Clare Controls CV-M3D10-ODI User manual

Doc ID - 339 • REV 04
Network Camera
Installation Guide
3 MP Mainline Dome Camera
Model CV-M3D10-ODI
Last modified: 09/29/16

2

Copyright
© 29SEP16 Clare Controls. All rights reserved.
This document may not be copied in whole or in part or
otherwise reproduced without prior written consent from
Clare Controls, LLC., except where specifically permitted
under US and international copyright law.
Trademarks and
patents
The 3 MP Mainline Dome Camera name is a trademark of
Clare Controls, LLC.
Other trade names used in this document may be
trademarks or registered trademarks of the manufacturers
or vendors of the respective products.
Manufacturer
Clare Controls, LLC.
7519 Pennsylvania Ave., Suite 104, Sarasota, FL 34243,
USA

i
Content
Description...1
Package contents...1
Safety instruction...2
Overview...4
Wiring...5
Installation...6
Before you start...6
Disassembling...7
Mounting...8
Conduit installation on the side...12
Ceiling mounting with gang box...14
Wall mounting...16
Image and focus adjusting...20
Setting the network camera over LAN...23
Accessing via a web browser...27
System requirements...27
Specifications...31
Regulatory information...33
Warranty information...35
Contact information...35

1
Description
The 3 MP Mainline Dome Camera is a high resolution fixed
dome IP camera with 3 MP, making it an appropriate choice for
outdoor applications where image detail and/or a wider
coverage is important. Capable of 2048 × 1536 resolution, the
camera incorporates digital wide dynamic range and 20 meter
IR LEDs for use in varying light conditions. The PoE Dome
Camera pans (0-355 degrees) and tilts (0-80 degrees), includes
a micro SD slot for up to 32 GB local memory, and is encased
in a vandal-resistant housing.
Package contents
1X metal mount ring
3X anchor screws
3X plastic anchors
1X ceiling mount template sticker
1X hex tool (90 degree wrench)
1X composite video output pigtail adapter (black wire with BNC
connector)
1X Ethernet weather housing
3X metric screws
1X 12 VDC power supply

2
Safety instruction
Follow these instructions to ensure that the product is used
correctly and to avoid danger or property loss. Serious injury or
death may occur if any of the warnings are ignored. Injury or
equipment damage may occur if any of the cautions are
neglected.
WARNINGS
 In the use of the product, you must be in strict compliance
with the electrical safety regulations of the nation and region.
 Refer to the technical specifications for detailed information.
 Input voltage should meet both the SELV (Safety Extra Low
Voltage) and the Limited Power Source with 24 VAC or
12 VDC according to the IEC60950-1 standard. Refer to the
technical specifications for detailed information.
 Do not connect several devices to one power adapter as
adapter overload may cause over-heating or a fire hazard.
 Make sure that the plug is firmly connected to the power
socket.
 When the product is mounted on the wall or ceiling, the
device should be firmly fixed.
 If smoke, odor, or noise rise from the device, turn off the
power at once and unplug the power cable. Contact the
service center.
 If the product does not work properly, contact your dealer or
the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not assume any responsibility for
problems caused by unauthorized repair or maintenance.)

3
CAUTIONS
 Make sure the power supply voltage is correct before using
the camera.
 Do not drop the camera or subject it to physical shock.
 Do not touch CMOS modules with fingers. If cleaning is
necessary, use a clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period,
replace the lens cap to protect the CMOS from dirt.
 Do not aim the camera at the sun or exceedingly bright
places. Blooming or smearing may occur (which is not a
malfunction), and affect the endurance of CMOS at the same
time.
 The CMOS may be burned out by a laser beam, so when
laser equipment is in use, make sure that the surface of
CMOS will not be exposed to the laser beam.
 Do not expose the camera to high electromagnetic radiation,
extremely hot or cold environments (the operating
temperature should be -30 to +60℃), or dusty or damp
locations.
 To avoid heat accumulation, good ventilation is required for
operating environment.
 Keep the camera away from liquid while in use.
 When returning a camera, pack it in its original packing, or
similar packing materials.
 Improper use or replacement of the battery may result in
hazard of explosion. Replace it with the same or equivalent
type only. Dispose of used batteries according to the
instructions provided by the battery manufacturer.

