Clarke Vantage 17 E User manual

Vantage 17 E
READ THIS BOOK
LEA ESTE MANUAL
LISEZ CE MANUEL
EN
ES
FR
Form No. 9099653000 - 07/2012
English (1 - 22)
Español (23 - 44)
Français (45 - 66)
This book has important information for the use and safe operation of this machine. Failure to read this
book prior to operating or attempting any service or maintenance procedure to your Clarke machine
could result in injury to you or to other personnel; damage to the machine or to other property could
occur as well. You must have training in the operation of this machine before using it. If your operator(s)
cannot read this manual, have it explained fully before attempting to operate this machine.
All directions given in this book are as seen from the operator’s position at the rear of the machine.
Instructions For Use - Original Instructions / Instrucciones de uso / Mode d’ emploi
Model: 9087316020
9099653000 - 07-2012.indb 1 24-Jul-12 15:17:38

9099653000 - 07-2012.indb 2 24-Jul-12 15:17:38

INSTRUCTIONS FOR USE ENGLISH
9099653000 - VANTAGE 17 E 1
TABLE OF CONTENTS
INTRODUCTION.............................................................................................................................................................. 2
MANUAL PURPOSE AND CONTENTS .......................................................................................................................................... 2
TARGET........................................................................................................................................................................................... 2
HOW TO KEEP THIS MANUAL....................................................................................................................................................... 2
IDENTIFICATION DATA................................................................................................................................................................... 2
OTHER REFERENCE MANUALS................................................................................................................................................... 2
SPARE PARTS AND MAINTENANCE............................................................................................................................................. 2
CHANGES AND IMPROVEMENTS ................................................................................................................................................ 2
OPERATION CAPABILITIES........................................................................................................................................................... 2
CONVENTIONS .............................................................................................................................................................................. 2
UNPACKING/DELIVERY ................................................................................................................................................. 3
SAFETY ........................................................................................................................................................................... 3
VISIBLE SYMBOLS ON THE MACHINE......................................................................................................................................... 3
SYMBOLS THAT APPEAR ON THIS MANUAL............................................................................................................................... 4
GENERAL INSTRUCTIONS............................................................................................................................................................ 4
120 VAC GROUNDING INSTRUCTIONS ....................................................................................................................................... 6
MACHINE DESCRIPTION ............................................................................................................................................... 7
MACHINE STRUCTURE ................................................................................................................................................................. 7
HANDLEBAR AND CONTROL PANEL............................................................................................................................................ 9
ACCESSORIES/OPTIONS.............................................................................................................................................................. 9
TECHNICAL DATA......................................................................................................................................................................... 10
WIRING DIAGRAM.........................................................................................................................................................................11
GROUNDING CONNECTION ........................................................................................................................................................11
USE ................................................................................................................................................................................ 12
BEFORE MACHINE START-UP.................................................................................................................................................... 12
MACHINE START AND STOP....................................................................................................................................................... 13
MACHINE OPERATION (SCRUBBING/DRYING)......................................................................................................................... 14
MACHINE TRANSPORT/PARKING .............................................................................................................................................. 15
TANK EMPTYING.......................................................................................................................................................................... 15
AFTER USING THE MACHINE..................................................................................................................................................... 16
RECOVERY TANK REMOVAL ...................................................................................................................................................... 16
MACHINE LONG INACTIVITY ...................................................................................................................................................... 16
FIRST PERIOD OF USE ............................................................................................................................................................... 16
MAINTENANCE............................................................................................................................................................. 17
SCHEDULED MAINTENANCE TABLE ......................................................................................................................................... 17
SQUEEGEE CLEANING ............................................................................................................................................................... 18
SQUEEGEE BLADE CHECK AND REPLACEMENT.................................................................................................................... 18
BRUSH CLEANING....................................................................................................................................................................... 19
TANK AND VACUUM GRID CLEANING ....................................................................................................................................... 19
SOLUTION FILTER CLEANING.................................................................................................................................................... 20
MACHINE SPEED ADJUSTMENT ................................................................................................................................................ 20
TROUBLESHOOTING................................................................................................................................................... 21
SCRAPPING .................................................................................................................................................................. 22
PARTS LIST................................................................................................................................................................... 67
9099653000 - 07-2012.indb 1 24-Jul-12 15:17:38

