Cisco Meraki MS225 Series User manual

MS225 Series nstallation Guide
About this Guide
This guide provides instruction on how to install and configure your MS225 series switch. This guide also provides
mounting instructions and limited troubleshooting procedures. For more switch installation guides, refer to the
switch installation guides section on our documentation website.
Model number Description
MS225-24 Stackable Layer-2 24-port gigabit Ethernet switch with 4 SFP+ interfaces
MS225-24P Stackable Layer-2 24-port gigabit Ethernet 370W PoE switch with 4 SFP+
interfaces
MS225-48 Stackable Layer-2 48-port gigabit Ethernet switch with 4 SFP+ interfaces
MS225-48LP Stackable Layer-2 48-port gigabit Ethernet 370W PoE switch with 4 SFP+
interfaces
MS225-48FP Stackable Layer-2 48-port gigabit Ethernet 740W PoE switch with 4 SFP+
interfaces
Product Overview
Physical Specifications
MS225-24 MS225-24P MS225-48 MS225-48LP MS225-48FP
1

1GbE RJ45 24 24 48 48 48
10GbE SFP+ 4 4 4 4 4
10G Hardware Stack Port 2 2 2 2 2
Dedicated Mgmt Interface 1 1 1 1 1
PoE/PoE+ Capable - Yes, 370W - Yes, 370W Yes, 740W
Power Supply Fixed nternal Fixed nternal Fixed nternal Fixed nternal Fixed nternal
Redundant Power Supply External RPS*
(optional)
External RPS*
(optional)
External RPS*
(optional)
External RPS*
(optional)
External RPS*
(optional)
Fan Operation Fanless Operation Fixed nternal Fanless
Operation Fixed nternal Fixed nternal
Power Input 100 - 240 VAC,
47-63 H
100 - 240 VAC,
47-63 Hz
100 - 240 VAC,
47-63 Hz
100 - 240 VAC, 47-63
Hz
100 - 240 VAC, 47-63
Hz
Power Consumption 15 - 882W 15 - 882W 15 - 882W 15 - 882W 15 - 882W
Power Load (idle/max) 15 / 24 W 21 / 448 W 25 / 42 W 53 / 490 W 54 / 882 W
Operating Temperature 23 °F - 122 °F
-5°C - 50°C
23 °F - 122 °F
-5°C - 50°C
23 °F - 122 °F
-5°C - 50°C
23 °F - 122 °F
-5°C - 50°C
23 °F - 122 °F
-5°C - 50°C
Storage and
Transportation Temperature [°F and °C] [°F and °C] [°F and °C] [°F and °C]
Humidity 5% to 95% 5% to 95% 5% to 95% 5% to 95% 5% to 95%
Mounting 1U Rack Mount 1U Rack Mount 1U Rack Mount 1U Rack Mount 1U Rack Mount
Product View and Physical Features
Front Panel
2

MS225-24 Series front panel
MS225-48 Series front panel
Back Panel
MS225 Series back panel
Factory Reset Button
f the button is pressed and held for at least five seconds and then released, the switch will reboot and be restored to its
original factory settings by deleting all configuration information stored on the unit.
Ports and Status Indicators
The MS uses LEDs to inform the user of the device's status. When the device powers on, all the nternet LEDs flash
twice. Additional functions are described below, from left to right.
Front Panel Components
Function LED Status Meaning
Power Solid orange Switch is unable to connect to the Meraki cloud
Flashing white Firmware upgrade in process
Solid white Switch is fully operational and connected to the Meraki cloud
Off Switch does not have power
Restore N/A Restore button to clear switch P and local configuration settings
3

Switch Ports Off No link is detected on this port
Solid orange 10/100 Mbps (1 Gbps on SFP+)
Solid green 1 Gbps (10 Gbps on SFP+)
n addition, there is a RESTORE button available on the front panel.
nsert a paperclip if a restore is required.
• A brief, momentary press: To delete a downloaded configuration and reboot.
• Press and hold for more than 10 sec: To force the unit into a full factory restore.
Back Panel Components
Function LED Status Meaning
Management Interface Green Connected, used for easy access to the local status page
Stack Ports Green QSFP stacking cable is connected
Off No link is detected on this port
22-Pin Redundant Power Supply
Connector N/A RPS2300 can be connected to provide redundant power in case of a failover
Power cords may be ordered separately.
Equipment is to be used only in a restricted access location and installed/operated only by trained service personnel.
RPS2300 Redundant Power Supply (Optional)
The MS225 series supports connecting the Cisco RPS2300 for optional power redundancy. MS225 series models
support failover and reversion to main power once it has been restored. The following Cisco part numbers are
supported:
4

