clare CLR-C1-ODDG Assembly instructions

© 18AUG20 Clare Controls, LLC. 1 / 4 DOC ID – 1947 • Rev 03
ClareOne Outdoor Sensor Installation Sheet
Last modified: 08/18/20
Model number: CLR-C1-ODDG
Description
The CLR-C1-ODDG is a supervised wireless sensor that
detects the opening and closing of doors, windows, gates,
garage doors, etc. in extreme environments (-32° to 120°F
(-35.6° to 49°C)). The sensor is constructed with a water-tight
internal gasket to keep the sensor dry and protected from the
elements. The unique design allows for outdoor mounting. The
sensor and magnet are mounted using screws (included) or
straps to secure the sensor to a post.
When activated, the sensor transmits an open (trip) or close
(restore) signal to the panel. The sensor transmits supervisory,
tamper, and low battery (as needed) to the ClareOne panel.
The sensor is powered by (2) replaceable CR 2032, 3-VDC,
Lithium batteries.
Installation
Follow the installation guidelines.
•Mount the sensor on a non-moving frame or post, allowing
the magnet to move activating the sensor.
•Mount sensors at least 5 inches above the ground to avoid
damaging them.
•The sensors can be mounted to either wood or metallic
surfaces.
•Mounting the sensor on metal can affect the transmitting
range and magnet gap performance. Test the sensor from
the desired location using the installer sensor test before
permanently mounting. (This test can be performed using
the ClareOne panel’s sensors testing feature. Settings >
User/Installer Settings > System Tests > Sensor Test)
•The magnet should be mounted within 7/8” for wood or
1/2” for metal installations. Based on the magnet mount
spacing, direction of operation, and material of the
mounting surface, the gap for opening varies between 1/8”
and 1 ¾”. Desired operation should be checked before
permanent installation.
•After mounting the sensor, re-test the sensor using the
procedure in the section “Testing the sensor.”
Mounting the sensor
Mount the sensor using the supplied mounting screws or
straps (not included).
To mount the sensor using mounting screws:
1. Remove the cover screw from the sensor.
2. Mount the sensor using 3 mounting screws and the
magnet using 2.
3. Mount the magnet into the desired location making sure
the magnet alignment mark lines up with the sensor mark.

2 / 4 DOC ID – 1947 • Rev 03
To mount the sensor using mounting straps:
Note: The sensor case is designed to support strap mounting.
1. Use a plastic tie strap and wrap it around the mounting
post and through the sensor.
Notes
•Make sure the straps are tight, preventing the sensor
from sliding away from the magnet.
•We recommend not using metal tie strips. They may
interfere with RF signals.
2. Mount the magnet by running a strap through the slot in
the magnet housing.
Note: Make sure straps are tight to prevent the sensor
from sliding away from the magnet.
External contact
An external contact can be connected to the transmitter or
other device by feeding contact wiring through the rubber
grommet.
Notes
•Do not exceed 50 ft. when wiring to an external contact.
•Only one set of contacts can be used at one time. Either
use the external contact input or use the provided
magnetic contact. They cannot be used together. To
prevent physical bypass of the external contact, cut the
internal reed switch.
Programming
To add the sensor to your panel and for detailed programming
instructions, please refer to the ClareOne Wireless Security
and Smart Home Panel User Manual (DOC ID 1871).
To add the door window sensor:
1. Put the ClareOne panel in “add mode” and follow the
displayed instructions for adding the sensor.
2. Pull the magnet away from the sensor body.
– Or –
Open the sensor body case to tamper.
3. Exit “add mode.”
Testing the sensor
Test the sensor once a week.
To test the sensor:
1. Set the panel to the sensor test mode. See the full
ClareOne Panel manual.
2. Take the sensor and magnet to the desired mounting
location, making sure to line up their alignment marks with
each other. Trip the sensor by pulling the magnet away
from the sensor, or by opening/closing the attached
external contact.
3. Monitor the system after tripping the sensor.
Note: If a low battery alarm occurs, replace the battery within 7
days.
CAUTION: Battery may explode if mistreated. Do not recharge,
disassemble or dispose of in fire.
Specifications
Compatible panel
ClareOne (CLR-C1-PNL1)
Transmitter frequency
433MHz
Encrypted
Yes
Operating
gap 1.75” (44 mm)
Transmitted indications
Alarm, supervision, tamper and low battery
Dual tamper; sensor and case added for
security.
Supervisory keep
-alive 60 to 70 minutes
Battery type
(2x) CR2032
Battery life
6 to 8 years
Operating environment
Temperature
Relative humidity
-35 to 120°F (-37 to 49°C)
0 to 95% noncondensing

