Clarke Vantage 17 Battery User manual

Form No. 909 6772 000 - 06/2008
Vantage 17 Battery
Operator’s Manual
Manuel d’utilisation
Libro de Instrucciones
EN
ES
FR
READ THIS BOOK
LEA ESTE MANUAL
LISEZ CE MANUEL
English (3 - 24)
Español (25 - 47)
Français (48 - 70)
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your Clarke
machine could result in injury to you or to other personnel; damage to the machine or to other
property could occur as well. You must have training in the operation of this machine before using it.
If your operator(s) cannot read this manual, have it explained fully before attempting to operate this
machine.
All directions given in this book are as seen from the operator’s position at the rear of the machine.
For new books write to: Clarke®, 2100 Highway 265, Springdale, Arkansas 72764.

ENGLISH
EN
2 Operator’s Manual - Vantage 17 Battery
TABLE OF CONTENTS
Operator’s Manual 1
OPERATOR SAFETY INSTRUCTIONS 3
INTRODUCTION 5
HOW TO KEEP THIS MANUAL 5
IDENTIFICATION DATA 5
CHANGES AND IMPROVEMENTS 5
UNPACKING 5
MACHINE SPECIFICATIONS 6
MACHINE TRANSPORT PROCEDURES 7
SYMBOLS SHOWN ON THE MACHINE 7
MACHINE DESCRIPTION 8
OUTER STRUCTURE 8
INNER STRUCTURE 9
USE 11
BATTERY CHECK/SETTING ON A NEW MACHINE 11
(WET OR GEL) BATTERY SETTING, INSTALLATION AND CHARGING 12
BEFORE MACHINE START-UP 13
MACHINE START AND STOP 14
MACHINE OPERATION (SCRUBBING/DRYING) 15
MACHINE TRANSPORT/PARKING 15
TANK EMPTYING 16
AFTER USING THE MACHINE 16
RECOVERY TANK REMOVAL 17
STORED MACHINE 17
MAINTENANCE 18
SCHEDULED MAINTENANCE TABLE 18
SQUEEGEE CLEANING 19
SQUEEGEE BLADE CHECK AND REPLACEMENT 19
BRUSH CLEANING 20
CLEANING OF THE TANK AND VACUUM GRID FLOAT 20
SOLUTION FILTER CLEANING 21
MACHINE SPEED ADJUSTMENT 21
BATTERY CHARGING 22
FUSE CHECK/REPLACEMENT 23
Vantage 17 Battery ACCESSORIES/OPTIONS 24
HOW TO CORRECT PROBLEMS IN THE MACHINE 24
Parts List 71

ENGLISH EN
Operator’s Manual - Vantage 17 Battery 3
OPERATOR SAFETY INSTRUCTIONS
DANGER! Indicates a dangerous situation (risk of death) for the User.
WARNING! Indicates the risk for people of being injured and for objects of being damaged.
CAUTION! Indicates a caution or a remark related to important of useful functions. Pay particular attention
to the paragraphs marked by this symbol.
DANGER! This machine must be used by properly trained and authorized personnel only. Children or
disabled people cannot use this machine.
DANGER! When using lead (WET) batteries, battery charging produces highly explosive hydrogen gas.
During battery charging, remove the recovery tank assembly and perform this operation in
well-ventilated areas and away from naked flames. Do not smoke near the machine while charging
the batteries.
DANGER! When using lead (WET) batteries, keep sparks, flames and incandescent materials away from the
batteries. During normal operation, explosive gases are released.
DANGER! Do not operate the machine near toxic, dangerous, inflammable and/or explosive powders,
liquids or vapours.
DANGER! Disconnect the batteries before performing any maintenance/repair procedure.
DANGER! Do not wear jewels when working near electrical components.
WARNING! Before connecting the battery charger to the electrical mains, be sure that frequency and voltage
indicated in the related Manual correspond to the mains voltage.
WARNING! Do not charge batteries with damaged battery charger cable or plug. If the machine is not working
as it should, has been damaged, left outdoors or dropped into water, return it to the Service
Center.
WARNING! Do not pull or carry the machine by the battery charger cable; never use the battery charger cable
as a handle. Do not close a door on the supply cable, or pull the supply cable around sharp edges
or corners. Do not run the machine on the battery charger cable.
Keep the battery charger cable away from heated surfaces.
WARNING! To reduce the risk of fire, electric shock, or injury, do not leave the machine unattended when it
is plugged in.
WARNING! To avoid electric shock, do not expose to rain. Store the machine indoors.
WARNING! Do not allow to be used as a toy. Close attention is necessary when used near children.
WARNING! Use only as described in this Manual. Use only Clarke recommended accessories.
WARNING! Take all necessary precautions to prevent hair, jewerly and loose clothing from being caught in
the machine moving parts or vacuuming parts of the machine.
WARNING! Do not leave the machine unattended without being sure that the machine cannot move
independently.
WARNING! Do not use the machine on slopes with a gradient exceeding the specifications.

