Cisco Small Business SF200-24 Instruction Manual

Cisco Small Business 200 Series Smart Switch
Administration Guide Release 1.1
10/100 Switches SF200-24, SF200-24P, SF200-48, SF200-48P
Gigabit Switches SG200-18, SG200-26, SG200-26P, SG200-50, SG200-50P
ADMINISTRATION
GUIDE

Cisco Small Business 200 1.1 Series Smart Switch Administration Guide 2
Contents
Chapter 1: Getting Started 1
Starting the Web-based Switch Configuration Utility 1
Launching the Configuration Utility 1
Logging In 2
Password Expiration 5
Logging Out 5
Quick Start Switch Configuration 6
Window Navigation 7
Application Header 7
Management Buttons 9
Chapter 2: Viewing Statistics 12
Viewing Ethernet Interface 12
Viewing Etherlike Statistics 15
Viewing 802.1X EAP Statistics 17
Managing RMON Statistics 18
Viewing RMON Statistics 19
Configuring RMON History 21
Viewing the RMON History Table 23
Defining RMON Events Control 25
Viewing the RMON Events Logs 27
Defining RMON Alarms 28
Chapter 3: Managing System Logs 31
Setting System Log Settings 31
Setting Remote Logging Settings 34
Viewing Memory Logs 36
RAM Memory 36
Flash Memory 38

Cisco Small Business 200 1.1 Series Smart Switch Administration Guide 3
Contents
Chapter 4: Managing System Files 39
Upgrade/Backup Firmware/Language 42
Downloading or Backing-up a Configuration or Log 45
Displaying Configuration File Properties 49
Copying Configuration Files 50
Setting DHCP Auto Configuration 52
Chapter 5: System Time 55
System Time Options 56
Configuring System Time 57
Adding an SNTP Server 59
Defining SNTP Authentication 63
Chapter 6: General Administrative Information and Operations 66
System Information 67
Displaying the System Summary 67
Configuring the System Settings 69
Switch Models 70
Rebooting the Switch 71
Monitoring the Fan Status 73
Defining Idle Session Timeout 74
Pinging a Host 75
Chapter 7: Configuring Discovery 77
Configuring Bonjour Discovery 77
Configuring LLDP 78
Setting LLDP Properties 80
Editing LLDP Port Settings 81
LLDP MED Protocol 85
Setting LLDP MED Network Policy 85
Configuring LLDP MED Port Settings 88

Cisco Small Business 200 1.1 Series Smart Switch Administration Guide 4
Contents
Displaying LLDP Port Status 90
Displaying LLDP Local Information 92
Displaying LLDP Neighbors Information 96
Accessing LLDP Statistics 101
LLDP Overloading 102
Chapter 8: Port Management 106
Configuring Ports 106
Port Management Workflow 106
Setting the Basic Port Configuration 107
Configuring Link Aggregation 111
Static and Dynamic LAG Workflow 112
Defining LAG Management 113
Defining Member Ports in a LAG 114
Configuring LAG Settings 115
Configuring LACP 117
Setting Port LACP Parameter Settings 118
Green Ethernet 120
Setting Global Green Ethernet Properties 121
Setting Green Ethernet Properties for Ports 123
Chapter 9: Managing Device Diagnostics 125
Testing Copper Ports 125
Displaying Optical Module Status 129
Configuring Port and VLAN Mirroring 131
Viewing CPU Utilization 134
Chapter 10: Managing Power-over-Ethernet Devices 135
PoE on the Switch 135
PoE Features 135
PoE Operation 136
PoE Configuration Considerations 136

Cisco Small Business 200 1.1 Series Smart Switch Administration Guide 5
Contents
Configuring PoE Properties 137
Configuring the PoE Power, Priority, and Class 139
Chapter 11: VLAN Management 143
VLANs 143
Configuring Default VLAN Settings 145
Creating VLANs 147
Configuring VLAN Interface Settings 150
Defining VLAN Membership 153
Configuring Port to VLAN 154
Configuring VLAN to Port 155
Viewing VLAN Membership 158
Voice VLAN 159
Voice VLAN Options 160
Configuring Voice VLAN Properties 161
Configuring Telephony OUI 163
Chapter 12: Configuring the Spanning Tree Protocol 165
STP Flavors 165
Configuring STP Status and Global Settings 166
Defining Spanning Tree Interface Settings 169
Configuring Rapid Spanning Tree Settings 172
Chapter 13: Managing MAC Address Tables 176
Configuring Static MAC Addresses 176
Dynamic MAC Addresses 178
Configuring Dynamic MAC Address Parameters 179
Querying Dynamic Addresses 179
Chapter 14: Configuring Multicast Forwarding 182
Multicast Forwarding 182

Cisco Small Business 200 1.1 Series Smart Switch Administration Guide 6
Contents
Typical Multicast Setup 183
Multicast Operation 183
Multicast Registration 184
Multicast Address Properties 185
Defining Multicast Properties 185
Adding MAC Group Address 188
Adding IP Multicast Group Address 192
Configuring IGMP Snooping 195
Configuring MLD Snooping 199
Viewing GMP/MLD IP Multicast GroupsI 202
Defining Multicast Router Ports 203
Defining Forward All Multicast 205
Defining Unregistered Multicast Settings 207
Chapter 15: Configuring IP Information 210
Management and IP Interfaces 210
IP Addressing 212
Defining an IPv4 Interface 213
Defining IPv6 Global Configuration 215
Defining an IPv6 Interface 216
Defining IPv6 Addresses 218
Viewing the IPv6 Default Router List 220
Configuring IPv6 Tunnels 223
Defining IPv6 Neighbors Information 225
Viewing IPv6 Route Tables 229
Configuring ARP 230
Domain Name Systems 233
Defining DNS Servers 233
Mapping DNS Hosts 235

