CITO AI-CT-12-F User manual

Thank you for selecting the Cito Thaw. This
electronic device automatically heats and
maintains an accurate water temperature.
Cito Thaw was designed to give you years of
trouble free service.
THAW
INSTRUCTION MANUAL
96.8OF / 36OC
TWO YEAR WARRANTY
Any Cito Warm Water Thaw Device found to be defective
in material or workmanship within 2 years from date of
purchase will be repaired or replaced free of charge,
when shipped prepaid to the factory. Warranty does not
include breakage of the thermos liner.
Note: Model AI-CT-120 and AI-CT-240 do not
use with a portable Generators.
Keep Electrical Connections Clean and Dry
SHIPPING INSTRUCTIONS
Package to avoid damage, label
FRAGILE - GLASS
and ship to:
N8779 COUNTY ROAD X •P.O. BOX 90
WATERTOWN, WI 53094 U.S.A.
TEL: [phone] •FAX: [phone]
www.citoai.com •[e-mail]
CT-I-4-C-1-10K
PROCEDURE TO CHECK WATER TEMP.
Place THAWMONITOR in water for a minimum
of 10 seconds. See instructions on back of
THAWMONITOR to determine temperature of
water bath.
4. With the correct water temperature you are
now ready to thaw semen in your Cito Thaw.
5. NOTE: New Cito Thaw units have an internal
temperature adjustment knob. Your Cito Thaw
has been factory calibrated to 96.8OF/36OC.
However, if you desire to change the preset
temperature, you may readjust it by removing
the 7 screws on the bottom of the unit and
adjusting the knob clockwise for warmer and
counter-clockwise for cooler temperatures. Turn
temperature adjustment knob a little at a time
and allow unit to stabilize before checking
temperature again.
6. If unit does not maintain proper temperature,
return unit for repair or replacement. Ship to
factory with your comments and your address.
TO OPERATE
1. Fill Cito Thaw with clean tap water. Plug
cord into correct voltage source as indicated
on base of unit. Wait for thaw device to heat
up to proper temperature. Your water temper-
ature when you started determines the exact
warm up time approximately 2OF/1.1OC per
minute.
50Owater temp. to 96.8OF/36OC = approx. 23 min.
60Owater temp. to 96.8OF/36OC = approx. 18 min.
70Owater temp. to 96.8OF/36OC = approx. 13 min.
80Owater temp. to 96.8OF/36OC = approx. 8 min.
2. Green ready light must be on, indicating
unit is up to temperature.
3. Agitate the water by taking the basket and
moving it up and down several times to assure
water temperature is consistent through the
water bath.
AI-CT-12-F CITO THAW 12VDC - F TEMP. READ OUT
AI-CT-12-C CITO THAW 12VDC - C TEMP. READ OUT
AI-CT-120-F CITO THAW 12VDC-120VAC - F READ OUT
AI-CT-240-C CITO THAW 12VDC-240VAC - C READ OUT
Power Supply Cord
240V Cord
120V Cord
12V Cord
(lighter plug)

Thank you for selecting the Cito Thaw. This
electronic device automatically heats and
maintains an accurate water temperature.
Cito Thaw was designed to give you years of
trouble free service.
THAW
INSTRUCTION MANUAL
96.8OF / 36OC
TWO YEAR WARRANTY
Any Cito Warm Water Thaw Device found to be defective
in material or workmanship within 2 years from date of
purchase will be repaired or replaced free of charge,
when shipped prepaid to the factory. Warranty does not
include breakage of the thermos liner.
Note: Model AI-CT-120 and AI-CT-240 do not
use with a portable Generators.
Keep Electrical Connections Clean and Dry
SHIPPING INSTRUCTIONS
Package to avoid damage, label
FRAGILE - GLASS
and ship to:
N8779 COUNTY ROAD X •P.O. BOX 90
WATERTOWN, WI 53094 U.S.A.
TEL: [phone] •FAX: [phone]
www.citoai.com •[e-mail]
CT-I-4-C-1-10K
PROCEDURE TO CHECK WATER TEMP.
Place THAWMONITOR in water for a minimum
of 10 seconds. See instructions on back of
THAWMONITOR to determine temperature of
water bath.
4. With the correct water temperature you are
now ready to thaw semen in your Cito Thaw.
5. NOTE: New Cito Thaw units have an internal
temperature adjustment knob. Your Cito Thaw
has been factory calibrated to 96.8OF/36OC.
However, if you desire to change the preset
temperature, you may readjust it by removing
the 7 screws on the bottom of the unit and
adjusting the knob clockwise for warmer and
counter-clockwise for cooler temperatures. Turn
temperature adjustment knob a little at a time
and allow unit to stabilize before checking
temperature again.
6. If unit does not maintain proper temperature,
return unit for repair or replacement. Ship to
factory with your comments and your address.
TO OPERATE
1. Fill Cito Thaw with clean tap water. Plug
cord into correct voltage source as indicated
on base of unit. Wait for thaw device to heat
up to proper temperature. Your water temper-
ature when you started determines the exact
warm up time approximately 2OF/1.1OC per
minute.
50Owater temp. to 96.8OF/36OC = approx. 23 min.
60Owater temp. to 96.8OF/36OC = approx. 18 min.
70Owater temp. to 96.8OF/36OC = approx. 13 min.
80Owater temp. to 96.8OF/36OC = approx. 8 min.
2. Green ready light must be on, indicating
unit is up to temperature.
3. Agitate the water by taking the basket and
moving it up and down several times to assure
water temperature is consistent through the
water bath.
AI-CT-12-F CITO THAW 12VDC - F TEMP. READ OUT
AI-CT-12-C CITO THAW 12VDC - C TEMP. READ OUT
AI-CT-120-F CITO THAW 12VDC-120VAC - F READ OUT
AI-CT-240-C CITO THAW 12VDC-240VAC - C READ OUT
Power Supply Cord
240V Cord
120V Cord
12V Cord
(lighter plug)