ENGLISH
EN
4 Operator’s Manual - Vantage 17 Battery
WARNING! Do not allow any object to enter into the openings. Do not use the machine if the openings are
clogged; always keep the openings free from dust, hair and any other foreign material which
could reduce the air flow.
WARNING! While using this machine, take care not to cause damage to people.
WARNING! Do not use the machine in particularly dusty areas.
WARNING! Do not put any can containing fluids on the machine.
WARNING! The machine working temperature must be between +32°F and +104°F (0°C and +40°C).
The storage temperature must be between +32°F and +104°F (0°C and +40°C).
The humidity must be between 30% and 95%.
WARNING! Always protect the machine against the sun, rain and bad weather, both under operation and
inactivity condition.
WARNING! Do not use the machine as a means of transport.
WARNING! Do not use the machine on slopes with an inclination higher than 2%.
WARNING! Do not allow the brush to operate while the machine is stationary to avoid damaging the floor.
WARNING! Do not bump into shelves or scaffoldings, particularly where there is a risk of falling objects.
WARNING! Do not tamper with the machine safety guards and follow the ordinary maintenance instructions.
WARNING! Do not remove or modify the plates affixed to the machine.
WARNING! In case of fire, use a powder fire extinguisher, not a water one.
WARNING! To ensure the proper and safe operation of the machine, have the scheduled maintenance and
repair, detailed in the relevant chapter of this Manual, performed by the authorized personnel or
an authorized Service Center.
WARNING! If parts must be replaced, require GENUINE spare parts from a Dealer or Authorized Retailer.
WARNING! Do not wash the machine with direct or pressurised water jets, or with corrosive substances.
WARNING! The machine must be disposed of properly, because of the presence of toxic-harmful materials
(batteries, electronic boards etc.), which are subject to standards that require disposal in special
centers (see Scrapping chapter).
WARNING! If the machine is used according to the instructions, the vibrations do not cause dangerous
situations. The machine vibration level is under 98.42 in/s2 (2.5 m/s2).
WARNING! Pay attention during the machine transfers when temperature is below freezing point. The water
in the recovery tank or in the hoses could freeze and seriously damage the machine.
WARNING! Use the brushes and the pads supplied with the machine and those specified in the Operator’s
Manual. Using other brushes or pads could reduce safety.
CAUTION! This machine contains lead acid batteries. The batteries must be disposed of in an
environmentally acceptable manner.

