Clare Controls CVP-B2D50-ODI User manual

DOC ID - 1451 • Rev 01
Network Camera
Installation Guide
2 MP Budget Mini-Dome Camera
Model CVP-B2D50-ODI
Last modified: 10/12/16

Copyright
© 12OCT16 Clare Controls. All rights reserved.
This document may not be copied in whole or in part or
otherwise reproduced without prior written consent from
Clare Controls, LLC., except where specifically permitted
under US and international copyright law.
Trademarks and
patents
The 2 MP Budget Mini Dome Camera name is a trademark
of Clare Controls, LLC.
Other trade names used in this document may be
trademarks or registered trademarks of the manufacturers
or vendors of the respective products.
Manufacturer
Clare Controls, LLC.
7519 Pennsylvania Ave., Suite 104, Sarasota, FL 34243,
USA

i
Contents
Description...1
Package contents...1
Safety instruction...1
Overview...4
Installation...5
Before you start...5
Setting the network camera over LAN...9
Accessing via web browser...14
System requirement...14
Specifications...17
Regulatory information...19
Warranty information...21
Contact information...21

ii

1
Description
The 2 MP Budget Mini Dome Camera is an affordable PoE 2
MP IP camera for outdoor use. The fixed-lens camera produces
high resolution 2 MP output at 1920 × 1080 in low illumination
with an IR LED range to 30 m. Features include 120dB True
wide dynamic range, zone-configurable backlight
compensation, and a vandal-resistant housing.
Package contents
1X 12 VDC power supply
3X anchor screws
3X plastic anchors
1X hex tool (90 degree wrench)
1X drill template
1X Ethernet weather housing
1X lens cleaning cloth
Safety instruction
Follow these instructions to ensure that the product is used
correctly and to avoid danger or property loss. Serious injury or
death may occur if any of the warnings are ignored. Injury or
equipment damage may occur if any of the cautions are
neglected.

2
WARNINGS
 In the use of the product, you must be in strict compliance
with the electrical safety regulations of the nation and
region.
 Refer to the technical specifications for detailed
information.
 Input voltage should meet both the SELV (Safety Extra
Low Voltage) and the Limited Power Source with 24 VAC
or 12 VDC according to the IEC60950-1 standard. Refer
to the technical specifications for detailed information.
 Do not connect several devices to one power adapter, as
adapter overload may cause over-heating or a fire hazard.
 Make sure that the plug is firmly connected to the power
socket.
 When the product is mounted on the wall or ceiling, the
device should be firmly fixed.
 If smoke, odor, or noise come from the device, turn off the
power at once and unplug the power cable. Contact the
service center.
 If the product does not work properly, contact your dealer
or the nearest service center. Never attempt to
disassemble the camera yourself. (We do not assume any
responsibility for problems caused by unauthorized repair
or maintenance.)

3
CAUTIONS
 Make sure the power supply voltage is correct before
using the camera.
 Do not drop the camera or subject it to physical shock.
 Do not touch the CMOS modules with your fingers. If
cleaning is necessary, use a clean cloth with a bit of
ethanol and wipe it gently.
 If the camera will not be used for an extended period,
replace the lens cap to protect the CMOS from dirt.
 Do not aim the camera at the sun or exceedingly bright
places. Blooming or smearing may occur (this is not a
malfunction), and affect the endurance of the CMOS at
the same time.
 The CMOS may be burned out by laser beams. When
using laser equipment make sure that the surface of the
CMOS is not exposed to the laser.
 Do not expose the camera to high electromagnetic
radiation, extremely hot or cold environments (the
operating temperature should be -30 to +60℃), or
dusty/damp locations.
 To avoid heat accumulation, ventilation is required for the
operating environment.
 Keep the camera away from liquid while in use.
 When returning a camera, pack it in its original packing, or
similar packing materials.
 Improper use or replacement of the battery may result in
explosion. Replace it with the same or equivalent type
only. Dispose of used batteries according to the
instructions provided by the battery manufacturer.