ENGLISH INSTRUCTIONS FOR USE
2VANTAGE 17 E - 9099653000
INTRODUCTION
NOTE
The numbers in brackets refer to the components shown in Machine Description chapter.
MANUAL PURPOSE AND CONTENTS
The purpose of this Manual is to provide the operator with all necessary information to use the machine properly, in a safe and
autonomous way. It contains information about technical data, safety, operation, storage, maintenance, spare parts and disposal.
Before performing any procedure on the machine, the operators and qualied technicians must read this Manual carefully. Contact
Clarke in case of doubts concerning the interpretation of the instructions and for any further information.
TARGET
This Manual is intended for operators and technicians qualied to perform the machine maintenance.
The operators must not perform procedures reserved for qualied technicians. Clarke will not be answerable for damages coming
from the non-observance of this prohibition.
HOW TO KEEP THIS MANUAL
The User Manual must be kept near the machine, inside an adequate case, away from liquids and other substances that can cause
damage to it.
IDENTIFICATION DATA
The machine model and serial number are marked on the plate (1).
Product code and year of production are marked on the same plate.
This information is useful when requiring machine spare parts. Use the following table to write down the machine identication data.
MACHINE model ...............................................................................
PRODUCT code ................................................................................
MACHINE serial number ...................................................................
OTHER REFERENCE MANUALS
– Spare Parts List (supplied with the machine)
– Service Manual (that can be consulted at Clarke Service Centers)
SPARE PARTS AND MAINTENANCE
All necessary operating, maintenance and repair procedures must be performed by qualied personnel or by Clarke Service
Centers. Only original spare parts and accessories must be used.
Contact Clarke for service or to order spare parts and accessories, specifying the machine model, product code and serial number.
CHANGES AND IMPROVEMENTS
Clarke constantly improves its products and reserves the right to make changes and improvements at its discretion without being
obliged to apply such benets to the machines that were previously sold.
Any change and/or addition of accessories must be approved and performed by Clarke.
OPERATION CAPABILITIES
These scrubber-dryers are used to clean (scrubbing and drying) smooth and solid oors, in civil or industrial environment, under
safe operation conditions by a qualied operator.
The scrubber-dryers cannot be used for tted carpet and carpet cleaning.
CONVENTIONS
Forward, backward, front, rear, left or right are intended with reference to the operator’s position, that is to say in driving position
with the hands on the handlebar (2).
9099653000 - 07-2012.indb 2 24-Jul-12 15:17:38

INSTRUCTIONS FOR USE ENGLISH
9099653000 - VANTAGE 17 E 3
UNPACKING/DELIVERY
To unpack the machine, carefully follow the instructions on the packing.
When the machine is delivered, check that the packing and the machine were not damaged during transportation.
In case of visible damages, keep the packing and have it checked by the carrier that delivered it. Call the carrier immediately to ll
in a damage claim.
Please check that the following items have been supplied with the machine:
– Technical documents:
• Scrubber-dryer User Manual
• Scrubber-dryer Spare Parts List
WARNING!
The Products sold with this Manual contain or may contain chemicals that are known to certain governments
(such as the State of California, as identied in its Proposition 65 Regulatory Warning Law) to cause cancer,
birth defects or other reproductive harm. In certain locations (including the State of California) purchasers of
these Products that place them in service at an employment job site or a publicly accessible space are required
by regulation to make certain notices, warnings or disclosures regarding the chemicals that are or may be
contained in the Products at or about such work sites. It is the purchaser’s responsibility to know the content
of, and to comply with, any laws and regulations relating to the use of these Products in such environments.
The Manufacturer disclaims any responsibility to advise purchasers of any specic requirements that may be
applicable to the use of the Products in such environments.
SAFETY
The following symbols indicate potentially dangerous situations. Always read this information carefully and take all necessary
precautions to safeguard people and property.
The operator’s cooperation is essential in order to prevent injury. No accident prevention program is effective without the total
cooperation of the person responsible for the machine operation. Most of the accidents that may occur in a factory, while working
or moving around, are caused by failure to comply with the simplest rules for exercising prudence. A careful and prudent operator is
the best guarantee against accidents and is essential for successful completion of any prevention program.
VISIBLE SYMBOLS ON THE MACHINE
WARNING!
Carefully read all the instructions before performing any operation on the machine.
WARNING!
Do not wash the machine with direct or pressurized water jets.
max.2%
WARNING!
Do not use the machine on slopes with a gradient exceeding the specications.
9099653000 - 07-2012.indb 3 24-Jul-12 15:17:39