ENGLISH EN
Operator’s Manual - Vantage 17 Battery 5
The model of the Clarke scrubber-dryer ensures a highly effective floor cleaning performance. The Vantage 17 Battery model
uses a single rotary brush to clean an area of 17.0 in (430 mm) in width. The rear squeegee performs the floor cleaning and
the vacuum system recovers the washing water in a single pass.
HOW TO KEEP THIS MANUAL
The Instructions for Operator’s Manual must be kept near the machine, inside an adequate case, away from liquids and other
substances that can cause damage to it.
IDENTIFICATION DATA
The machine serial number and model are shown on the plate and can be read from the outside. (A, Fig. 2 - pag 8)
The machine model year is written in the Declaration of Conformity and it is also indicated by the first two figures of the machine
serial number.
This information is useful when requiring machine spare parts. Use the following table to write down the machine identification
data for any further reference.
CHANGES AND IMPROVEMENTS
Clarke constantly improves its products and reserves the right to make changes and improvements at its discretion without
being obliged to apply such benefits to the machines previously sold.
Any change and/or addition of accessories must be approved and performed by Clarke.
UNPACKING
To unpack the machine carefully follow the instructions on the packing.
When the machine is delivered, check that the packing and the machine were not damaged during transportation. In case of
visible damages, keep the packing and have it checked by the Carrier that delivered it. Call the Carrier immediately to fill in a
damage claim.
Please check that the following items have been supplied with the machine:
1. Technical documents:
– Scrubber-dryer operator's manual
– Electronic battery charger manual
2. 40A fuse
3. battery panels
INTRODUCTION
MACHINE Model: ______________________________
MACHINE Serial Number: _______________________

ENGLISH
EN
6 Operator’s Manual - Vantage 17 Battery
MACHINE SPECIFICATIONS
Model Vantage 17 Battery
Working Voltage 24 V
Standard Batteries (Quantity: 2) 12V 80 Ah, GEL
Drive Speed Determined by brush rotation
Battery Protection System Low Voltage Cut-Off of Brush and Solution
Vacuum Motor 300 W
Vacuum System Capacity 41.5 in H2O (1,055 mm H2O)
Solution Tank Capacity 8.2 gal (31 liters)
Solution Flow (min/max) 0.08/0.26 gal/min (0.3/1.0 liters/min)
Recovery Tank Capacity 7.7 gal (29 liters)
Squeegee Straight
Squeegee Width 28.3 in (720 mm)
Cleaning Width 17 in (430 mm)
Brush/Pad Motor 520 W
Brush/Pad Diameter 17 in (430 mm)
Brush/Pad Rotation Speed 135 RPM
Brush/Pad On-Floor Pressure (with Full Tank) 50.6 lbs (23 kg)
Central Wheels on Fixed Axle Diameter 9.8 in (250 mm)
Pivoting Wheel (diameter) 1.9 in (49 mm)
Wheel Pressure on the Ground Less than 0.37 ft/lbs2 (0.5 N/mm2)
On-Board Battery Charger 24V, 8/9 Amp., 100-240V
Maximum Floor Inclination 2 %
Machine Length 43.9 in (1115 mm)
Machine Width (without Squeegee) 22.4 in (570 mm)
Machine Height 41.4 in (1050 mm)
Machine Weight with Batteries, Brush and Full Solution
Tank (Working Condition) 346.1 lbs (157 kg)
Sound Pressure Level (at the Operator's Position) 67 dB(A)
Battery Compartment Size (Length x Width x Height) 13.8x13.8x10.2 in (350x350x260 mm)

ENGLISH
EN
7 Operator’s Manual - Vantage 17 Battery
How to Load and Unload the Machine from a Van or a
Truck
1. Check that the loading ramp is not longer than 8 feet (2.5
m) and not wider than 40 inches (1 m). Its thickness must
be adequate to support the machine and operators'
weight.
2. Check that the ramp is dry and clean.
3. Position the ramp properly.
4. Before loading the machine, remove the squeegee
assembly and the brush/pad holder. Before loading the
machine, empty both the solution and the recovery tank.
How to Fasten the Machine Inside the Vehicle
5. Clarke recommends tying down machine when
transporting.
MACHINE TRANSPORT PROCEDURES
WARNING!
This machine is heavy. Machine transfer must be
performed by qualified personnel only. Machine
transfer on steep ramps must be performed by two
well-trained operators only. Always move it slowly.
Do not turn the machine on slopes. Do not leave the
machine unattended on slopes. Loading ramp width
must not be less than 40 in (1 m).
Figure 1
SYMBOLS SHOWN ON THE MACHINE
WARNING!
Carefully read all maintenance/repair instructions before performing any
maintenance/repair procedure.
WARNING!
Do not wash the machine with pressurized water.
WARNING!
Do not open the cover. Electric danger!