4
Overview
Figure 1: Camera overview
(1) Mounting base
(2) Horizontal stand
(3) Vertical stand
(4) Dome
(5) Cables
(6) IR LED
(7) Lens
(8) Black liner
(9) Safety rope
1
2
3
4
5
6
7
8
9

5
Installation
To ensure the camera operates properly, install the camera
according to the instructions below.
Before you start
 Make sure that the device in the package is in good
condition and all the assembly parts are included.
 Make sure that all related equipment is powered off during
installation.
 To determine the proper environmental operating
conditions, refer to Specifications on page 17.
 Make sure the power supply matches the required voltage
to avoid damage.
 If the product does not function properly, contact your
dealer or the nearest service center. Do not disassemble
the camera for repair or maintenance by yourself.
 Make sure that the wall is strong enough to withstand
three times the weight of the camera.

6
To mount the camera to the ceiling:
1. Drill the cable hole and the screw holes in the ceiling
according to the supplied drilling template.
Screw Hole
Screw Hole Screw Hole
Ceiling Mounting

7
2. Loosen the set screws with a hex tool (supplied) to
remove the dome.
3. Connect the corresponding cables.
Note: If required, you can route cables through the
opening on the side of the mounting base.
Side Opening

8
4. Fix the mounting base to the ceiling with screws.
5. Adjust the surveillance angle.
a. Loosen the tilt adjusting screws, and adjust the tilt
angle [0 to 65], and tighten the tilt adjusting screws.
b. Hold the black liner and rotate it to adjust the pan
position [0 to 360].
c. Remove the black liner and rotate the camera to
adjust the azimuth angle [0 to 360].
Tilt Adjusting Screw

9
Note: The lens has been factory adjusted to provide the
best imaging effect. You must adjust the pan and tilt
position to achieve the desired surveillance angle.
6. Reattach the dome and tighten the screws.
Setting the network camera
over LAN
To view and configure the camera via LAN (Local Area
Network), you will need to connect the network camera in the
same subnet as your PC. Then install the SADP software to
search for and change the IP address of the network camera.
The following figure shows the cable connection of a network
camera and a PC.

10
Figure 2: Wiring over LAN
To set the IP address of the camera to access via LAN:
1. To get the IP address, use the SADP software. It
automatically detects the network camera in the LAN. It
also displays the device’s information such as IP address,
subnet mask, port number, device serial number, and
device version. See the figure below.
2. Change the IP address and subnet mask to match subnet
of your PC.
After launching the SADP software, it automatically
searches your computers subnet for online devices every
15 seconds from. It displays the total number and
information of the found devices in the Online Devices
interface. The interface displays the device type, IP
address, port number, and gateway.

11
Notes
 The camera takes 15 seconds to show up online, and
45 seconds to show offline when it is removed.
 Click Refresh Every 15s to refresh the online device
list manually.
 Click or on each column heading to change
the order of the displayed information.
 Click to show the device table and hide the network
parameter panel, or click to show the network
parameter panel.

12
To modify device information:
1. Select the device from the device list, as shown below.
2. The network parameters of the device are displayed in the
Modify Network Parameters panel, as shown below.
3. Edit the network parameters as necessary.

13
4. Enter the password of the device’s admin account in the
Password field, and then click Save.
5. Enter the network camera’s IP address in the web
browser’s address field to view the live video.
Notes
 The default user name is “clareadmin,” and password is
“secure7.”
 Set the gateway for the network camera after you log in
when accessing the network camera from different
subnets.

14
Accessing via web browser
System requirement
 Operating system: Microsoft Windows XP SP1 and above
version / Vista / Win7 / Server 2003 / Server 2008 32 bits
 CPU: Intel Pentium IV 3.0 GHz or higher
 RAM: 1 G or higher
 Display: 1024 × 768 resolution or higher
 Web browser: Internet Explorer 8.0 and above; Apple
Safari 5.02 and above; and Mozilla Firefox 5.0 and above.
To access the camera via the web browser:
1. Open the web browser.
2. Enter the IP address of the network camera in the
browser’s address bar.
3. Enter the user name and password, and then click Login.
4. Install the plug-in as prompted to view the live video and
manage the camera.