ENGLISH INSTRUCTIONS FOR USE
4VANTAGE 17 E - 9099653000
SYMBOLS THAT APPEAR ON THIS MANUAL
DANGER!
It indicates a dangerous situation with risk of death for the operator.
WARNING!
It indicates a potential risk of injury for people.
CAUTION!
It indicates a caution or a remark related to important or useful functions.
Pay careful attention to the paragraphs marked by this symbol.
NOTE
It indicates a remark related to important or useful functions.
CONSULTATION
It indicates the necessity to refer to the User Manual before performing any procedure.
GENERAL INSTRUCTIONS
Specic warnings and cautions to inform about potential damages to people and machine are shown below.
DANGER!
–Before performing any cleaning, maintenance, repair or replacement procedure, turn the main switch (26) to
“0” and disconnect the plug from the mains socket.
–This machine must be used by properly trained operators only.
–Do not wear jewels when working near electrical components.
–Do not work under the lifted machine without supporting it with safety stands.
–Do not operate the machine near toxic, dangerous, ammable and/or explosive powders, liquids or vapors:
This machine is not suitable for collecting dangerous powders.
WARNING!
–Carefully read all the instructions before performing any maintenance/repair procedure.
–The machine power supply cable is grounded and the relevant plug is grounded too. In case of machine
malfunction or breakdown, grounding connection reduces the risk of electric shock.
–The power supply cable plug must be connected to an appropriate outlet, which is grounded according to
law in force.
–Improper connection can cause electric shock. Consult a qualied technician to make sure that the outlet is
properly grounded.
–Do not tamper with the power supply cable plug. If the power supply cable plug cannot be connected to the
outlet, have new grounded outlet installed by a qualied technician, according to the law in force.
–Before connecting the power supply plug to the electrical mains, check that frequency and voltage, shown
on the machine serial number plate (1), match the electrical mains voltage.
–Do not unplug the machine by pulling the supply cable. To unplug, grasp the plug, not the cable.
–Do not handle the plug or the machine with wet hands.
–Turn off all controls before unplugging.
–Regularly check the power supply cable for damages, cracks, cuts and wear. If necessary, replace it.
–If the power supply cable is damaged, it must be replaced by the Manufacturer or by an authorised Service
Centre.
–To avoid any risk, if the power supply cable is damaged, contact the Clarke Service Center or a qualied
technician.
9099653000 - 07-2012.indb 4 24-Jul-12 15:17:39

INSTRUCTIONS FOR USE ENGLISH
9099653000 - VANTAGE 17 E 5
WARNING!
–Do not pull or carry the machine by the power supply cable and never use the power supply cable as a
handle. Do not close a door on the power supply cable, or pull the power supply cable around sharp edges
or corners. Do not run the machine on the power supply cable.
–The rotating brush must not come into contact with the power supply cable.
–Keep the supply cable away from heated surfaces.
–To reduce the risk of re, electric shock, or injury, do not leave the machine unattended when it is plugged
in. Disconnect the machine from the electrical mains when not in use and before performing maintenance
procedures.
–Always protect the machine against the sun, rain and bad weather, both under operation and inactivity
condition. Store the machine indoors, in a dry place: This machine must be used in dry conditions, it must
not be used or kept outdoors in wet conditions.
–Before using the machine, close all doors and/or covers as shown in the User Manual.
–This machine is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the machine by a person responsible for they safety.
Children should be supervised to ensure that they do not play with the machine.
–Close attention is necessary when used near children.
–Use only as shown in this Manual. Only Clarke recommended accessories must be used.
–Check the machine carefully before each use, always check that all the components have been assembled
before use. If the machine is not perfectly assembled it can cause damages to people and properties.
–Take all necessary precautions to prevent hair, jewels and loose clothes from being caught by the machine
moving parts.
–Do not use the machine on slopes with a gradient exceeding the specications.
–Do not use the machine on incline.
–Do not tilt the machine more than the angle indicated on the machine itself, in order to prevent instability.
–Do not use the machine in particularly dusty areas.
–Use the machine only where a proper lighting is provided.
–While using this machine, take care not to cause damage to people or objects.
–Do not bump into shelves or scaffoldings, especially where there is a risk of falling objects.
–Do not lean liquid containers on the machine, use the relevant can holder.
–The machine operating temperature must be between +32°F and +104°F (0°C and +40°C).
–The machine storage temperature must be between +32°F and +104°F (0°C and +40°C).
–The humidity must be between 30% and 95%.
–When using oor cleaning detergents, follow the instructions on the labels of the detergent bottles.
–To handle oor cleaning detergents, wear suitable gloves and protections.
–Do not use the machine as a means of transport.
–Do not allow the brush/pad to operate while the machine is stationary to avoid damaging the oor.
–In case of re, use a powder re extinguisher, not a water one.
–Do not tamper with the machine safety guards and follow the ordinary maintenance instructions
scrupulously.
–Do not allow any object to enter into the openings. Do not use the machine if the openings are clogged.
Always keep the openings free from dust, hairs and any other foreign material which could reduce the air
ow.
–Do not remove or modify the plates afxed to the machine.
–This machine cannot be used on roads or public streets.
–Pay attention during machine transportation when temperature is below freezing point. The water in the
recovery tank or in the hoses could freeze and seriously damage the machine.
–Use brushes and pads supplied with the machine or those specied in the User Manual. Using other brushes
or pads could reduce safety.
–In case of machine malfunctions, ensure that these are not due to lack of maintenance. If necessary, request
assistance from the authorised personnel or from an authorised Service Center.
9099653000 - 07-2012.indb 5 24-Jul-12 15:17:39