ENGLISH
EN
8 Operator’s Manual - Vantage 17 Battery
OUTER STRUCTURE
(See Fig. 2)
A. Serial number plate/technical data
B. Handlebar
C. Control panel
D. Solution flow control lever
E1. ECO Solution Flow Position
E2. Maximum solution flow position
F. Recovery tank cover
G. Rear support wheel for transport/parking
H. Central wheels on fixed axle
I. Brush/pad-holder with pad
J. Brush/pad-holder cover
K. Squeegee
L. Squeegee knobs
M. Front squeegee blade
N. Rear squeegee blade
O. Squeegee blade fixing springs
P. Recovery tank drain hose
MACHINE DESCRIPTION
Q. Recovery tank drain hose bracket
R. Solution drain valve
S. Squeegee lifting/lowering lever
T. Solution filter
U. Battery charger cable
V. Squeegee vacuum hose
W. Transport/parking device
W1.Transport/parking device activated
W2.Transport/parking device deactivated
X. Transport/parking device positioning pin
Y. Electrical component box
Z. Battery charger
AA. Battery charger warning lights
AB. Battery installation diagram
AC. Recovery tank
AD. Solution tank
Figure 2

ENGLISH EN
Operator’s Manual - Vantage 17 Battery 9
INNER STRUCTURE
(See Fig. 3)
A. Recovery tank cover (open)
B. Recovery tank cover gasket
C. Cover stand (applied)
D. Recovery tank
E. Solution tank
F. Vacuum grid with automatic shut-off float
G. Recovery water drain hole
H. Vacuum motor
I. Brush/pad motor
J. Batteries
K. Battery installation diagram
L. Cover with brush/pad-holder coupling pin
M. Machine speed adjusting screw
N. Brush
O. Pad-holder
P. Pad
Q. Vent hole
Figure 3

ENGLISH
EN
10 Operator’s Manual - Vantage 17 Battery
CONTROL PANEL
(See Fig. 4)
Charged Battery Indicator Light (Green) (A, Fig. 4)
When it turns on, it indicates that the batteries are charged.
Half-discharged Battery Indicator Light (Yellow) (B, Fig. 4)
When it turns on, it indicates that the batteries are half discharged.
Discharged Battery Indicator Light (Red) (C, Fig. 4)
When it turns on, it indicates that the batteries are discharged. Do not use the machine with discharged batteries, to avoid
damaging the batteries, but charge them (see the procedure in the Maintenance chapter).
Brush/Pad Rotation Switch (D, Fig. 4)
When it is turned to the "I" position, the machine is ready to start the brush/pad rotation. To start the brush/pad rotation, press
and hold one or both the activation switches (F, Fig. 4).
When it is turned to the "0" position, the brush/pad rotation is deactivated.
Water Vacuuming Switch (E, Fig. 4)
When it is turned to the "I" position, it starts the vacuuming of the recovery water.
When it is turned to the "0" position, it stops the vacuuming of the recovery water.
Activation Switches (F, Fig. 4)
When one or both the activation switches are pressed, the brush/pad rotation is activated.
The switches are active only if the brush/pad rotation switch (D, Fig. 4) is turned to the "I" position.
Figure 4

ENGLISH EN
Operator’s Manual - Vantage 17 Battery 11
While reading this Manual, the Operator must pay particular
attention to the symbols shown in the plates.
Do not cover these plates for any reason and immediately
replace them if damaged.
BATTERY CHECK/SETTING ON A NEW MACHINE
The machine is supplied with GEL batteries already
installed and ready to be used.
– Turn the brush/pad rotation switch and the water
vacuuming switch (A and B, Fig. 6) to the "I" position. If
the green warning light (C) turns on, the batteries are
ready to be used.
– If the yellow or red warning light (D or E, Fig. 6) turns on,
it is necessary to charge the batteries before using the
machine (see the procedure in the Maintenance
chapter).
USE
WARNING!
On some points of the machine there are some
labels indicating:
– DANGER
– WARNING
– CAUTION
– INFORMATION
WARNING!
The electric components of this machine can be
seriously damaged if batteries are either installed or
connected improperly. The batteries must be
installed by qualified personnel only.
Check the batteries for damage before installation.
Handle the batteries with great care.
Install the battery terminal caps supplied with the
machine.
Figure 5
Figure 6

