Clarke PGL1 User manual

INSTRUCTIONS FOR USE
GC07/23
PRESSURE GAUGE/PENLIGHT
MODEL NO: PGL1
PART NO: 4003537

2
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
INTRODUCTION
Thank you for purchasing this CLARKE Pressure Gauge/Worklight. Before
attempting to use this product, please read this manual thoroughly and follow
the instructions carefully. In doing so you will ensure the safety of yourself and
that of others around you, and you can look forward to your purchase giving
you long and satisfactory service.
CONTENTS
1 x Digital Pressure Gauge/LED Worklight
1 x Type-C USB Charging Cable
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for its intended purpose.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
ENVIRONMENTAL RECYCLING POLICY
Through purchase of this product, the customer is taking on the
obligation to deal with the WEEE in accordance with the WEEE
regulations in relation to the treatment, recycling & recovery and
environmentally sound disposal of the WEEE.
In effect, this means that this product must not be disposed of with general
household waste but according to the laws governing Waste Electrical and
Electronic Equipment (WEEE) at a recognised disposal facility.
The Lithium Ion battery falls under the Waste Batteries and Accumulators
Regulations 2009 and should be disposed of in a controlled manner.

3
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
TECHNICAL SPECIFICATIONS
SAFETY PRECAUTIONS
Please read the following instructions before use.
1. DO NOT shine the worklight into the eyes.
2. Ensure the device is fully charged before initial use.
3. DO NOT use the device during recharging.
4. Inspect the charging cable and connector for damage to ensure items
are safe before connecting to the power supply. If damaged do not use.
5. DO NOT disassemble the device for any reason.
6. Keep it out of reach of children.
7. DO NOT operate it with wet hands.
8. ALWAYS take care to maintain tyres to vehicle manufacturer’s
recommended pressures.
Digital Tyre Pressure Gauge
Pressure range 3-150 psi
Accuracy +/- 1%
Resolution 0.5 psi
Pressure Units PSI, BAR, KPa, Kg/cm2
Luminaire
Maximum Brightness 180 lumen
Charge Time 60-80 minutes
General characteristics
Dimensions 170 x 30 x 22 mm
Weight 0.90 g
Power Source Li-ion battery (3.7 V /750mAh)
Operating voltages 3.5 V (light) / 5V for USB charging
Approximate use from each charge Work light high -110 minutes
Work light low -180 minutes
Pen light - 180 mins

4
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
USING THE DEVICE
USING THE PRESSURE GAUGE
1. Press the button to power on. The
LCD will display for about
2 seconds and then display
00.0PSI [or other pressure units as
selected].
2. Align the tyre pressure gauge with
the air valve on the tyre and press
it home tightly. If the pressure is
stable for about 2 seconds the
correct pressure will be displayed.
3. Press the left switch incrementally and the screen will display the pressure
value in alternative units, (PSI, Bar, KPA, Kg/cm2, PSI).
4. The number is displayed for about 10 seconds before the display returns to
00.0. The gauge will automatically shut down in about 30 seconds.
5. Press the button for 2 seconds to manually power off.
NOTE: The device has been calibrated at the factory but a certified
pressure gauge may provide greater assurance of accuracy,
considering variations due to altitude.
USING THE LIGHTS
1. Press the LED button once to
switch on the end (pen) worklight.
2. Press the button a second time to
switch on the side worklight.
3. Press the button a third time to
make the worklight brighter.
4. Press the button again to switch
the worklight off.
5. Press the rear button at any time
to temporally switch the active lamp off.
CAUTION: NEVER LOOK AT THE WORKLIGHT BEAM. ALWAYS POINT IT
AWAY FROM YOURSELF AND NEVER POINT THE LIGHT AT ANOTHER
PERSON.

5
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
BATTERY CHARGING
1. Connect the charging cable to
any USB socket of an active
appliance or vehicle to charge
the battery.
• The display screen will
illuminate in green when the
lamp is charging with the
battery status shown in up to 4
black bars.
2. The worklight should not be
operated while using the charger.
3. The battery should be re-charged
after use or at least every 3
months. Failure to re-charge the
battery will lead to reduced
performance of the worklight and
to premature battery failure.
NOTE: The batteries cannot be
replaced.
POSITIONING
The unit is fitted with two magnets for positioning on a steel surface.
DAILY CARE
1. If you plan to store the worklight (e.g. for emergencies), we recommend
that the battery is fully charged before doing so, this will ensure the longest
possible battery life.
2. NEVER abuse the charging cable or yank the cable to disconnect it. Keep
the cable away from sharp edges/hot surfaces.
3. DO NOT leave the battery in a discharged state. Recharge the battery
after use.
4. To keep your worklight clean, wipe with a damp cloth only, DO NOT use
detergents, chemicals or harmful abrasives. NEVER immerse in water.
5. The light source of this device is not replaceable. When the light source
reaches its end of life the device must be replaced.

6
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
DECLARATION OF CONFORMITY-UK

7
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
DECLARATION OF CONFORMITY-CE