Clarke MA30 13B User guide

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •F a x : 8 0 0 . 26 3. 5111
Use and Maintenance
MA30™13B
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
When finished using
(*) ALWAYS FOLLOW THE DETERGENT DOSING RECOMMENDATION ON THE LABEL OF THE CHEMICAL PRODUCT USED.
2. Fill the solution tank with water.
The water temperature must not
exceed 105° F (40° C).
3. The tank cap can be used for dosing
the detergent. One full cap is 30 ml
giving 0.5% detergent of the 1.6 gal
(6 L) tank capacity. (*)
4. Adjust the handle to the desired
height. Turn the machine on with
the power button.
1. Disconnect the battery charger cord
from the machine and electrical
outlet.
17. Clean the debris collection tray.16. Clean the squeegee bars and the
cylindrical brush with water.
Check for wear and replace
when necessary.
15. Remove the squeegee bars.
Remove the cylindrical brush by
turning the side knob clockwise.
13. Remove the cover and clean it with
hot water. Remove the ball float
cage along with the float and clean
them thoroughly.
12. Empty the recovery and solution
tanks. Clean them out with water.
11. For transporting and parking the
machine, push the pedal down
(slightly lift the front of the machine
by tilting the handlebar).
5. Lift the pedal to lower the machine
and start working.
9. For double scrubbing, press the
vacuum suction button to switch the
vacuum off.
10. Turn the machine off with the
power button.
6. Grab the handles to activate the
brush and solution flow, then start
cleaning the floor.
7. Press the solution button to select
the type of cleaning required.
8. For sweeping functions, lift/lock the
right lever to lift the front squeegees
in order to collect light debris.
14. Check and clean the solution and
vacuum filters regularly.
19. Charge the batteries: Connect
the battery charger cord from the
machine to an electical outlet.
18. Clean the machine using a damp
cloth and where needed use a
neutral cleaning product.
20. Store the machine in a clean and
dry place.

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •F a x : 8 0 0 . 26 3. 5111
The machine
doesn’t work
as it should?
The suction
doesn’t work
as it should?
The machine
doesn’t clean
as it should?
The brush
doesn’t work
as it should?
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
Troubleshooting
MA30™13B
1. Adjust the brush pressure by turning
the regulation knob.
2. Check for brush wear, and make
sure that it is installed correctly.
3. Check to see if there is debris that is
preventing the brush from rotating.
(*) For these causes the maintenance
procedure must be performed by an
authorized Clarke Service Center.
For further information refer to the
Service Manual, available at any
Clarke Service Center.
1. Check if the battery is charged. 2. Check if the battery is correctly
fitting in the machine. (*)
3. Machine fault indicated by LED’s
blinking. (*)
1. Check to see if the solution filter is
dirty. Clean it if necessary.
2. Check if the holes in solution
dispensers are clogged. Remove
them and clean if needed.
3. Check to make sure the quick
connect valve is not leaking.
1. Check if the recovery tank is full. 2. Check if dirt and debris are clogging
the squeegee inlet and if the blades
are worn or damaged.
3. Rinse the inside of the duct recovery
hose with water.
4. Check if the float cage is clean.