Clare Controls Mainline 2MP User manual

Doc ID 2014-11-684 • REV 02
Network Camera
Installation Guide
Mainline 2MP PTZ Dome

i
Content
Description...1!
Safety instruction...1!
Overview...4!
Micro SD card instructions...5!
Installation...5!
Wall mounting...6!
In-ceiling mounting...10!
Setting the dome over the LAN...15!
Accessing via a web browser...20!
System requirements...20!
Specifications...24!
Regulatory information...27!
Contact information...29!

ii

1
Description
The ClareVision Mainline 2MP PTZ Dome camera
(CV-M2PT10-OD) is integrated with a built-in pan/tilt unit and
a digital image receiver. The camera features highly sensitive
response and reliable performance, and it also ensures the
image clarity and stability.
Safety instruction
Follow these instructions to ensure that the product is used
correctly and to avoid danger or property loss. Serious injury
or death may occur if any of the warnings are ignored. Injury
or equipment damage may occur if any of the cautions are
neglected.
WARNINGS
•In the use of the product, you must be in strict compliance
with the electrical safety regulations of the nation and
region.
•Please refer to technical specifications for detailed
information.
•Input voltage should meet both the SELV (Safety Extra
Low Voltage) and the Limited Power Source with 24 VAC
or 12 VDC according to the IEC60950-1 standard. Please
refer to technical specifications for detailed information.
•Do not connect several devices to one power adapter as
adapter overload may cause over-heating or a fire hazard.
•Please make sure that the plug is firmly connected to the
power socket.
•When the product is mounted on wall or ceiling, the device
should be firmly fixed.

2
•If smoke, odor, or noise rise from the device, turn off the
power at once and unplug the power cable. Contact the
service center.
•If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (We shall not assume
any responsibility for problems caused by unauthorized
repair or maintenance.)

3
CAUTIONS
•Make sure the power supply voltage is correct before using
the camera.
•Do not drop the camera or subject it to physical shock.
•Do not touch CMOS modules with fingers. If cleaning is
necessary, use a clean cloth with a bit of ethanol and wipe
it gently. If the camera will not be used for an extended
period, replace the lens cap to protect the CMOS from dirt.
•Do not aim the camera at the sun or extra bright places.
Blooming or smearing may occur (which is not a
malfunction), and affect the endurance of CMOS at the
same time.
•The CMOS may be burned out by a laser beam, so when
any laser equipment is in use, make sure that the surface
of CMOS will not be exposed to the laser beam.
•Do not place the camera in extremely hot or cold
environments (the operating temperature should be
-30°C to +60°C), dusty or damp locations, and do not
expose it to high electromagnetic radiation.
•To avoid heat accumulation, good ventilation is required for
the operating environment.
•Keep the camera away from liquid while in use.
•When returning a camera, pack it in its original packing, or
similar packing materials.
•Regular part replacement: a few parts of the equipment
should be replaced regularly according to their average
enduring time. The average time varies because of
differences between operating environment and use history,
so regular checking is recommended for all users. Contact
your dealer for more details.

4
•Improper use or replacement of the battery may result in
hazard of explosion. Replace it with the same or equivalent
type only. Dispose of used batteries according to the
instructions provided by the battery manufacturer.
•If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
disassemble the camera yourself. We do not assume any
responsibility for problems caused by unauthorized repair
or maintenance.
Overview
Figure 1: Mainline 2 MP PTZ Dome camera
(1) Power cables
(2) Audio cables
(3) Network cable
V
4
2
C
A
D
E
R
N
E
E
R
G
/
W
O
L
L
E
Y
V
4
2
C
A
K
C
A
L
B
1
2
3

5
Micro SD card instructions
There are two kinds of SD card slot positions because of
different dome models. Refer to the following reference-only
figures.
Figure 2: Install the SD card
Installation
Before you start, check the package contents and make sure
that the device in the package is in good condition and that all
the assembly parts are included.
Notes
•Do not remove the protective film from the lower dome until
after the installation is complete.
•Do not touch the bubble of the lower dome directly by hand.
The image blurs otherwise.
•Do not carry the camera by its waterproof cables (see
Figure 3), as this may affect its waterproof performance.
SD Card Slot
SD Card Slot

6
Figure 3: Do not carry the dome by its cables
Wall mounting
When mounting the dome to a wall, be sure that the wall is
thick enough to mount the expansion screws. The wall must
be strong enough to withstand more than four times the weight
of the dome and its accessories.
To mount the dome to a wall:
1. Drill screw holes as shown below.
a. Attach the wall mount to the wall where you need to
install the dome.
b. Drill four screw holes according to the screw holes on
the wall mount.
c. Hammer four M8 expansion pipes (not supplied) into
the screw holes.

7
2. Loosen the screws and remove the lower dome from the
back box.
3. Remove the protective lens cover, foam, and sticker
from the dome drive. See the following figure.
4. Attach the lower dome to the back box, and then secure
it with screws.
Screw holes

8
5. Secure the dome to the wall mount.
a. Feed the dome cables through the wall mount.
b. Rotate the connector of dome to the wall mount.
c. Tighten the lock screw with the hex key (supplied) to
secure the two units.
Lens cover
Protective sticker
Protective foam

9
6. Route the cables and secure the wall mount.
a. Route the cables for the dome. Refer to “Overview”
for connecting the cables.
b. Tighten the set screws to secure the wall mount to
the wall with the dome.
VI EOD
VI EOD
Cables
Connector
Lock screw

10
In-ceiling mounting
When mounting the dome in the ceiling, be sure that the
height of the space above the ceiling is more than 25 cm. The
ceiling must be with the thickness between .5 and 4.0 cm. The
ceiling must be strong enough to withstand more than four
times the weight of the dome and its accessories.
To mount the dome to a ceiling:
1. Drill holes in the ceiling.
a. Attach the drill template to the ceiling where you need
to install the dome.
b. Cut a hole and drill screw holes according to the drill
template.
Note: ±2 mm of the diameter of the circle is tolerable.
Set screws

11
2. Disassemble the dome.
a. Loosen three screws as shown in the following figure.
b. Remove the lower dome.
3. Loosen the three screws and remove the back box.
Three screws
Lower dome

12
4. Remove the protective lens cover, foam, and sticker
from the dome drive.
5. Install the toggle bolts.
a. Remove the toggle from the toggle bolt.
b. Insert the bolts into the screw holes on the dome.
c. Rotate the bolts through the screw holes.

13
6. Reinstall the toggles as shown below.
7. Align the toggle bolts with the screw holes on the ceiling.
Toggle bolt holes
Toggle
Bolt

14
8. Push the dome to the mounting hole on the ceiling.
9. Rotate the bolts again. The toggle will automatically
rotate down to secure the dome to the ceiling.
10. Attach the lower dome to the dome.
11. Secure the lower dome with three screws.
12. Route the cables through the ceiling for the dome. Refer
to “Overview” for connecting the cables.
Toggle
Ceiling
Screws

15
Setting the dome over the LAN
To view and configure the camera via a Local Area Network
(LAN), you will need to connect the network camera in the
same subnet as your PC. Next, install the SADP software to
search and change the IP of network camera. You can
download the SADP software tool from the Clare Controls
website at www.clarecontrols.com.
The following figure shows the cable connection of network
camera and PC.

16
Figure 4: Wiring over LAN
To set the camera’s IP address for accessing via LAN:
1. To get the IP address, use the SADP software tool. The
tool can automatically detect the network camera in the
LAN and list the device information, such as IP address,
subnet mask, port number, device serial number, device
version, etc., shown in the following figure.