Cisco Small Business 200 1.1 Series Smart Switch Administration Guide 7
Contents
Chapter 16: Configuring Security 238
Defining Users 240
Setting User Accounts 240
Setting Password Complexity Rules 242
Configuring RADIUS Parameters 244
Configuring Management Access Authentication 248
Defining Access Profiles 250
Displaying, Adding, or Activating an Access Profile 251
Defining Profile Rules 254
Configuring TCP/UDP Services 257
Defining Storm Control 259
Configuring Port Security 262
Configuring 802.1X 265
802.1X Parameters Workflow 266
Defining 802.1X Properties 267
Defining 802.1X Port Authentication 268
Defining Host and Session Authentication 271
Viewing Authenticated Hosts 274
Chapter 17: Configuring Quality of Service 275
QoS Features and Components 275
Configuring QoS 277
Displaying QoS Properties 277
Defining QoS InterfaceSettings 279
Configuring QoS Queues 281
Mapping CoS/802.1p to a Queue 283
Mapping DSCP to Queue 285
Configuring Bandwidth 286
Configuring Egress Shaping per Queue 288
Managing QoS Statistics 290
Viewing Queues Statistics 290

1
Cisco Small Business 200 1.1 Series Smart Switch Administration Guide 1
Getting Started
This section provides an introduction to the user interface, and includes the
following topics:
•Starting the Web-based Switch Configuration Utility
•Quick Start Switch Configuration
•Window Navigation
Starting the Web-based Switch Configuration Utility
This section describes how to navigate the web-based switch configuration utility.
If you are using a pop-up blocker, make sure it is disabled.
Browser Restrictions
Browsers have the following restrictions:
•If you are using Internet Explorer 6, you cannot directly use an IPv6 address
to access the switch. You can, however, use the DNS (Domain Name
System) server to create a domain name that contains the IPv6 address,
and then use that domain name in the address bar in place of the IPv6
address.
•In Firefox, the automatic pop-up on top option is disabled by default. Certain
add-ons enable this feature during installation. To disable this option, go to
ToolsOptionsContentEnable JavaScriptAdvance.
•If you have multiple IPv6 interfaces on your management station, use the
IPv6 global address instead of IPv6 link local address to access the switch
from your browser.

Getting Started
Starting the Web-based Switch Configuration Utility
Cisco Small Business 200 1.1 Series Smart Switch Administration Guide 2
1
Launching the Configuration Utility
To open the user interface:
STEP 1 Open a Web browser.
STEP 2 Enter the IP address of the switch you are configuring in the address bar on the
browser, and then press Enter. The
Login page opens.
NOTE When the switch is using the factory default IP address of 192.168.1.254, its power
LED flashes continuously. When the switch is using a DHCP assigned IP address or
an administrator-configured static IP address, the power LED is on solid.
Logging In
Logging In
The default username is cisco and the default password is cisco. The first time
that you log in with the default username and password, you are required to enter
a new password.
To log in to the device configuration utility:
STEP 1 Enter the username/password. The password can contain up to 64 ASCII
characters. Password-complexity rules are described in the Setting Password
Complexity Rules section of the Configuring Security chapter.
STEP 2 If you are not using English, select the desired language from the Language drop-
down menu. To add a new language to the switch or update a current one, refer to
the Upgrade/Backup Firmware/Language section.
STEP 3 If this is the first time that you logged on with the default user ID (cisco) and the
default password (cisco) or your password has expired, the
Change Password
Page opens. See Password Expiration for additional information.
STEP 4 Choose whether to select Disable Password Complexity Enforcement or not.
For more information on password complexity, see the Setting Password
Complexity Rules section.
STEP 5 Enter the new password and click Apply.
When the login attempt is successful, the Getting Started page opens.

Getting Started
Starting the Web-based Switch Configuration Utility
Cisco Small Business 200 1.1 Series Smart Switch Administration Guide 3
1
If you entered an incorrect username or password, an error message is displayed
and the Login page remains displayed on the window. If you are having problems
logging in, please see the Launching the Configuration Utility section in the
Administration Guide for additional information.
Select Don’t show this page on startup to prevent the
Getting Started page from
being displayed each time that you logon to the system. If you select this option,
the System Summary page is opened instead of the Getting Started page.
Password Expiration
Password Expiration
The New Password page is displayed:
•The first time you access the switch with the default username cisco and
password cisco. This page forces you to replace the factory default
password.
•When the password expires, this page forces you to select a new
password.
Logging Out
Logging Out
By default, the application logs out after ten minutes of inactivity. You can change
this default value as described in the Defining Idle Session Timeout section in the
General Administrative Information and Operations chapter.
!
CAUTION Unless the Running Configuration is copied to the Startup Configuration, all
changes made since the last time the file was saved are lost if the switch is
rebooted. Save the Running Configuration to the Startup Configuration before
logging off to preserve any changes you made during this session.
A flashing red X icon displayed to the left of the Save application link indicates that
Running Configuration changes have been made that have not yet been saved to
the Startup Configuration file. The flashing can be disabled by clicking on the
Disable Save Icon Blinking button on the Copy/Save Configuration page
When the switch auto-discovers a device, such as an IP phone, it configures the