Clarke Devil 330 Installation and operation manual

OPERATING & MAINTENANCE
INSTRUCTIONS
Devil 330
Part Nos: 6920264 (110V) & 6920265 (230V)
GC0310
DEVIL CERAMIC SPACE
HEATERS

2
INTRODUCTION
Thank you for purchasing this CLARKE Ceramic Space Heater.
Please read this manual thoroughly and follow the instructions carefully.
Before attempting to use the heater, thoroughly familiarise yourself with the
heater & its operation. In doing so you will ensure the safety of yourself and
that of others around you, and you can look forward to the heater giving you
long and satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
ENVIRONMENTAL PROTECTION
Do not dispose of this product with general household waste. This
product contains valuable raw materials and must be disposed of
according to the laws governing Waste Electrical and Electronic
Equipment, at a recognised disposal facility.

3
GENERAL SAFETY RULES
1) WORK AREA
1. These heaters are for INDOOR USE ONLY.
2. Do not expose the heater or power cable to rain or wet conditions. Any
water entering the heater will increase the risk of electric shock. DO NOT
use this heater in a bathroom, shower room or any other wet environment.
3. NEVER locate the heater near combustible materials such as curtains,
furniture etc. Allow at least 2 metre distance.
4. DO NOT locate the heater close to an adjacent wall or low ceiling. Allow
a distance of at least 1 metre from a wall or ceiling. Avoid placing the
heater directly below power socket outlets.
5. Take care to ensure that the front guard cannot be covered.
6. Do not operate heater in explosive atmospheres such as in the presence
of flammable liquids, gases or dust such as in a paint spray booth or any
explosive environment.
7. Never stand the heater on a movable vehicle where it could tip over.
8. Do not allow the emitters to become covered with dust which could
become a fire hazard. If used in a dusty workplace it should be cleaned
as described under Cleaning and Maintenance.
9. NEVER touch the emitters for at least 15 minutes after switching off.
10. DO NOT leave the heater unattended.
11. If children are present always use with a fireguard.
12. Store the heater out of the reach of children and do not allow persons
unfamiliar with these instructions to operate it.
13. Do not use this heater with a programmable timer used to switch it on
automatically.
14. Use ONLY in an upright position.
2) ELECTRICAL SAFETY
1. Electrical appliances must match the power outlet. Never modify the plug
in any way. Do not use adaptor plugs with earthed (grounded)
appliances. Correct plugs and outlets will reduce the risk of electric shock.
2. Do not abuse the electrical cable. Never use the cable for pulling or
unplugging the heater. Keep the cable away from sources of heat, oil,
sharp edges or moving parts. Damaged or tangled cables increase the
risk of electric shock.
3. Keep the mains cable well away from machines and ensure an adequate
electrical supply is close at hand so that the operation is not restricted by
the length of the cable.

4
4. ALWAYS disconnect from the mains supply before moving the heater, or
performing any cleaning or maintenance tasks.
5. Inspect the mains cable regularly for signs of damage. DO NOT use if it is
damaged, and ALWAYS keep it away from the source of heat.
6. Check the heater for damage before use. Any damage should be
properly repaired or the part replaced. If in doubt, DO NOT use. Consult
your local Clarke dealer.
3) SERVICE & REPAIRS
1. If necessary, have your heater repaired by a qualified person using
identical replacement parts. This will ensure that the safety of the
appliance is maintained.
Additionally, please keep these instructions in a safe place for future
reference.
ELECTRICAL CONNECTIONS
230V HEATER
The 230v model (Clarke part no 6920265) is provided with a 13 amp BS 1363 plug,
fitted with a 13amp fuse and MUST be connected to a standard, 230 Volt (50Hz)
electrical supply, preferably through a suitably fused isolator switch.
WARNING: THIS APPLIANCE MUST BE EARTHED
IMPORTANT: The wires in the mains lead should be wired up in accordance
with the following colour code:
Green & Yellow - Earth
Blue - Neutral
Brown - Live
As the colours of the flexible cable of this appliance may not correspond with
the coloured markings identifying terminals in your plug, proceed as follows:
• Connect the GREEN & YELLOW coloured cord to the plug terminal
marked with a letter E or Earth symbol “ ” or coloured GREEN or
GREEN & YELLOW.
• Connect the BROWN coloured cord to the plug terminal marked a
letter “L” or coloured RED.
• Connect the BLUE coloured cord to the plug terminal marked a
letter “N” or coloured BLACK.

5
If this appliance is found to be fitted with a plug which is moulded on to the
electric cable (i.e. non-rewireable) please note:
1. The plug must be thrown away if it is cut from the electric cable. There is a
danger of electric shock if it is subsequently inserted into a socket outlet.
2. Never use the plug without the fuse cover fitted.
3. Should you wish to replace a detachable fuse carrier, ensure that the
correct replacement is used (as indicated by marking or colour code).
4. Replacement fuse covers can be obtained from your local Clarke dealer
or most electrical stockists.
FUSE RATING
The fuse in the plug must be replaced with one of the same rating and this
replacement must be ASTA approved to BS1362.
We strongly recommend that this machine is connected to the mains supply
via a Residual Current Device (RCD).
110V HEATER
The 110v model (Clarke part no 6920264) MUST be connected to a 110 Volt, 1
phase 50Hz supply through a suitably fused isolator switch. On no account
must a 230V, 13amp (BS1363) plug be used.
NOTE: If a portable 110V transformer is used, make sure it has a rated
capacity sufficient to take the load of the heater.
In the event that the heater is hard wired into the electrical system, it must be
carried out in accordance with IEE regulations.
The user should purchase a suitable connecting lead which is compatible
with the appliance socket. A length of 2-3 metres is recommended as giving
mobility to the heater but without becoming a trip hazard.
If in any doubt, consult a qualified electrician. DO NOT attempt any electrical
repairs yourself.

