Clarke CAX20S User manual

USER INSTRUCTIONS
ORIGINAL INSTRUCTIONS GC0422
20 TONNE SHORT AXLE STAND
MODEL NO: CAX20S
PART NO: 7600029

2
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
SAFETY WARNINGS
•Read these instructions carefully before
use.
• Do not exceed the axle stands maximum
load (20 tonne each stand), The vehicle
weight will be stated in the owners
manual.
• Use only as specified in this manual.
• NEVER let children play in or around a
vehicle that is on axle stands.
• ALWAYS make sure that before you work
below the vehicle, a responsible person is
aware in case of injury or accident.
• Do not use more than one pair of axle
stands.
• Replace the warning label if it becomes
unreadable.
• Use only on a hard, flat surface, for
example concrete.
• Make sure that you chock all the wheels
that remain on the ground.
• Make sure that the supported vehicle
cannot move.
• Set each axle stand below an
appropriate strong point on the vehicle -
See your vehicle owners manual for
advice.
• Take care when using the axle stands on
a three-wheeled vehicle or trailer.
• Use stands as a matched pair to support
one end of a vehicle only.
• For your safety, never attempt to modify
these axle stands.
WARNING: NEVER WORK UNDER A VEHICLE SUPPORTED ONLY BY A JACK.
WARNING: AFTER LIFTING THE VEHICLE, SUPPORT IMMEDIATELY WITH
PROPERLY RATED AXLE STANDS.

3
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
USING THE AXLE STANDS
1. Refer to the vehicle handbook for
the correct jacking procedure and
location of support points.
2. Raise the vehicle using a suitable
lifting jack.
ADJUSTING THE AXLE STAND(S)
1. Raise the column to the required
height by rotating the handles while
hold the saddle to prevent it from
rotating.
• Turn the handles clockwise (looking
from above) to raise the saddle.
2. Position the axle stand under a
suitable supporting point. See your
vehicle manual for the location.
LOWERING THE VEHICLE
1. Slowly lower the vehicle onto the centre of the saddle.
REMOVING THE AXLE STANDS
1. Use a suitable jack to raise vehicle clear of the axle stands.
2. Remove stands.
3. Ensure that all tools, equipment and personnel are clear before carefully
lowering the vehicle to the ground.
WARNING: BEFORE USE, MAKE SURE THAT THERE IS NO DAMAGE TO ANY
PART OF THE AXLE STAND, IF THERE IS, DO NOT USE.
WARNING: DO NOT EXCEED THE RATED LOAD OF 20 TONNE PER STAND.
WARNING: IT MUST BE ENSURED THAT THE VEHICLE/LOAD IS CAREFULLY
LOCATED ONTO THE CENTRE OF THE AXLE STAND SADDLE. FAILURE TO DO
THIS CAN RESULT IN DAMAGE TO THE AXLE STANDS, LOSS OF SUPPORT TO
THE LOAD, SERIOUS PERSONAL INJURY OR LOSS OF LIFE.
WARNING: DO NOT LOAD THE STANDS OFF CENTRE. FAILURE TO HEED THIS
WARNING MAY CAUSE DAMAGE, INJURY OR LOSS OF LIFE.

SPECIFICATION
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
Product Dimensions (HxWxD) 330 x 330 x 630 mm (fully extended)
Maximum Support Height 600 mm
Minimum Support Height 410 mm
Maximum Load 20 tonne (20,000 kg) per stand
Product Weight 26.1 kg per stand