series Switch Content Switching Module with SSL Installation Note
78-16856-01
Environmental and System Requirements
RJ-45 Connector
The RJ-45 connector, which is covered by a removable plate, is used to connect a management station
device or a test device. This connector is used by field engineers to perform testing and to obtain dump
information.
SSL Connector
The Certificate Management (Cert. Mgt.) port connector is used for SSL certificate management and is
available to make the necessary connection to the SSL daughter card for initial configuration purposes.
After the initial configurations, you can make an SSH or Telnet connection to further configure the
module. See Chapter 5 in the Catalyst 6500 Series Content Switching Module with SSL Installation and
Configuration Note.
Environmental and System Requirements
These sections describe the environmental and system requirements:
•Environmental Requirements, page 9
•System Requirements, page 10
•Memory Requirements, page 10
•Power Supply, page 10
•Hardware Supported, page 10
•Software Requirements, page 11
•Software Compatibility, page 11
Environmental Requirements
Table 2 lists the environmental requirements for the CSM-S.
Table 2 CSM-S Environmental Requirements
Item Specification
Temperature, ambient operating 0oto 40oC (32o to 104oF)
Temperature, ambient nonoperating –40oto 70oC (–40o to 158oF)
Humidity (RH), ambient (noncondensing)
operating
10% to 90%
Nonoperating relative humidity (noncondensing) 5% to 95%

10
Catalyst 6500 Series Switch Content Switching Module with SSL Installation Note
78-16856-01
Environmental and System Requirements
System Requirements
Before you install the CSM-S in the Catalyst 6500 series switch, make sure that the switch meets the
hardware and software requirements listed in this section.
Caution You can use the Multilayer Switch Feature Card (MSFC2), which is internal to the Catalyst 6500 series
switch, to route traffic on either the client side or the server side of the CSM-S, but not both
simultaneously (unless policy-based routing is used).
Memory Requirements
The CSM-S memory is not configurable.
Power Supply
You can place the CSM-S in any slot in the Catalyst 6500 series chassis except for the slots that are
occupied by the supervisor engine and the standby supervisor engine. The CSM-S operates on power that
is supplied by the chassis. Up to four CSM-S modules can be supported by each switch chassis.
Hardware Supported
Before you can use the Catalyst 6500 series CSM-S, you must have a Supervisor Engine 2 with an
MSFC2 and any module that has ports to connect server and client networks.
Caution The WS-X6066-SLB-S-K9 CSM-S are not fabric enabled, but the module can operate in a fabric-enabled
chassis like any other nonfabric module.
Table 3 lists the supported hardware and software for the CSM-S.
Table 3 Supported Hardware and Software
Product Number MinimumCisco
IOS Release
Recommended
Cisco IOS Release
Recommended
Catalyst OS Releases
Content Switching Module
Supervisor Engine 2 with MSFC2 12.2(18)SXD 12.2(18)SXD Not applicable
Console Cable
72-876-01 Not applicable
Accessory Kit
800-05097-01 Not applicable