6
UNPACKING AND ASSEMBLY
Before assembling, please check contents against the following list and
advise your dealer immediately if any parts are missing.
1 x Heater
2 x Support Legs
4 x Screws
1. Attach the side legs to the
heater using the screws
provided.
2. Fit the feet and end caps as
shown.
3. DO NOT use the heater
without fitting the legs.
INSTRUCTIONS FOR USE
1. Place the heater on a firm, solid foundation, and following all safety
precautions, plug in to a suitable mains supply.
2. The power output can be adjusted at three settings.
HCTIWS
1
HCTIWS
2
TAEH
TUPTUO
NOFFOW008
FFONOW0061
NONOW0042
NOTE: The heater is equipped with a tip-over device that
automatically shuts the power off should the heater tip over.
If this happens, simply place the heater in its correct position
and it will immediately restart.

7
CLEANING & MAINTENANCE
ALWAYS allow the heater to cool down for at least 15 minutes and disconnect
from the mains supply before performing any maintenance tasks.
PERIODICALLY
• Inspect the mains cable for damage. Undue heat will cause the cable to
stiffen and crack. If this is found, have the cable replaced. Check cable
routing and ensure it is well away from the heat source.
• Disconnect from the mains supply, remove the guard and wipe the
reflector and elements with a clean damp cloth. DO NOT use abrasive
cleaners. Take care that no moisture enters the heater.
• Refer to your CLARKE dealer if internal maintenance is required.
• When storing the heater, allow it to cool down, then place it in its packing
box for storage in a dry, ventilated place.
CERAMIC ELEMENT REPLACMENT
Ceramic elements are long lasting and should not need replacing under
normal circumstances. Should this become necessary take the heater to your
Clarke dealer.
For parts & Servicing, please contact your nearest dealer, or
CLARKE International, on one of the following numbers.
PARTS & SERVICE TEL: [phone]
PARTS & SERVICE FAX: [phone]
or e-mail as follows:
PARTS: [email protected]
SERVICE: [email protected]

8
melborP esuaCelbissoP ydemeR
tonseodretaeH
hguohtla,etarepo
dnanideggulp
.nodehctiws
dab/esoolsigulP
.noitcennoc
ehtkcehc&tuogulpehtlluP
dnagulpehtfonoitcennoc
.tekcos
nwolbesuFdnayrassecenfiecalpeR
swolbesuffI.esuacetagitsevni
EKRALCruo
ytlusnoc,yldetaeper
.relaed
tekcostarewopoN
.teltuo
elbatiusanigulpehttresnI
.tekcos
tnemelegnitaeH
.tohgniw
olg
hgihootegatlovtupnI
.wolootro
niylppusrewopaesU
gnitarehthtiwecnadrocca
.lebalehtno
yltrapsitelniriA
.de
kcolb
yawatpeksiretaehehterusnE
slairetamrostcejboynamorf
ehtrevocyllaitrapdluochcihw
.tiotninwardebrodraugtnorf
FAULT FINDING

9
COMPONENT PARTS
oN noitpircseD oNtraP oN noitpircseD oNtraP
1drauGtnorF71004202XA31elbaC52109302XA
2wercS97003202XA41elbaC62109302XA
3lenaPtnorF58903602XA51elbaC72109302XA
4t
nemelEgnitaeH61007002XA61tooFrebbuR71002002XA
5lenaProtcelfeRediS32003602XA71rehsaW84103202XA
6lenaProtcelfeRniaM2
2003602XA81wercS67003202XA
7teviR19103202XA91tooF42001602XA
8eldnaH70001002XA02hctiwSFFO/NO41002302XA
9lenaPraeR0990360
2XA12pmalCelbaC11001302XA
11hctiwSrevo-piT71002302XA22elbaCrewoP60409302XA
21troppuShctiwS70202602XA

10
TECHNICAL SPECIFICATION
Please note that the details and specifications contained herein, are correct
at the time of going to print. However, CLARKE International reserve the right
to change specifications at any time without prior notice.
A selection of suitable extension leads & plugs is available from your nearest
CLARKE dealer, for further information, contact your nearest dealer, or
telephone CLARKE International Sales department on 01992 565300.
ledoM 033liveD
oNtraP46202965620296
thgieWgk6gk6
mm)HxWxL(snoisnemiD525x004x563525x004x563
tuptuOtaeH.xaMW0042/0061/00
8W0042/0061/008
tnerruCdetaRA8.12A5.01
egatloVylppuShp1/zH05/v011hp1/zH05/v032
gnitaresuFA31A31
ssalCnoitalusnI02
PI02PI

11
DECLARATION OF CONFORMITY