ENGLISH INSTRUCTIONS FOR USE
6VANTAGE 17 E - 9099653000
WARNING!
–If the machine
• does not work properly
•is damaged
•has water or foam leaks
• has been left outdoors exposed to bad weather conditions
• is wet or has been dropped into water
turn it off immediately and contact the Clarke Service Center or a qualied technician.
–If parts must be replaced, require ORIGINAL spare parts from an Authorised Dealer or Retailer.
–To ensure machine proper and safe operation, the scheduled maintenance shown in the relevant chapter of
this Manual, must be performed by the authorised personnel or by an authorised Service Center.
–Do not wash the machine with direct or pressurised water jets, or with corrosive substances.
–The machine must be disposed of properly, because of the presence of toxic-harmful materials (electronic
components, etc.), which are subject to standards that require disposal in special centres (see the Scrapping
chapter).
120 VAC GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should electrically malfunction, grounding provides a path of least resistance for electric
current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and
grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all
local codes and ordinances.
WARNING!
The machine must be used with an extension power cord as follows:
–minimum length 15 feet
–type S, or ST, or SO, or STO, or STW
–minimum rate 300V 140/167°F (60/75°C)
DANGER!
–Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with
a qualied electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do
not modify the plug provided with the appliance. If it will not t the outlet, have a proper outlet installed by a
qualied electrician.
–This appliance is for use on a nominal 120V circuit, and has a grounding plug that looks like the plug (B, Fig.
1). A temporary adapter (B and C) may be used to connect this plug to a 2-pole receptacle (B), if a properly
grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet
(A) can be installed by a qualied electrician. The green-colored rigid ear, tab, or the like extending from the
adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever
the adapter is used, it must be held in place by a metal screw. Grounding adapters are not approved for use
in Canada.
–Replace the plug if the grounding pin is damaged or broken.
–The Green (or Green/Yellow) wire in the cord is the grounding wire. When replacing a plug, this wire must be
attached to the grounding pin only.
–Extension cords connected to this machine should be 12 gauge, three-wire cords with three-prong plugs and
outlets. DO NOT use extension cords more than 50 feet (15 m) long.
A B C
Figure 1
S310183A
9099653000 - 07-2012.indb 6 24-Jul-12 15:17:39

INSTRUCTIONS FOR USE ENGLISH
9099653000 - VANTAGE 17 E 7
13
14
14
15 11
25
17
16
26
21
22
12
1519
4
10
23
24
28
27
9820 13
7
51
6
18
23b23a
11
29 2
3
P100648
MACHINE DESCRIPTION
MACHINE STRUCTURE
1. Serial number plate/technical data/conformity certication
2. Handlebar
3. Control panel
4. Solution ow opening/closing valve
5. Solution solenoid valve
6. Recovery tank cover
7. Rear support wheel for transport/parking
8. Central wheels on xed axle
9. Brush/pad
10. Brush/pad-holder deck
11. Squeegee
12. Squeegee mounting handwheels
13. Front squeegee blade
14. Rear squeegee blade
15. Squeegee blade mounting springs
16. Recovery water drain hose
17. Recovery water drain hose bracket
18. Solution drain hose with level check marks
19. Squeegee lowering pedal
20. Solution lter
21. Power supply cable
22. Squeegee vacuum hose
23. Transport/parking wheel
23a. Transport/parking wheel (engaged)
23b. Transport/parking wheel (disengaged)
24. Transport/parking device positioning pin
25. Recovery water drain plug
26. Main switch
27. Recovery tank
28. Solution tank
29. Can holder
9099653000 - 07-2012.indb 7 24-Jul-12 15:17:40