DOC ID - 1947 • Rev 03 3 / 4
Dimensions
(
L × W × H)
Sensor
3.39” L × 1.34” W × 0.7” H.
(86.1 ×34.03 × 17.78 mm)
Magnet
1” L × 7/8” W × 0.7” H.
(25.4 ×22.23 × 17.78 mm)
Water r
esistant Yes
Certifications
FCC: 15.109 Class B 15.231, Industry
Canada: ICES-003, RSS-210
Regulatory information
Manufacturer
Clare Controls, Llc.
7519 Pennsylvania Ave, Suite 104
Sarasota, FL 34243
FCC compliance
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation.
If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment
and receiver.
• Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
This device complies with Industry Canada
license-exempt RSS standard(s). Ope
ration
is subject to the following two conditions: (1)
this device may not cause interference, and
(2) this device must accept any
interference, including interference that may
cause undesired operation of the device.
Cet appareil est conforme avec Industrie
Canada exempts de licence standard RSS
(s). Son fonctionnement est soumis aux
deux conditions suivantes: (1) cet appareil
ne doit pas provoquer d'interférences et (2)
cet appareil doit accepter toute interférence,
y compris celles pouvant causer un
mauvais fonctionnement de l'appareil.
In accordance with FCC requirements of
human exposure to radio frequency fields,
the radiating element shall be installed such
that a minimum separation distance of 20
cm is maintained from the general
population.
FCC: 2ABBZ-RF-DWSOD-433
IC: 11817A-RFDWSOD433
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and (2)
this device must accept any interference
received, including interference that may
cause undesired operation. Changes or
modifications not expressly approved by the
party responsible for compliance could void
the user's authority to operate the
equipment.
This Class B digital apparatus complies with
Canadian ICES-3B.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
MANUFACTURER HEREBY DISCLAIMS
ALL WARRANTIES AND
REPRESENTATIONS, WHETHER
EXPRESS, IMPLIED, STATUTORY OR
OTHERWISE INCLUDING (BUT NOT
LIMITED TO) ANY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE WITH RESPECT
TO THESE PRODUCTS AND ANY
RELATED SOFTWARE.
MANUFACTURER FURTHER DISCLAIMS
ANY OTHER IMPLIED WARRANTY
UNDER THE UNIFORM COMPUTER
INFORMATION TRANSACTIONS ACT OR
SIMILAR LAW AS ENACTED BY ANY
STATE.
(USA only) SOME STATES DO NOT
ALLOW THE EXCLUSION OF IMPLIED
WARRANTIES, SO THE ABOVE
EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS AND YOU MAY ALSO
HAVE OTHER LEGAL RIGHTS THAT
VARY FROM STATE TO STATE.
MANUFACTURER MAKES NO
REPRESENTATION, WARRANTY,
COVENANT OR PROMISE THAT ITS
ALARM PRODUCTS AND/OR RELATED
SOFTWARE (I) WILL NOT BE HACKED,
COMPROMISED AND/OR
CIRCUMVENTED; (II) WILL PREVENT, OR
PROVIDE ADEQUATE WARNING OR
PROTECTION FROM, BREAK-INS,
BURGLARY, ROBBERY, FIRE; OR (III)
WILL WORK PROPERLY IN ALL
Environmental
class
UL: Indoor dry
IEC: 3K5

4 / 4 DOC ID – 1947 • Rev 03
EU compliance
EN 54
EN 54-00:0000
European Union
directives
1999/5/EC (R&TTE directive): Hereby, Clare
Controls declares that this device is in
compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC.
2002/96/EC (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the
European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific
battery information. The battery is marked with
this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to
your supplier or to a designated collection point.
For more information see: www.recyclethis.info.
Warranty information
Clare Controls offers a two (2) year limited warranty on original
Clare Controls components, from the date of shipment from
Clare Controls.
Contact information
Clare Controls, LLC.
7519 Pennsylvania Ave, Suite 104
Sarasota, FL 34243
General: 941.328.3991
Fax: [phone]
www.clarecontrols.com
Integrator/Dealer Support: 941.404.1072
[e-mail]
Homeowner Support (ClareCare): 941.315.2273 (CARE)
[e-mail]