Part number Description
PWR-RPS2300 RPS Chassis
C3K-PWR-750WAC 750W RPS Power supply (see recommendations)
C3K-PWR-1150WAC 1150W RPS Power supply (see recommendations)
CAB-RPS2300-E= RPS 22-pin cable
RPS power supply matrix
Switch Model Full power load [idle/max including PoE]
MS225-24 15 / 24 W
MS225-24P 21 / 448 W
MS225-48 25 / 42 W
MS225-48LP 53 / 490 W
MS225-48FP 54 / 882 W
Only the RPS2300 chassis (PWR-RPS2300) and accessories are supported. For more information, see the RPS2300
datasheet
Package contents
n addition to the MS switch, the following are provided:
Rack Mount Kit includes:
▪ US 12-24 mounting screws and cage nuts, 5 of each
▪ NTL M5 mounting screws and cage nuts, 5 of each
▪ NTL M6 mounting screws and cage nuts, 5 of each
5

▪ Mounting washers
Note: MS225 does not include stacking cables. Stacking cables sold separately.
Safety and Warnings
These operations are to be taken with respect to all local laws. Please take the following into consideration for safe
operation:
• Power off the unit before you begin. Read the installation instructions before connecting the system to the power
source.
• Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with
standard practices for preventing accidents.
• Read the mounting instructions carefully before beginning installation. Failure to use the correct hardware or to
follow the correct procedures could result in a hazardous situation to people and damage to the system.
• This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective
device is rated not greater than: 15 A, 125 Vac, or 10A, 240 Vac.
• Please only power the device with the provided power cables to ensure regulatory compliance.
Pre-install Preparation
You should complete the following steps before going on-site to perform an installation.
Configure your Dashboard Network
The following is a brief overview only of the steps required to add a switch to your network. For detailed instructions
about creating, configuring and managing Meraki networks, refer to the online documentation
(documentation.meraki.com).
1. Login to http://dashboard.meraki.com. f this is your first time, create a new account.
2. Find the network to which you plan to add your switches or create a new network.
3. Add your switches to your network. You will need your Meraki order number (found on your invoice) or the serial
number of each switch, which looks like Qxxx-xxxx-xxxx, and is found on the bottom of the unit. You will also need
your Enterprise license key, which you should have received via email.
4. Go to the map / floor plan view and place each switch on the map by clicking and dragging it to the location where
you plan to mount it.
Check and Set Firmware
To ensure your switch performs optimally immediately following installation, it is recommended that you facilitate a
firmware upgrade prior to mounting your switch.
1. Attach your switch to power and a wired nternet connection.
6

2. The switch will turn on and the power LED will glow solid orange.
3. f the unit requires an upgrade, the power LED will begin blinking white until the upgrade is complete, at which
point the LED will turn solid white. You should allow at least a few minutes for the firmware upgrade to complete,
depending on the speed of your internet connection.
Check and Configure Upstream Firewall Settings
f a firewall is in place, it must allow outgoing connections on particular ports to particular P addresses. The most
current list of outbound ports and P addresses for your particular organization can be found on the firewall configuration
page in your dashboard.
Assigning an P Address
All switches must be assigned routable P addresses. These P addresses can be dynamically assigned via DHCP or
statically assigned.
Dynamic Assignment
When using DHCP, the DHCP server should be configured to assign a static P address for each MAC address
belonging to a Meraki switch. Other features of the network, such as 802.1X authentication, may rely on the property
that the switches have static P addresses.
Static Assignment
Static Ps are assigned using the local web server on each switch. The following procedure describes how to set the
static P:
1. Using a client machine (e.g., a laptop), connect to the switch over a wired connection.
2. Using a web browser on the client machine, access the switch’s built-in web server by browsing
to http://my.meraki.com. Alternatively, browse to http://1.1.1.100
3. Click on the “Uplink Configuration” tab. Log in. The default login is the serial number (e.g. Qxxx-xxxx-xxxx), with no
password (e.g., Q2DD-551C-ZYW3).
4. Configure the static P address, net mask, gateway P address and DNS servers that this switch will use on its
management connection.
5. f necessary, reconnect the switch to the LAN.
Static IP via DHCP Reservations
nstead of associating to each Meraki switch individually to configure static P addresses, an administrator can assign
static P addresses on the upstream DHCP server. Through “DHCP reservations,” P addresses are “reserved” for the
MAC addresses of the Meraki switches. Please consult the documentation for the DHCP server to configure DHCP
reservations.
7

nstallation nstructions
Note: Each switch comes with a graphical instruction pamphlet within the box. This pamphlet contains detailed step by
step guides and images to assist in the physical install of the switch.
1. nstall the mounting cage nuts in the rack being used for the switch.
2. Separate the rack mount rails, and install the rack mount rails channel onto the rack.
8

3. Attach the rack mount rail to the sides of the switch.
9

4. nsert the rack mount rail into the rack mount rail channel.
10