Cisco Catalyst IW9167I Manual

Cisco Catalyst IW9167I Heavy Duty Access Point Hardware Installation
Guide
First Published: 2023-10-18
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

©2023 Cisco Systems, Inc. All rights reserved.

CONTENTS
Preface vii
PREFACE
About this Guide vii
Conventions vii
Related Documentation viii
Communications, Services, and Additional Information viii
Cisco Bug Search Tool viii
Documentation Feedback viii
About Cisco Catalyst IW9167I Heavy Duty Access Point 1
CHAPTER 1
Introduction to Cisco Catalyst IW9167I Heavy Duty Access Point 1
Cisco Catalyst IW9167I Heavy Duty Access Point Features 1
Connectors and Ports 2
4-Pin Micro-Fit Connector for DC Power 3
M12-RJ45 Adapter 3
M12-PWR Adapter 4
Power Sources 5
Power Adapters 5
Power Injectors 6
Ethernet (PoE) Ports 6
SFP Option 6
Antennas and Radios 7
Internal Antennas and GNSS Receiver 7
IW9167I (Internal Antenna) Radiation Patterns 8
Unpacking Your Access Point 13
CHAPTER 2
Package Contents 13
Cisco Catalyst IW9167I Heavy Duty Access Point Hardware Installation Guide
iii

Unpacking the Access Point 13
Cisco Orderable Accessories 13
Installation Overview 15
CHAPTER 3
Performing a Preinstallation Configuration (Optional) 15
Preinstallation Checks and Installation Guidelines 17
Mounting the Access Point 18
Mounting Hardware 18
Mounting Bracket Part Numbers 18
Using the Integrated Flange Mounts 19
Using the DIN Rail Mounting Bracket 20
Pole Mounting the AP with Horizontal Bracket 23
Using the Pole Mounting Bracket 24
Using the Mounting Bracket AIR-ACCPMK3700= 24
Using the Mounting Bracket AIR-ACCPMK3700-2= 25
Attaching a Power Adapter 30
Attaching a Power Adapter Using the Mounting Bracket AIR-ACCPMK3700= 30
Attaching a Power Adapter Using the Mounting Bracket AIR-ACCPMK3700-2= 31
Grounding the Access Point 33
Powering the Access Point 34
Power Feature Matrix 35
Connecting a Power Injector 35
Connecting to the DC Power Port Using Cable Gland 36
Connecting DC Power Port Using M12 Adapter 37
Connecting Data Cables 39
Connecting an Ethernet Cable to the Access Point 39
Connecting to the RJ45 Port Using Cable Gland 39
Connecting to the RJ45 Port Using M12 Adapter 40
Connecting to the SFP Port of the Access Point 42
Connecting to SFP Port Using Cable Gland 42
Using M12 Adapter on SFP Port 44
Configuring and Deploying the Access Point 47
CHAPTER 4
Controller Discovery Process 47
Cisco Catalyst IW9167I Heavy Duty Access Point Hardware Installation Guide
iv
Contents

Deploying the Access Point in a Wireless Network 48
Checking the Access Point LEDs 48
Troubleshooting 51
CHAPTER 5
Using the Reset Button 51
Troubleshooting the Access Point to Controller Join Process 51
Important Information for Controller-based Deployments 52
Configuring DHCP Option 43 52
Safety Guidelines and Warnings 55
CHAPTER 6
Safety Instructions 55
FCC Safety Compliance Statement 56
Safety Precautions 56
Avoiding Damage to Radios in a Testing Environment 57
Performing Site Surveys 57
Declarations of Conformity and Regulatory Information 59
CHAPTER 7
Manufacturers Federal Communications Commission Declaration of Conformity Statement 59
Operation of Cisco Catalyst Access Points in México 60
VCCI Statement for Japan 60
Statement 191—Voluntary Control Council for Interference (VCCI) Class A Warning for Japan 60
ステートメント 191—日本向けVCCI クラス Aに関する警告 61
Guidelines for Operating Cisco Catalyst Access Points in Japan 61
Compliance Statement for Canada 62
Industry Canada 62
European Community, Switzerland, Norway, Iceland, and Liechtenstein 62
United Kingdom Compliance 63
Administrative Rules for Cisco Catalyst Access Points in Taiwan 64
Declaration of Conformity for RF Exposure 64
Generic Discussion on RF Exposure 64
This Device Meets International Guidelines for Exposure to Radio Waves 65
This Device Meets FCC Guidelines for Exposure to Radio Waves 65
This Device Meets the Industry Canada Guidelines for Exposure to Radio Waves 66
Cisco Catalyst IW9167I Heavy Duty Access Point Hardware Installation Guide
v
Contents

Cet appareil est conforme aux directives internationales en matière d'exposition aux fréquences
radioélectriques 66
Additional Information on RF Exposure 67
Declaration of Conformity Statements 67
Cisco Catalyst IW9167I Heavy Duty Access Point Hardware Installation Guide
vi
Contents