ENGLISH
EN
12 Operator’s Manual - Vantage 17 Battery
(WET OR GEL) BATTERY SETTING,
INSTALLATION AND CHARGING
The electrical board of the machine is to be set according to
the type of batteries installed, either gel (GEL) or lead (WET).
Proceed as follows:
Machine Setting
1. The machine factory setting is for GEL batteries; if this
setting corresponds to the type of batteries bought, go to
step 5. Otherwise, carry out steps 2, 3, and 4 too.
2. Remove the screws (A, Fig. 7) and carefully pull out the
electrical component box cover (B).
3. Push the microswitch (C, Fig. 7) downwards to WET
position.
4. Reinstall the electrical component box cover (B, Fig. 7)
and tighten the screws (A).
Battery Installation
5. Disconnect the vacuum hose (A, Fig. 8) from the
squeegee (B).
6. Disconnect the recovery tank drain hose (C, Fig. 8) from
the bracket (D).
7. Open the cover (A, Fig. 9) and apply the cover stand (B).
8. Grasp the recovery tank (C, Fig. 9) in the area (D) and lift
it, as shown in the figure, then disconnect the vacuum
hose (E) from the tank and remove the tank (C) together
with the hoses (F) and (G).
9. Install the batteries on the machine according to the
diagram (E, Fig. 8).
10. Reinstall the tank (C, Fig. 9) by carrying out steps 5 to 9
in the reverse order.
Battery Charging
11. Charge the batteries (see the relevant procedure in the
Maintenance chapter).
WARNING
Do not move the adjacent switch (D, Fig. 7).
Figure 7
Figure 8
Figure 9

ENGLISH EN
Operator’s Manual - Vantage 17 Battery 13
BEFORE MACHINE START-UP
To prepare the machine for operation, follow this procedure
before start-up.
Squeegee Installation
1. Install the squeegee (A, Fig. 10) and fix it by means of the
squeegee knobs (B), then connect the vacuum hose (C)
to the squeegee.
Solution Tank Filling
2. Fill the solution tank (A, Fig. 11) with a solution suitable
for the work to be carried out.
Do not fill the solution tank completely, leave few inches
from the edge.
Always follow the dilution instructions on the container
label on the chemical product used to create the solution.
The solution temperature must not exceed 100°F (40°C).
Brush or Pad-Holder Installation
3. Deactivate the transport/parking device (A, Fig. 12) by
putting it in position (B) after inserting the relevant pin (C).
4. Lift the brush cover (D, Fig. 12) by prying the handlebar
(E).
5. Place the brush (B, Fig. 11) or the pad-holder (C) with
pad (D) under the cover.
6. Lower the cover (D, Fig. 12) by means of the handlebar
(E).
7. Press the brush push-button on “I” (Fig. 12, F), then press
on or both push-buttons (Fig. 12, G) for a few seconds.
If the hooking operation is difficult, manually rotate the
brush/pad-holder counterclockwise (Fig. 13).
CAUTION
Use only low-foam and non-flammable liquid
detergents, intended for automatic scrubber
applications.
NOTE
According to the kind of cleaning to be carried out,
the machine can be equipped both with the brush (B,
Fig. 11) and the pad-holder (C) with pad (D).
Figure 10
Figure 11
Figure 12
Figure 13

