Clare Controls CV-M3B10-ODI User manual

Doc ID - 337 • REV 04
Network Camera
Installation Guide
3 MP Mainline Bullet Camera
Model CV-M3B10-ODI
Last modified: 09/28/16

Copyright
© 28SEP16 Clare Controls. All rights reserved.
This document may not be copied in whole or in part or
otherwise reproduced without prior written consent from
Clare Controls, LLC., except where specifically permitted
under US and international copyright law.
Trademarks and
patents
The 3 MP Mainline Bullet Camera name is a trademark of
Clare Controls, LLC.
Other trade names used in this document may be
trademarks or registered trademarks of the manufacturers
or vendors of the respective products.
Manufacturer
Clare Controls, LLC.
7519 Pennsylvania Ave., Suite 104, Sarasota, FL 34243,
USA

i
Content
Description...1
Package contents...1
Safety instruction...1
Overview...4
Wiring...6
Installation...7
Before you start...7
Mounting...11
View angle adjusting...17
Zoom and focus adjusting...19
Setting the network camera over LAN...20
Accessing via a web browser...24
System requirements...24
Specifications...28
Regulatory information...30
Warranty information...32
Contact information...32

ii

1
Description
The 3 MP Mainline Bullet Camera is a high-resolution bullet IP
camera with 3 MP. It is the appropriate choice for outdoor
applications where image detail and/or wider coverage is
important. Capable of 2048 × 1536 resolution, the varifocal lens
incorporates 25 meter IR LEDs and zone-configurable backlight
compensation for use in varying light conditions. The PoE Bullet
Camera provides audio and alarm I/O and includes a micro SD
slot for up to 32 GB local memory.
Package contents
1X 12 VDC power supply
4X anchor screws
4X plastic anchors
1X drill template
1X hex tool (90 degree wrench)
1X composite video output pigtail adaptor (black wire with BNC
connector)
1X Ethernet weather housing
Safety instruction
Follow these instructions to ensure that the product is used
correctly and to avoid danger or property loss. Serious injury or
death may occur if any of the warnings are ignored. Injury or
equipment damage may occur if any of the cautions are
neglected.

2
WARNINGS
 In the use of the product, you must be in strict compliance
with the electrical safety regulations of the nation and
region.
 Refer to the technical specifications for detailed
information.
 Input voltage should meet both the SELV (Safety Extra
Low Voltage) and the Limited Power Source with 24 VAC
or 12 VDC according to the IEC60950-1 standard. Refer
to the technical specifications for detailed information.
 Do not connect several devices to one power adapter as
adapter overload may cause over-heating or a fire hazard.
 Make sure that the plug is firmly connected to the power
socket.
 When the product is mounted on the wall or ceiling, the
device should be firmly fixed.
 If smoke, odor, or noise rise from the device, turn off the
power at once and unplug the power cable. Contact the
service center.
 If the product does not work properly, contact your dealer
or the nearest service center. Never attempt to
disassemble the camera yourself. (We shall not assume
any responsibility for problems caused by unauthorized
repair or maintenance.)

3
CAUTIONS
 Make sure the power supply voltage is correct before
using the camera.
 Do not drop the camera or subject it to physical shock.
 Do not touch CMOS modules with fingers. If cleaning is
necessary, use a clean cloth with a bit of ethanol and
wipe it gently. If the camera will not be used for an
extended period, replace the lens cap to protect the
CMOS from dirt.
 Do not aim the camera at the sun or exceedingly bright
places. Blooming or smearing may occur (which is not a
malfunction), and affect the endurance of CMOS at the
same time.
 The CMOS may be burned out by a laser beam, so when
laser equipment is in use, make sure that the surface of
CMOS will not be exposed to the laser beam.
 Do not expose the camera to high electromagnetic
radiation, extremely hot or cold environments (the
operating temperature should be -30 to +60℃), dusty or
damp locations.
 To avoid heat accumulation, good ventilation is required
for operating environment.
 Keep the camera away from liquid while in use.
 When returning a camera, pack it in its original packing, or
similar packing materials.
 Improper use or replacement of the battery may result in
hazard of explosion. Replace it with the same or
equivalent type only. Dispose of used batteries according
to the instructions provided by the battery manufacturer.