4
Overview
Figure 1: Camera overview
(1) Lower dome
(2) Black liner
(3) Reset button
(4) AUX video output interface
(5) Serial port
(6) Power interface
(7) Ethernet interface
(8) Mounting base
(9) Lens
Note: To reset the default parameters to the camera, press and
hold the reset button and power on the camera. After powered
on, continue to press and hold the reset button for another 10
seconds.
The dome camera supports audio and alarm functions. The
interfaces are shown in Figure 2.
1
45
2
3
67
8
9

5
Figure 2: Audio and alarm interfaces
Wiring
Wire your dome camera, as shown in Figure 3.
Figure 3: Wiring

6
Installation
To ensure the camera operates properly, install the camera
according to the instructions below.
Before you start
 Make sure that the device in the package is in good
condition and all the assembly parts are included.
 Make sure that all the related equipment is powered off
during the installation.
 To determine the proper environmental operating conditions,
refer to Specifications on page 31.
 Make sure the power supply matches the required voltage to
avoid damage.
 If the product does not function properly, contact your dealer
or the nearest service center. Do not disassemble the
camera for repair or maintenance by yourself.
 Make sure that the wall is strong enough to withstand three
times the weight of the camera.

7
Disassembling
To disassemble the camera:
1. Loosen the three screws on the edge of the lower dome
with a screwdriver.
2. Open the lower dome and remove the inner black liner, as
shown below.

8
Mounting
To mount on a ceiling:
1. Disassemble the camera as described in the previous
section.
2. Attach the drill template to the place where you want to fix
the camera.
3. As shown in the drill template below, drill three screw
holes in the ceiling.

9
4. If you want to route the cables inside the ceiling, drill a
cable hole in the ceiling according to the drill template.
Skip this step, if you want to route the cables on the
surface of the ceiling. Refer to Conduit installation on the
side on page 12.
5. Attach the camera to the ceiling by aligning the holes of
the back box with the holes on the ceiling.
6. Secure the camera with the supplied screws, as shown
below.

10
7. Route the cables through the cable hole.
8. Connect the video output connector to the monitor.
Connect the power connector to the power supply.
9. Adjust the image and focus.
10. Install the inner black liner back to the camera.

11
11. Install the lower dome back to the camera and secure it
with screws, as shown below.

12
Conduit installation on the side
If you want to route the cables from side of the camera, you
need to follow the steps below to install a conduit for cable
routing.
To route the cables from the side:
1. Rotate the waterproof plug counterclockwise to remove it
from the camera.
2. Remove the waterproof plug.
3. Route the power cable and network cable through the
side outlet to the conduit.
4. Align the conduit to the side outlet and rotate clockwise
until it is tight.

13
Note: For wall mounting, position the side outlet directly
downward for waterproofing.

14
Ceiling mounting with gang box
To mount the camera on the ceiling with a gang box:
1. Disassemble the camera.
2. Install the gang box in the ceiling.
3. Attach the mounting base to the gang box with two
screws.

15
4. Route the cables through the hole in the center of the
mounting base.
5. Align the camera with the mounting base.
6. Tighten the screws to secure the camera with the
mounting base.
7. Connect the video output connector to the monitor.
Connect the power connector to the power supply.
8. Adjust the image and focus.

16
9. Install the inner black liner back to the camera.
10. Align the lower dome with the camera.
11. Tighten the screws to secure the lower dome with the
camera, as shown below.
Wall mounting
For the wall mounting, you must purchase a wall mount.
To mount the camera on the wall:
1. Disassemble the camera.
2. Install the wall mount and mounting adapter, as shown
below.