ENGLISH INSTRUCTIONS FOR USE
8VANTAGE 17 E - 9099653000
31
32
42
36
41
34
46
33 35
37
43
38
39
40
44
45
P100649
MACHINE STRUCTURE (Continues)
31. Recovery water tank cover (open)
32. Recovery tank cover gasket
33. Front brush/pad-holder support
34. Recovery tank compartment
35. Solution tank ller neck
36. Vacuum grid with automatic shut-off oat
37. Safety rod for open cover
38. Vacuum system motor
39. Brush/pad-holder motor
40. Machine straight forward movement adjusting handwheel
41. Machine forward speed adjusting handwheel
42. Brush
43. Pad-holder
44. Pad
45. Brush rotation direction
46. Lifted squeegee
9099653000 - 07-2012.indb 8 24-Jul-12 15:17:42

INSTRUCTIONS FOR USE ENGLISH
9099653000 - VANTAGE 17 E 9
HANDLEBAR AND CONTROL PANEL
51. Brush enabling push-buttons
52. Brush/pad-holder activation switch
53. Vacuum system activation switch
54. Solution ow push-button Press to reach the desired
quantity, as shown by LEDs (55).
55. Solution ow quantity LED indicators:
– 1 LED on: Minimum solution ow.
– 2 LEDs on: Medium solution ow.
– 3 LEDs on: Maximum solution ow.
– LEDs off: Closed solution ow.
2 3
51 51
52 53 55 54
P100650
ACCESSORIES/OPTIONS
In addition to the standard components, the machine can be equipped with the following accessories/options, according to the
machine specic use:
– Brushes/pads of different materials
– Counterweight
For further information concerning the optional accessories, contact an authorised Retailer.
9099653000 - 07-2012.indb 9 24-Jul-12 15:17:43

ENGLISH INSTRUCTIONS FOR USE
10 VANTAGE 17 E - 9099653000
TECHNICAL DATA
Model Vantage 17 E
Solution tank capacity 8.2 US gal (31 liters)
Recovery tank capacity 7.9 US gal (30 liters)
Machine length 43.9 in (1,115 mm)
Machine width with squeegee 28.3 in (720 mm)
Machine width without squeegee 22.4 in (570 mm)
Machine height with adjustable handlebar 41.3 in (1,050 mm)
Counterweight (optional) 72.7 lb (33 kg)
Minimum turning radius 29.5 in (750 mm)
Cleaning width 17 in (430 mm)
Wheel diameter 9.8 in (250 mm)
Wheel pressure on the oor 188 psi (1.3 N/mm2)
Brush/pad diameter 17 in (430 - 432 mm)
Brush/pad pressure with full tank and lowered squeegee 106 lb (48 kg)
Min/max solution ow 0.1 / 0.42 gpm (0.4 / 1.6 liters/min)
Sound pressure level at workstation (ISO 11201, ISO 4871, EN 60335-2-72) (LpA) 74 dB(A) ± 3 dB(A)
Machine sound pressure level (ISO 3744, ISO 4871, EN 60335-2-72) (LwA) 91 dB(A)
Vibration level at the operator’s arms (ISO 5349-1, EN 60335-2-72) < 98.4 in/s2(< 2.5 m/s2)
Maximum gradient when working 2%
Protection class (IP) X4
Protection class (electric) I
Vacuum system motor power 0.73 hp (550 W)
Vacuuming 0.0127 MPa (1,300 mmH2O)
Brush/pad motor power 0.73 hp (550 W)
Brush/pad-holder motor speed 180 rpm
Electrical system voltage 115 V - 60 Hz
Total absorbed power 10 A (1.1 kW)
Weight with empty tanks 143 lb (65 kg)
Gross vehicle weight (GVW) 278 lb (126 kg)
Shipping weight 216 lb (98 kg)
9099653000 - 07-2012.indb 10 24-Jul-12 15:17:43

INSTRUCTIONS FOR USE ENGLISH
9099653000 - VANTAGE 17 E 11
WIRING DIAGRAM
Key
EB1 Control panel electronic board
EBLED LED electronic board
EV1 Detergent solenoid valve
F1 Signal circuit fuse
LDA Green LED
LDB Green/yellow LED
LDC Green/red LED
M1 Brush motor
M2 Vacuum system motor
SW0 Main switch
SW1 Brush switch
SW2 Vacuum system switch
SW3 Detergent rate switch
SW4,5 Brush enabling switch
Color codes
BK Black
BU Blue
BN Brown
GN Green
GY Grey
OG Orange
PK Pink
RD Red
VT Violet
WH White
YE Yellow
P100657
GROUNDING CONNECTION
(See Fig. 2)
A) Grounding pin
B) Grounded outlet
C) Grounded outlet box
D) Adapter
E) Metal screw
F) Adapter
G) Grounding screw tab
A
B
C
D
E
F
G
Figure 2
S310183B
9099653000 - 07-2012.indb 11 24-Jul-12 15:17:43

