Clarke SHW1 User manual

USER INSTRUCTIONS
ORIGINAL INSTRUCTIONS GC0120 - ISS1
SAFETY HELMET
MODEL NO: SHW1(WHITE) & SHY1(YELLOW)
PART NO: 8133822 & 8133824

2
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
INTRODUCTION
Thank you for purchasing this CLARKE Safety Helmet. Before using this product,
please read this manual thoroughly and follow the instructions carefully. In
doing so you will ensure your safety and you can look forward to your
purchase giving you long and satisfactory service.
The SHW1/SHY1 (white/yellow) helmets have been designed to provide head
protection to meet the requirements of PPE Regulation (EU) 2016/425 and
EN397:2012+A1:2012.
The helmet is not suitable as PPE for climbing activities, fire fighting, sporting
activities such as cycling, skiing, equestrian, motorcycling etc. The helmet is
not designed to protect from heat hazards such as molten metal.
This helmet has been tested to withstand the following risks:
• Impact protection - maximum force transmitted up to 5kN, within a
temperature range of 50oC and -10oC
• Penetration by objects up to 3kg in weight, within a temperature
range of 50oC and -10oC
MATERIALS DECLARATION
No parts of the helmet are made of materials that are known to cause skin
irritation. However, materials that come into contact with the skin can cause
allergic reactions to certain susceptible individuals.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.

3
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
SAFETY PRECAUTIONS
The helmet should be checked each day before wearing to ensure that there
are no major surface defects such as crazing, cracks, deep scour marks,
discolouration or dents to the shell.
Never place this product on a hot surface.
FITTING AND ADJUSTMENT
For adequate protection the helmet must be adjusted to fit the user’s head
correctly. The helmet is adjustable for comfort and utility.
HEADBAND ADJUSTMENT
Horizontal headband adjustment is achieved by turning the adjuster.
Set the headband diameter with the
adjustment knob.
Twist clockwise to tighten and
counterclockwise to loosen
• The head band size is from 50-
66cm.
CHIN-STRAP ADJUSTMENT
1. Set the buckle on each side to
adjust the tension of the elastic
chinstrap.
2. Take care to set both side equally.

4
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
PRODUCT CARE
CARE & MAINTENANCE
Inspect the helmet regularly to ensure optimum performance. Defects of the
helmet/headgear must result in immediate replacement. If the shell or
headgear show any defects, immediate disposal and replacement of the
product is recommended. Give particular attention to the harness
attachment slots.
Significant impact to the helmet will result in reduced future protection, even if
visual physical deformation is not apparent. In any event, if any cracks are
detected, the helmet must be discarded immediately.
Do not apply tape, paint, solvents, adhesives or adhesive labels to the shell as
such application may reduce the effectiveness of the helmet.
CLEANING
The helmet can be wiped with soapy water or a household cleaning product
when dirty. Clean and/or disinfect all components regularly with a mild
detergent or disinfectant in luke warm water. Apply the cleaner with a clean
cloth or paper towel.
Do not use solvents for cleaning and always dry the helmet away from bright
sunlight or direct heat.
STORAGE
The helment should be transported and stored it its bag in cool, dry conditions
out of direct sunlight.
RECYCLING & THE ENVIRONMENT
If disposing of this product or any damaged components, do not dispose of
with general waste. This product contains re-usable raw materials. ABS plastic
products should be taken to your local civic amenity site for recycling into new
products.

5
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
COMPONENT PARTS
1 Helmet shell
2 Central headstrap with attachments
3 Diagonal headstrap with attachments
4 Rear adjustable headband
5 Fixed headband with fabric sweatband
6 Chin piece
7 Chin-strap connector
8 Chin-strap elastic
9 Rear headband adjuster

6
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
DECLARATION OF CONFORMITY

7
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
DECLARATION OF CONFORMITY