ENGLISH
EN
14 Operator’s Manual - Vantage 17 Battery
MACHINE START AND STOP
Start
1. Prepare the machine according to the procedure shown
in the previous paragraph.
2. Lower the squeegee (A, Fig. 15) by pushing the lever (B)
downwards.
3. Turn the solution flow control lever (C, Fig. 15) to one of
the following positions, according to the type of cleaning
to be carried out:
–ECO system: When the lever (C, Fig. 15) is in the
"ECO" position (D), the machine works in a special
condition of programmed water "economy" usage; as
the water flow is set and constant, the machine can
work with a cleaning time of 70-80 minutes [0.08
gal/min (0.3 liters/min].
–Variable system: When the lever is turned to the left
(variable flow), it is possible to increase the capacity
up to 0.26 gal/min (1 liter/min) (E, Fig. 15).
During machine operation, it is not possible to completely
close the water flow to the brush/pad.
4. Turn the switches (A and B, Fig. 14) to the "I" position.
5. While keeping both hands on the handlebar (G, Fig. 15),
start the machine by pressing one or both the activation
switches (F).
Machine Stop
6. Release the switches (F, Fig. 15).
7. Turn the switches (A and B, Fig. 14) to the "0" position.
8. Lift the squeegee by pushing the lever (B, Fig. 15)
completely upwards.
9. Lift the brush/pad by activating (B, Fig. 16) the
transport/parking device (A) after inserting the relevant
pin (C).
NOTE
If the green indicator light (C, Fig. 14) turns on, the
machine is ready to be used.
If the yellow (D) or red indicator light (E) turns on, it
is necessary to charge the batteries (see the
procedure in the Maintenance chapter).
Figure 14
Figure 15
Figure 16

ENGLISH EN
Operator’s Manual - Vantage 17 Battery 15
MACHINE OPERATION (SCRUBBING/DRYING)
1. Start the machine according to the procedure shown in
the previous paragraph.
2. While keeping both hands on the handlebar (D, Fig. 18),
move the machine and start scrubbing/drying the floor.
3. If necessary, adjust the solution flow sent to the
brush/pad by turning the lever (B, Fig. 18).
Battery Discharge During Operation
4. Until the green indicator light (A, Fig. 17) stays on, the
batteries allow the machine to operate normally.
When the green indicator light (A) turns off and the yellow
(B) and red (C) warning indicator lights turn on in
sequence, it is necessary to charge the batteries.
Machine Speed Adjustment
5. The machine speed depends on the type of floor to be
cleaned and on the choice of using brush or pad.
If necessary, it is possible to adjust the machine speed by
following the relevant procedure in the Maintenance
chapter.
MACHINE TRANSPORT/PARKING
After operation, proceed as follows to transport/park the
machine.
1. Turn the brush/pad rotation switch and the water
vacuuming switch (D and E, Fig. 17) to the "0" position.
2. Lift the squeegee by pushing the lever (C, Fig. 18)
upwards.
3. Grasp the handlebar (A, Fig. 19) and slightly lower it until
the rear wheel (B) comes into contact with the floor, as
shown in the figure. While holding the machine in this
position, push it to the transport/parking area.
CAUTION:
To avoid damaging the floor surface:
– Do not use the brush/pad without the solution.
– When the machine is stopped, stop the
brush/pad by releasing the switches (A, Fig. 18).
CAUTION:
Before lifting the brush/pad, stop its rotation by
releasing the switches (A, Fig. 18).
CAUTION:
Do not use the machine with discharged batteries, to
avoid damaging the batteries and reducing the
battery life.
Figure 17
Figure 18
Figure 19