ENGLISH INSTRUCTIONS FOR USE
12 VANTAGE 17 E - 9099653000
USE
WARNING!
On some points of the machine there are some adhesive plates indicating:
–DANGER
–WARNING
–CAUTION
–CONSULTATION
While reading this Manual, the operator must pay particular attention to the symbols shown on the plates (see Visible Symbols On
The Machine paragraph).
Do not cover these plates for any reason and immediately replace them if damaged.
BEFORE MACHINE START-UP
Brush or pad-holder installation
NOTE
Use either the brush (42) or the pad-holder (43 and 44) according to the type of oor to be cleaned.
1. Insert the positioning pin (24) and disengage the machine transport/parking device (23b).
2. Lift the brush/pad-holder deck (10) by prying the handlebar (2).
3. Place the brush (42) or the pad-holder (43 and 44) under the deck.
4. Lower the deck (10) by using the handlebar (2).
5. Connect the power supply plug (21) to the electrical mains.
6. Turn the switch (52) to “I”.
7. Press the brush enabling push-buttons (51) to engage the brush/pad-holder to the deck hub (10). If necessary, repeat the
procedure until the brush/pad-holder is engaged.
Available brushes and their relevant application guides (suggestions only)
Models MIDLITE GRIT 180 MIDGRIT 240 PROLITE UNION MIX
General cleaning
Concrete
Terrazzo oor
Ceramic tiles/quarrystones
Marble
Vinyl tiles
Rubber tiles
Polishing
Rubber tiles
Marble
Vinyl tiles
Squeegee installation
8. Install the squeegee (11) and fasten it with the handwheels (12), then connect the vacuum hose (22) to the squeegee.
Solution tank lling
CAUTION!
Use only low-foam and non-ammable detergents, intended for automatic scrubber applications.
WARNING!
When using oor cleaning detergents, follow the instructions on the labels of the detergent bottles.
To handle oor cleaning detergents, wear suitable gloves and protections.
9. Use the ller neck (35) to ll the tank (28) with a solution suitable for the work to be performed. Do not ll the solution tank
completely, leave few inches from the edge. Always follow the dilution instructions on the label of the chemical product used to
prepare the solution. The solution temperature must not exceed 104 °F (40 °C).
9099653000 - 07-2012.indb 12 24-Jul-12 15:17:43

INSTRUCTIONS FOR USE ENGLISH
9099653000 - VANTAGE 17 E 13
MACHINE START AND STOP
Starting the machine
1. Prepare the machine as shown in the previous paragraph.
2. Drive the machine to the working place by pushing it with the hands on the handlebar (2).
3. Connect the power supply plug (21) to the electrical mains.
WARNING!
Before connecting the power supply plug to the electrical mains, check that frequency and voltage, shown on
the machine serial number plate (1), match the electrical mains voltage.
4. To turn on the machine, turn the main switch (26) to “I”.
5. Lower the squeegee (11) with the pedal (19).
6. Turn the main switch (52) to “I”, to turn on the brush motor.
7. Turn the switch (53) to “I”, to turn on the vacuum system motor.
8. Press the solution ow push-button (54) to change the solution quantity. Green LEDs (55) indicate the ow quantity according
to the following table:
LEDs on (55)
Setting Minimum solution ow. Medium solution ow. Maximum solution ow. Closed solution ow.
9. To start scrubbing/drying, keep the hands on the handlebar (2) and start the machine by pressing the brush enabling push-
buttons (51).
Stopping the machine
10. Release the brush enabling push-buttons (51).
11. Turn the switch (53) to “0”, to turn off the vacuum system motor.
12. Turn the switch (52) to “0”, to turn off the brush motor.
13. To turn off the machine, turn the main switch (26) to “0”.
14. Disconnect the power supply cable plug (21) from the electrical mains and place it on the holder.
15. Engage the positioning pin (24) and activate the machine transport/parking device (23a) to keep the brush/pad-holder lifted
(see Fig. 3).
16. Make sure that the machine cannot move independently.
NOTE
Each time that the machine is turned off, the solution ow program turns automatically to minimum level, to reduce water
consumption.
9099653000 - 07-2012.indb 13 24-Jul-12 15:17:44

