Clarke ODC8 User manual

OIL DRAIN CART
OIL DRAIN CART
MODEL No: ODC8
Part No: 3051470
ASSEMBLY and OPERATING
INSTRUCTIONS
0107
ASSEMBLY DIAGRAM
No: Description Part No:
1 Grille CTODC801
2 Handle Grip CTODC802
3 Handle CTODC803
4 Reservoir CTODC804
5 Nut CTODC805
6 Washer CTODC806
7 Bolt CTODC807
8 Nut CTODC808
9 Washer CTODC809
10 Caster CTODC810
12 Valve CTODC812
13 Axle CTODC813
14 Bearing CTODC814
15 Wheel CTODC815
16 Coupler CTODC816
17 O-Ring CTODC817
No: Description Part No:
For Spare Parts and Service, please contact your nearest dealer,
or CLARKE International, on one of the following numbers.
PARTS & SERVICE TEL: [phone]
PARTS & SERVICE FAX: [phone]
or e-mail as follows:
PARTS: [e-mail]
SERVICE: [email protected]
PARTS & SERVICE CONTACTS

Thank you for purchasing this CLARKE Oil Drain Cart, which is designed to provide
a means of draining oil from all sizes of vehicle, quickly and cleanly, then
conveniently transporting that oil so that it may be transferred to a storage tank
either by gravity or by using a suction device.
Before using this Cart, please read this leaflet thoroughly and follow the instructions
carefully. In doing so you will ensure the safety of yourself and that of others around
you, and you can look forward to the Drain Cart giving you long and satisfactory
service.
GUARANTEE
This CLARKE product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt as proof of purchase.
This guarantee is invalid if the product is found to have been abused or tampered
with in any way, or not used for the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product can be
returned to us without prior permission.
This guarantee does not effect your statutory rights.
SAFETY PRECAUTIONS
• Check to ensure the unit is in perfect condition before use - no cracks etc.,
which would result in oil leakage.
• When disposing of oil, it must be disposed of according to law. NEVER pour
down drains etc.
• Ensure the vehicles’ engine is switched OFF and the vehicle is properly parked
before locating the unit beneath the drain point.
• Ensure the unit is stable before opening an oil drain.
• Be aware that the oil to be drained can be very hot. Take precautions to
avoid being burned.
• Should oil be spilled, the area must be cleaned completely and sand or
sawdust etc., scattered on the area, with a notice to alert people in the vicinity
to the possible danger of slipping.
• ALWAYS ensure the Grille is in place as this helps to prevent splashing and to
avoid spillage when transporting oil.
ASSEMBLY
Unpack the carton and check to ensure that no item was damaged during transit.
Should any damage be apparent, please contact your Clarke dealer immediately.
1. Referring to the Assembly Drawing on the back page, attach the handle
(#3) by fitting it inside the bracket between the two caster brackets. Secure
it with a bolt (#7), washer (#6) and nut (#5).
2. Fit the Casters (#10), one to each bracket either side of the handle. Slide
the caster’s threaded shaft through the hole in the bracket, from beneath,
and secure with a washer (#9) and nut (#8).
3. Attach the wheels (#15) to the axle brackets at the rear of the unit. Slide the axle
through the bracket and secure using a washer (#9) and nut (#8). Tighten securely.
4. Before threading the valve (#12) on to the threaded spigot on the rear of the
cart, wrap PTFE thread tape (not included), clockwise around the spigot thread.
5. Screw the coupler (#16) with O-Ring (#15) into the threaded outlet, and tighten.
Thread on the valve so that the valve lever faces upwards.
Your Oil Drain Cart is now ready for use.
METHOD OF USE
Ensuring the vehicle is properly parked, slide the cart beneath the drain point.
Ensure the drain valve lever is at right angles the valve - i.e. in the OFF position.
Remove the vehicles’ oil drain plug
and allow oil to flow into the cart -
take necessary precautions to avoid
spillage and the effects of hot oil.
When complete, replace the oil
drain plug and carefully withdraw
the cart from beneath the vehicle.
To drain oil from the cart, either gravity
or suction device may be used.
Simply roll the cart directly over an
approved oil tank ensuring the oil
drain sits directly over the opening in
the tank. Open the carts’ drain valve
and allow the oil to drain into the tank.
A piece of hose may also be used on the end of the drain valve spigot if required.
Alternatively, if a suction pump is available, attach the inlet hose from the pump to the
coupler (#16) on the cart (an adapter may be required but is not provided), and the
outlet hose from the pump into the approved oil storage tank, then begin to pump either
by hand, or, if an electric pump is used, ensure it is set to its lowest speed.
Be aware that some sediment will remain in the bottom of the cart. This should be
cleaned out thoroughly before the cart is put away.