ENGLISH
EN
16 Operator’s Manual - Vantage 17 Battery
TANK EMPTYING
An automatic float shut-off system (A, Fig. 20) deactivates the
vacuum system once the recovery tank (B) is full.
The vacuum system shutdown is due to the recovery tank
filling, which prevents recovery water from being vacuumed,
and it is signalled by a sudden increase in the system motor
noise frequency.
When the recovery tank (B, Fig. 20) is full, empty it according
to the following procedure.
Recovery Tank Emptying
1. Stop the machine by turning the brush/pad rotation
switch and the water vacuuming switch (A and B, Fig. 21)
to the "0" position.
2. Lift the squeegee by means of the lever (C, Fig. 21).
3. Push the machine to the appointed disposal area.
4. Insert the positioning pin (E), lift the brush/pad and
activate the transport/parking device (D, Fig. 21) by
means of the handlebar.
5. Disconnect the recovery tank drain hose (F, Fig. 21) from
the bracket (G); open the cover (H), then lower the hose
(F) and empty the recovery tank. Then, rinse the tank
with clean water.
Solution Tank Emptying
6. Carry out steps 1 to 4.
7. Empty the solution tank by opening the drain valve (I, Fig.
21). Then, rinse the tank with clean water.
AFTER USING THE MACHINE
After scrubbing-drying, before leaving the machine:
1. Remove the brush/pad-holder as follows:
– Turn the brush/pad rotation switch (A, Fig. 21) to the
"I" position.
– Lift the brush/pad-holder and press one or both the
switches (J, Fig. 21) for a few seconds, then release
them: this causes the brush/pad-holder to be
disengaged.
2. Empty the tanks (B and C, Fig. 20) according to the
procedure shown in the previous paragraph.
3. Perform the maintenance operations to be carried out
after using the machine (see the Maintenance chapter).
4. Store the machine in a clean and dry place, with the
brush/pad and the squeegee lifted or removed.
Figure 20
Figure 21

ENGLISH EN
Operator’s Manual - Vantage 17 Battery 17
RECOVERY TANK REMOVAL
To check the batteries, or to perform other operations, it may
be necessary to remove the recovery tank (A, Fig. 23)
according to the following procedure:
1. Empty the tank (A, Fig. 23) according to the procedure
shown in the relevant paragraph.
2. Drive the machine on a level ground.
3. Make sure that the switches (A and B, Fig. 22) are in the
"0" position.
4. Disconnect the vacuum hose (C, Fig. 22) from the
squeegee (D).
5. Disconnect the recovery tank drain hose (E, Fig. 22) from
the bracket (F).
6. Open the cover (B, Fig. 23) and apply the cover stand
(C).
7. Grasp the recovery tank (A, Fig. 23) in the area (D) and
slightly lift it, as shown in the figure.
8. Disconnect the vacuum hose (E, Fig. 23) from the tank,
then remove the tank (A) with the hoses (F) and (G).
STORED MACHINE
If the machine is not going to be used for more than 30 days,
proceed as follows:
1. Perform the operations described in the After Using the
Machine paragraph.
2. Remove the recovery tank (A, Fig. 23) according to the
procedure shown in the previous paragraph, then
disconnect the battery negative terminals.
3. Reinstall the recovery tank (A, Fig. 23).
4. Store the machine in a clean and dry place, with the
brush/pad and the squeegee lifted or removed.
Figure 22
Figure 23

ENGLISH
EN
18 Operator’s Manual - Vantage 17 Battery
The lifespan of the machine and its maximum operating safety are ensured by correct and regular maintenance.
Provided below is the Scheduled Maintenance Table. The intervals shown may vary according to particular working conditions,
which are to be defined by the person in charge of the maintenance.
This Manual contains the Scheduled Maintenance Table and describes only the easiest and most common maintenance
procedures.
SCHEDULED MAINTENANCE TABLE
(1): and after the first 8 working hours
(2): for these maintenance operations, contact an authorized Clarke Service Center
MAINTENANCE
WARNING!
All maintenance operations must be performed by qualified personnel, or by an authorized Service Center.
WARNING!
Maintenance operations must be carried out:
– With the machine switched off
– With the battery disconnected
– With the battery charger-electrical mains connecting cable disconnected
Moreover, read carefully the instructions in the Operator Safety Instructions chapter before performing any
maintenance operation.
Procedure
Daily or after
using the
machine
Weekly Every six
months Yearly
Squeegee Cleaning z
Brush Cleaning z
Tank and Vacuum Grid with Float Cleaning z
Battery Charging z
Squeegee Blade Check and Replacement z
Solution Filter Cleaning z
Screw and Nut Tightening Check z(1)
Brush Motor Carbon Brush Check or Replacement z(2)
Vacuum Motor Carbon Brush Check or Replacement z(2)

