Clarion CMRC1-BSS Troubleshooting guide

Clarion'
CMRC1-BSS
CMRC1-SB
MARINE REMOTE-MOUNTED CONTRQ~PJ\N~L
Owner's Manual/Installation Guide

l:j

1. Intr4oduction··········,·····~·,· .... ·· .. ·········,·HRf~~~~c~~
2. Care and Maintenance.. ~., "., ...• J.:LH..tUiB,WJlUm:
3. Using the Remote Contr'oIIPalraeIU ••• c~c~~~c~.'.".~;~.~~.~.~cW~
4. Installation and

The [SELECT UP/DOWN] buttons:
In CD modes (single-disc and CD
serve two functions:
Track navigation:
~elect the next track on the disc, press
and release the
~ button.
To return to the beginning of
lease the E) button.
To "back up" afew tracks, press andrelease the
repeatedly until the desired track number is displayed.
-"';:£l!::llI"t:'I/'\,,-
ing within atrack: To fast-forward or ~-reverse
track, press and hold the 8or ~ button.
In optional Sirius Satellite Radio mode: These buttons
select the next preset radio station in the "
c· '.••. ·. ,.:. ;,>
press preset radio station in the memory.

Before you begin installation of the rern
verify that you have sufficient
clearanceint
tion. Note that 2.5 inches of mounting dept
rnounting surface) is required to avoid ca
surface is required
in order to ensure a
installation is complete.
Before cutting any panel, A
ensurethat there
is sufficie
ance behind the panel, a
wire harnesses, fuel lin
linkages,
or any other c
ponents are exposed t
your choice of locatio
damage
to the hull whi
opening.
'::-e the boat for installation by ca
anels as necessary. Route .
edges, and ensure that no
reed during reassernbly.

4.
Insert
the
remote control panel
into
that the gasket
behind
the remote
completely
against the mounting surface.
5.
Position the bracket onto the rear
of
the remote control pariel,
sliding the two threadedstuds on
the
rearotthepanel
through
the two holes in the mounting
bracket{as
shownbel0-.v)
.1"i~ht"
en the 7mm hex nuts onto the bracket,
again
ensuring
that
the
gasket seals tightly to the front of the mounting surface.
AvOii:!
pinching the cable.
Mounting Bracket
JI~!!lr~II~~~~\~!~'~I~~!"~8,untirn.~kl~alion
is
aflat
surface
with
suf-
~TfC:!lnp~
t;~~;"'Jcma
access. Ensure that
the
~~ll~ei$u,bd«:!~SlfUIIY
completed before con-
v,
.,,"""""'"
a24' extension is
1
!10!flllll~~I!ii!:lilll~1!~E~~~~~with
"break lines'
to
allow
thi{'knIA~<::~Ac:.
Determine
if
the
and remove the appropriate
apair of pliers. Each

Connect awire to one of
the mounting studs
on the
rear of the unit, using a#8
ring terminal (not supplied).
Connect this wire to the
boat's negative (-) ground.
Wiring Connections
•Disconnect the negative battery terminal before making any
wiring connections.
•Be particularly careful where you route wires and cables.Keepthe:rn,
away from the engine, exhaust system, etc, Heat may damage wires.
•Sharp edges can pierce wire insulation and cablejackets,
cau$il'1g
short circuits, damage to the craft, blown fuses, and system failure.
If any fuse should blow, make sure all connections are correct and
no wires are damaged before replacing the fuse. Always use fuses
that are the same amperage value
astheoriginal.Wh~nreplacing
afuse, never let the battery side touch any
metal part or any other wire.
Wiring
1. Connecting the ground lead.
ote control
rear
of the
bracket (as
bracket
htly to the
cable.
~W~i1
>
"
of the rem
Sl' JS on the
.",'
It:::, IIIVUllLlIl~
nuts into
f ........ ''"' seals tig
'.',., th
III VlllvUIII~ e
,;"
'" ..
'; '"
"
;.i
,',.'. ;",
,;,
;'.
III
.
tl
,';
;
•
".
~-
-
ii, ..
J:. ,." "-
"'"
s
"'"
';
.......
"
....... ~
.'
,
e.,'
", '.,

3. Connecting the cables.
Connect
the
DIN cable
fro,nm~;t~h:~e~~i~l:J6~8r~~I\1
to the
rerno1:e(~;).
c
CMD4
or
M455

6. Product must be shipped in it
fully insured, with shipping
any responsibility for any I
7. ALL IMPLIED WARRANTI
ITED BYAPPLICABLE L
TION THAN THE WARRA
UNDER NO CIRCUMSTAN
ANY LOSS OR DAMAGE,
ING
OUT OF THE USE OR
BECAUSE SOME STATES
HOW LONG AN IMPLIED
OR LIMITATIONS
OF INCI
AGES, THE ABOVE LIMI
APPLY TO YOU.
8. THIS LIMITED WARRANT
RIGHTS, AND YOU MAYA
VARY FROM STATE TO
9. Should you have any diffic
during the warranty period,
clarion.com) for alistin
your area. You may als
In USA:
Clarion Corporation
of
Attn: Customer Service
661 W. Redondo Beac
Gardena, CA. 902
1-800-GO-
(310) 327-910
www.c1arion.co

CIRRC'-SB
WATERTIGHT MARINE
DISPLAY REMOTE CONTROL
~ Meets ASTM B117 Salt/Fog Exposure Standard
~ Meets ASTM 04329 UV Exposure Standard
~ Ignition Protection Certified
~ High Definition Positive LCD Display
~ Bright White LED Illumination
~ Rubber Tactile Action Control Buttons
~ Multi-Remote Compatible
~ Compatible with Clarion Marine CMD4, M455,
and XMD3 Source Units