4
Overview
Figure 1: Camera overview
(1) Sun shield
(2) Front cover
(3) Zoom and focus lever
(4) IR LED
(5) Lens
(6) Air vent
(7) Video output interface
(8) Integrated bracket
(9) Reset button
(10) SD card slot
(11) Power interface
(12) Network intrface
Note: To reset the default parameters to the camera, press and
hold the reset button and power on the camera. After powered
on, continue to press and hold the reset button for another 10
seconds.
5
4
10
9
7
3
8
6
1
2
12
11

5
The bullet camera supports audio and alarm functions. The
interfaces are shown in Figure 2.
Figure 2: Audio and alarm interfaces
(1) Audio
(2) Alarm
(1)
(2)

6
Wiring
Wire your bullet camera as shown in Figure 3.
Figure 3: Wiring

7
Installation
To ensure the camera operates properly, install the camera
according to the instructions below.
Before you start
 Make sure that the device in the package is in good
condition and all the assembly parts are included.
 Make sure that all the related equipment is powered off
during the installation.
 To determine the proper environmental operating
conditions, refer to Specifications on page 28.
 Make sure the power supply matches the required voltage
to avoid damage.
 If the product does not function properly, contact your
dealer or the nearest service center. Do not disassemble
the camera for repair or maintenance by yourself.
 Make sure that the wall is strong enough to withstand
three times the weight of the camera.

8
To mount the SD card:
1. Rotate the TW M3 × 5 screw counterclockwise about 3 to
4 rounds to loosen it. Slide the sun shield according to the
arrow direction, as shown in the figure below (left).
2. Remove the sun shield according to the arrow direction,
as shown in above (right).
Turn screw

9
3. Remove the front cover by rotating it counterclockwise, as
shown in above (right).
4. Insert the SD card to the SD card slot.
5. Place the cover back on the front of the camera and
rotate it clockwise, as shown. Reinstall the sun shield
according to the arrow direction, as shown below.
6. Slide the sun shield according to the arrow direction, as
shown below.
7. Rotate the TW M3 × 5 screw clockwise to tighten the sun
shield.
SD card slot

10
Note: For waterproofing, align the rotating label on the front
cover with that on the camera when you rotate the front cover
clockwise.
Rotating label

11
Mounting
This camera is equipped with a bracket on the bottom. It can be
mounted to a wall or ceiling directly or it can be mounted to a
wall with a junction box (not included) or a gang box (not
included).
To mount directly to the wall:
1. Attach the drill template to the wall where the camera is to
be mounted.
2. Drill screw holes in the wall according to the number one
holes of the drill template, shown below.

12
11
11
2
22
2
1:Screw Hole
for Bracket 2:Screw Hole
for Mounting
Base
Cable Hole
Screw Hole

13
1. If you need to route cables through the wall or ceiling, cut
a cable hole according to the drill template. Skip this step,
if you want to route the cables on the surface of the
ceiling.
2. Route the cables of the camera.
3. Secure the camera to the wall (or ceiling) with expansion
screws, as shown below.

14
To mount with a junction box:
1. Attach the drill template to the wall where the camera is to
be mounted.
2. Drill holes in the wall according to the number two holes
of the drill template.
3. If you need to route cables through the wall, cut a cable
hole according to the drill template. Skip this step, if you
want to route the cables on the surface of the wall or
ceiling.
4. Secure the junction box to the wall with expansion
screws.
5. Route the cables of the camera.
6. Connect the video output connector to the monitor and
the power connector to the power supply.
7. Adjust the image and focus. See “View angle adjusting”
and “Zoom and focus adjusting.”