Preface
This preface describes this guide and provides information about the conventions used in this guide, and
related documentation.
It includes the following sections:
•About this Guide, on page vii
•Conventions, on page vii
•Related Documentation, on page viii
•Communications, Services, and Additional Information, on page viii
About this Guide
This guide provides instructions to install your Cisco Access Point and provides links to resources that can
help you configure it. This guide also provides mounting instructions and troubleshooting information.
Conventions
This document uses the following conventions for notes, cautions, and safety warnings. Notes and cautions
contain important information that you should know.
Means reader take note. Notes contain helpful suggestions or references to material not covered in the manual.
Note
Means reader be careful. Cautions contain information about something you might do that could result in
equipment damage or loss of data.
Caution
Safety warnings appear throughout this guide in procedures that, if performed incorrectly, can cause physical
injuries. A warning symbol precedes each warning statement.
Warning
Cisco Catalyst IW9167I Heavy Duty Access Point Hardware Installation Guide
vii

Related Documentation
All user documentation for the Catalyst IW9167I Heavy Duty access point is available at the following URL:
https://www.cisco.com/c/en/us/support/wireless/catalyst-iw9167-series/series.html
For detailed information and guidelines about configuring and deploying your access point in a wireless
network, see the relevant release of Wireless Controller configuration guide at the following URL:
https://www.cisco.com/c/en/us/support/wireless/catalyst-9800-series-wireless-controllers/
products-installation-and-configuration-guides-list.html
Communications, Services, and Additional Information
• To receive timely, relevant information from Cisco, sign up at Cisco Profile Manager.
• To get the business impact you’re looking for with the technologies that matter, visit Cisco Services.
• To submit a service request, visit Cisco Support.
• To discover and browse secure, validated enterprise-class apps, products, solutions, and services, visit
Cisco DevNet.
• To obtain general networking, training, and certification titles, visit Cisco Press.
• To find warranty information for a specific product or product family, access Cisco Warranty Finder.
Cisco Bug Search Tool
Cisco Bug Search Tool (BST) is a gateway to the Cisco bug-tracking system, which maintains a comprehensive
list of defects and vulnerabilities in Cisco products and software. The BST provides you with detailed defect
information about your products and software.
Documentation Feedback
To provide feedback about Cisco technical documentation, use the feedback form available in the right pane
of every online document.
Cisco Catalyst IW9167I Heavy Duty Access Point Hardware Installation Guide
viii
Preface
Related Documentation

CHAPTER 1
About Cisco Catalyst IW9167I Heavy Duty Access
Point
•Introduction to Cisco Catalyst IW9167I Heavy Duty Access Point, on page 1
•Cisco Catalyst IW9167I Heavy Duty Access Point Features, on page 1
•Connectors and Ports, on page 2
•Power Sources, on page 5
•SFP Option, on page 6
•Antennas and Radios, on page 7
Introduction to Cisco Catalyst IW9167I Heavy Duty Access Point
The Cisco Catalyst IW9167I Heavy Duty Access Point (hereafter referred to as IW9167I) is designed to make
wireless deployments simple in outdoor and industrial environments. It is built with a cast-aluminum case
that can handle water, dust, and extreme temperatures. It includes built-in antennas and supports Wi-Fi 6E to
enable higher density, higher throughput, more channels, power efficiency, and improved security.
IW9167I includes 6 GHz hardware support.
The AP hardware is supported on the following platforms:
• Cisco DNA Center on-premises
• Cisco Catalyst stack
A full listing of the AP's features and specifications is provided in the Cisco Catalyst IW9167 Heavy Duty
Access Point Data Sheet.
Cisco Catalyst IW9167I Heavy Duty Access Point Features
The Cisco Catalyst IW9167I Heavy Duty Access Point has the following features:
• 2 GB DDR4 memory, 1 GB NAND Flash
• Tri radios—2.4 GHz, 5 GHz, 6 GHz
• Integrated antenna—2.4 GHz 4x4:4SS, 5 GHz 4x4:4SS, 6 GHz 4x4:4SS,
Cisco Catalyst IW9167I Heavy Duty Access Point Hardware Installation Guide
1

• 2.4 GHz IoT Bluetooth Low Energy (BLE) radio
• Integrated GNSS
• 1 x multi-Gigabit (mGig) copper Ethernet port (supporting PoE, including IEEE 802.3at/bt, Cisco UPoE,
100 Mbps/1 Gbps/2.5 Gbps/5 Gbps)
• 1 x SFP interface—Supports up to 10 Gbps
• Optional M12 adapter for network and power interfaces
• Dual power input options—PoE-in and 24 - 48VDC
• Dual mounting options—Pole or wall mount
• IP67 rating
• Indoor and outdoor mode operation supported in different countries as shown in the following table:
Indoor and outdoorFCC
OutdoorIC
Indoor and outdoorCE
OutdoorC-tick
OutdoorTelec
Connectors and Ports
The following figure shows the available ports on the AP front panel.
Figure 1: IW9167I Front Panel Connectors and Ports
Cisco Catalyst IW9167I Heavy Duty Access Point Hardware Installation Guide
2
About Cisco Catalyst IW9167I Heavy Duty Access Point
Connectors and Ports