ENGLISH INSTRUCTIONS FOR USE
14 VANTAGE 17 E - 9099653000
Squeegee lifting
Lift the squeegee as indicated below:
1. Grasp the handlebar (2), lower it until the rear wheel (7)
touches the oor (A, Fig. 3) then engage the squeegee in
lifted position (B).
A
B
clik
Figure 3
P100642
MACHINE OPERATION (SCRUBBING/DRYING)
1. Start the machine as shown in the previous paragraph.
2. While keeping both hands on the handlebar (2), move the machine and start scrubbing/drying the oor.
3. If necessary, adjust the solution quantity by using the push-button (54).
CAUTION!
To avoid damaging the oor surface, do not use the brush without the solution and, when the machine is not
operating, stop the brush/pad-holder by releasing the push-buttons (51).
CAUTION!
Before lifting the brush/pad, turn it off by releasing the push-buttons (51).
NOTE
For correct scrubbing/drying of oors at the sides of the walls, Clarke suggests to go near the walls with the right side of
the machine as shown in gure 4.
A
A
B
Figure 4
P100643
Machine speed adjustment
4. The machine speed varies according to the type of oor to be cleaned and the choice of using the brush or the pad. If
necessary, it is possible to adjust the machine speed, according to the procedure shown in Maintenance chapter.
9099653000 - 07-2012.indb 14 24-Jul-12 15:17:45

INSTRUCTIONS FOR USE ENGLISH
9099653000 - VANTAGE 17 E 15
MACHINE TRANSPORT/PARKING
To transport/park the machine, proceed as follows.
1. To turn off the machine, turn the main switch (26) to “0”.
2. Disconnect the power supply cable plug (21) from the electrical mains and place it on the holder.
3. Lift the squeegee (46).
4. Engage the positioning pin (24) and activate the machine transport/parking device (23a) to keep the brush/pad-holder lifted
(Fig. 5).
5. While holding the machine in this position, drive it to the transport/parking area.
6. In order not to drag the brush/pad on the oor and leave wet marks, when nishing working, remove the brush/pad-holder from
the deck by using the disengagement procedure (see the next paragraph), then place it on the front holder (33).
Figure 5
P100644
Brush/pad-holder removal
Remove the brush/pad-holder deck by performing the following procedure:
1. Connect the power supply plug (21) to the electrical mains.
2. To turn on the machine, turn the main switch (26) to “I”.
3. Turn the switch (52) to “I”.
4. Lift the brush/pad-holder deck (10) by prying the handlebar (2).
5. Press the push-buttons (51) 3 times consequently, then wait that the brush starts and stop, thus disengaging from the drive
hub.
6. Turn the switch (52) to “0”.
7. To turn off the machine, turn the main switch (26) to “0”.
8. Disconnect the power supply cable plug (21) from the electrical mains and place it on the holder.
TANK EMPTYING
An automatic oat shut-off system (36) turns off the vacuum system when the recovery tank (27) is full.
The vacuum system shutdown, due to the recovery tank lling, is signalled by an increase in the vacuum system motor noise,
moreover the oor is not dried.
CAUTION!
If the vacuum system turns off accidentally (for example, when the oat is activated because of a sudden
machine movement), to resume the operation: turn off the vacuum system by turning the switch (53) to “0”, then
open the recovery tank cover (31) and check that the oat inside the grid (36) has gone down to the water level.
Then close the recovery tank cover (6) and turn on the vacuum system by turning the switch (53) to “I” position.
When the recovery tank (27) is full, empty it according to the following procedure.
9099653000 - 07-2012.indb 15 24-Jul-12 15:17:46

ENGLISH INSTRUCTIONS FOR USE
16 VANTAGE 17 E - 9099653000
Recovery tank emptying
1. To turn off the machine, turn the main switch (26) to “0”.
2. Disconnect the power supply cable plug (21) from the electrical mains and place it on the holder.
3. Lift the squeegee (46).
4. Drive the machine to the appointed disposal area.
5. Insert the positioning pin (24) and lift the brush/pad-holder by engaging the transport/parking device (23a).
6. Empty the recovery tank (27) with the drain hose (16). Then, rinse the tank with clean water.
Solution tank emptying
Perform steps 1 to 4.
7. Empty the solution tank (28) with the hose (18).
8. Then, rinse the tank with clean water.
AFTER USING THE MACHINE
After working, before leaving the machine:
1. Remove the brush/pad-holder as shown in the Machine
Transport/Parking paragraph.
2. Disconnect the power supply cable plug (21) from the
electrical mains and place it on the holder.
3. Empty the tanks (27 and 28) as shown in the previous
paragraph.
4. Perform the daily maintenance procedures (see the
Maintenance chapter).
5. Store the machine in a clean and dry place, with the brush/
pad-holder and the squeegee lifted or removed.
RECOVERY TANK REMOVAL
To perform check and maintenance procedures, it may be
necessary to remove the recovery tank (27) as shown below.
1. Empty the recovery tank (27) as shown in the relevant
paragraph.
2. Drive the machine on a level oor.
3. Make sure that the power supply cable plug (21) is
disconnected from the electrical mains.
4. Disconnect the vacuum hose (22) from the squeegee (11).
5. Disconnect the recovery water drain hose (16) from the
bracket (17).
6. Open the cover (6).
7. Grasp the recovery tank (A, Fig. 6) in the area (B) and
slightly raise it.
8. Disconnect the vacuum hose (C) from the tank, then
remove the tank (A) with the hoses (D) and (E).
BA
C
D
E
Figure 6
P100641
MACHINE LONG INACTIVITY
If the machine is not going to be used for more than 30 days, proceed as follows:
1. Perform the procedures shown in After Using the Machine paragraph.
2. Store the machine in a clean and dry place.
FIRST PERIOD OF USE
After the rst 8 hours, check the machine fastening and connecting parts for proper tightening. Check the visible parts for integrity
and leakage.
9099653000 - 07-2012.indb 16 24-Jul-12 15:17:47