ENGLISH EN
Operator’s Manual - Vantage 17 Battery 19
SQUEEGEE CLEANING
1. Make sure that the switches (A and B, Fig. 24) are in the
"0" position.
2. Lower the squeegee (D, Fig. 24) by means of the lever
(C).
3. Disconnect the vacuum hose (E, Fig. 24) from the
squeegee.
4. Loosen the squeegee knobs (F, Fig. 24) and remove the
squeegee (D).
5. Wash and clean the squeegee assembly to remove dirt
and debris.
6. Check the front blade (C, Fig. 25) and the rear blade (D)
for wear, cuts and tears; if required, replace them
according to the procedure in the “Squeegee Blade
Check and Replacement“ section below.
7. Reassemble in the reverse order of disassembly.
SQUEEGEE BLADE CHECK AND REPLACEMENT
1. Clean the squeegee according to the procedure shown in
the previous paragraph.
2. Check that the edge (E, Fig. 25) of the front blade and the
edge (F) of the rear blade lay down on the same level,
along their length; otherwise adjust their height according
to the following procedure:
– Remove the fixing springs (G, Fig. 25) and adjust the
front blade (C) and the rear blade (D).
– Reinstall the fixing springs on the properly adjusted
front and rear blades.
3. Check the front blade (C, Fig. 25) and rear blade (D) for
wear, cuts and tears. If necessary, replace them
according to the following procedure:
– Remove the spring clamp (G, Fig. 25) and replace the
blade.
– Reinstall the spring clamps (G, Fig. 25).
4. Reinstall the squeegee (D, Fig. 24) and screw down the
squeegee knobs (F).
5. Connect the vacuum hose (E, Fig. 24) to the squeegee
(D).
NOTE
The squeegee must be clean and the blades must be
in good condition in order for the floor to dry
properly.
CAUTION
It is advisable to use protective gloves when
cleaning the squeegee because there may be cutting
debris.
NOTE: When replacing the blades, make sure that
the ribs of the front blade face the front and the ribs
of the rear blade face the rear.
Figure 24
Figure 25

ENGLISH
EN
20 Operator’s Manual - Vantage 17 Battery
BRUSH CLEANING
1. Remove the brush from the machine, according to the
procedure shown in the Use chapter.
2. Clean and wash the brush with water and detergent.
3. Check the brush bristles for integrity and wear; if
necessary, replace the brush.
CLEANING OF THE TANK AND VACUUM GRID
FLOAT
1. Push the machine to the appointed disposal area.
2. Make sure that the switches (A and B, Fig. 26) are in the
"0" position.
3. Lift the cover (A, Fig. 27) and apply the cover stand (B),
then clean and wash the cover, the tanks (C and D) and
the vacuum grid (E) with clean water.
Drain the water from the tanks by means of the drain
hose (C, Fig. 26) and valve (D).
4. If necessary, release the retainers (F, Fig. 27), open the
vacuum grid (E), remove the float (G), then carefully
clean and reinstall them.
5. Check the cover sealing gasket (H, Fig. 27) of the
recovery tank for wear.
If necessary, replace the gasket (H, Fig. 27) after
removing it from the housing (I).
When reassembling the new gasket, install the joint (J) in
the central area, as shown in Fig. 27.
6. Check the gasket (H, Fig. 27) seating surface (K) for
integrity and sealing capabilities.
7. Check the vent hole (L, Fig. 27). If clogged, clean it.
8. Remove the cover stand (B, Fig. 27) and close the cover
(A).
CAUTION
It is advisable to use protective gloves when
cleaning the brush because there may be cutting
debris.
NOTE
The gasket (H, Fig. 27) creates vacuum in the tank,
which is necessary for the vacuuming of the
recovery water.
NOTE
The hole (L, Fig. 27) compensates the air in the cover
interspaces, thus allowing the creation of vacuum in
the recovery tank.
Figure 26
Figure 27