INSTRUCTIONS FOR USE ENGLISH
9099653000 - VANTAGE 17 E 17
MAINTENANCE
The lifespan of the machine and its maximum operating safety are ensured by correct and regular maintenance.
The following chart provides the scheduled maintenance. The intervals shown may vary according to particular working conditions,
which are to be dened by the person in charge of the maintenance.
WARNING!
Maintenance procedures must be performed with the machine switched off and the power supply cable plug
disconnected from the electrical mains.
Moreover, carefully read the instructions in the Safety chapter.
All scheduled or extraordinary maintenance procedures must be performed by qualied personnel, or by an authorised Service
Center.
This Manual describes only the easier and most common maintenance procedures.
NOTE
For other maintenance procedures shown in the Scheduled Maintenance Table, refer to the Service Manual that can be
consulted at any Service Center.
SCHEDULED MAINTENANCE TABLE
Procedure
Daily, after
using the
machine
Weekly Every six
months Yearly
Squeegee cleaning
Brush cleaning
Tank and vacuum grid cleaning
Power supply cable check
Squeegee blade check and replacement
Solution lter cleaning
Screw and nut tightening check (1)
Vacuum system motor carbon brush check and replacement (2)
(1) And after the rst 8 working hours.
(2) This maintenance procedure must be performed by an authorised Clarke Service Center.
9099653000 - 07-2012.indb 17 24-Jul-12 15:17:47

ENGLISH INSTRUCTIONS FOR USE
18 VANTAGE 17 E - 9099653000
SQUEEGEE CLEANING
NOTE
The squeegee must be clean and its blades must be in good conditions in order to get a good drying.
WARNING!
It is advisable to wear protective gloves when cleaning the squeegee because there may be sharp debris.
1. Drive the machine on a level oor.
2. Make sure that the power supply cable plug (21) is disconnected from the electrical mains.
3. Lower the squeegee with the pedal (19).
4. Disconnect the vacuum hose (22) from the squeegee.
5. Loosen the handwheels (12) and remove the squeegee (11).
6. Wash and clean the squeegee. In particular, clean the compartments (A, Fig. 7) and the vacuum hole (B) from dirt and debris.
7. Check the front blade (C) and the rear blade (D) for integrity, cuts and tears; if necessary replace them (see the procedure in
the following paragraph).
8. Assemble the components in the reverse order of disassembly.
SQUEEGEE BLADE CHECK AND REPLACEMENT
1. Clean the squeegee as shown in the previous paragraph.
2. Check that the front blade edges (E, Fig. 7) and the rear blade edges (I) lay down on the same level, along their length; if
necessary adjust the height according to the following procedure:
• Remove the mounting springs (F), then adjust the front blade (C) and the rear blade (D).
• Install the mounting springs on the front and rear blades.
3. Check the front blade (C) and rear blade (D) for integrity, cuts and tears; if necessary replace them as shown below. Also
check the front corner (H) of the rear blade for wear; if it is worn, overturn the blade to replace the worn corner with the other
one (G), if it is integral. If the other corner is worn too, replace the blade according to the following procedure:
• Remove the mounting springs (F) and then replace (or overturn) the rear blade (D).
• Install the mounting springs on the front and rear blades.
4. Install the squeegee (11) and screw tighten the handwheels (12).
5. Connect the vacuum hose (22) to the squeegee (11).
E H IG
A
B
A
D
F
F
C
Figure 7
P100629
9099653000 - 07-2012.indb 18 24-Jul-12 15:17:47