Clarke VAC KING CVAC20SS Installation and operation manual

OPERATING & MAINTENANCE
INSTRUCTIONS
MODEL Nos:
CVAC20SS•CVAC25SS• CVAC30SSR
Distributed by CLARKE International Ltd. 1006

Thank you for selecting this VAC KING Stainless Steel Vacuum Cleaner, which will
provide you with a cleaner and safer working environment.
This machine is capable of collecting both wet and dry materials as well as water.
DO NOT, however, collect any other type of liquid as this could be dangerous.
Before attempting to use this machine, please read this leaflet thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to this Vacuum Cleaner
giving you long and satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12 months from
the date of purchase. Please keep your receipt therefore, as proof of purchase.
This guarantee is invalid if the product is found to have been abused or tampered
with in any way, or not used for the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product can be
returned to us without prior permission.
This guarantee does not effect your statutory rights.
SAFETY PRECAUTIONS
1. Do not allow the VAC to run unattended.
2. Do not use with accessories other than those provided.
3. Do not use if the electric cable, plug, motor filter or the cleaner itself, is in poor
condition.
4. Do not attempt any electrical repair yourself. Consult a qualified electrician,
or our Service Department on 020 8988 7400
5. Do not pick up flammable or readily combustible material, hot ashes, coals,
or use in the presence of explosive liquids or vapour.
6. Do not use in enclosed areas where flammable, explosive or toxic vapours
are given off, by oil based paints, paint thinner, petrol etc.
7. Do not pick up burning cigarettes or other smoking substances.
8. When you have finished with the machine, ensure the electric cable is stowed
away and not left as a hazard, i.e. for others to trip over.
9. Do not change filters, or carry out any cleaning or servicing, without first
disconnecting the machine from the mains supply.
10. Do not pull the machine along by the electric cable, or pull the cable to
disconnect the plug from the mains socket. Keep the electric cable away
from heat , oil and sharp edges. Do not close doors on the cable, or allow it to
become snagged under furniture or objects with sharp edges.
11. If this machine is used outdoors, on no account must it be exposed to rain.
Ensure it is stored indoors.
- 2 -

This machine must be wired up in accordance with the following colour code:
BLUE - NEUTRAL
BROWN - LIVE
•Connect the BLUE coloured cord to the plug terminal marked “N”
•Connect the BROWN coloured cord to the plug terminal marked “L”
If this appliance is fitted with a plug which is moulded on to
the electric cable (i.e. non-rewireable) please note:
1. The plug must be thrown away if it is cut from the
electric cable. There is a danger of electric shock if it
is subsequently inserted into a socket outlet.
2. Never use the plug without the fuse cover fitted.
Fuse Rating
The fuse in the plug must be replaced with one of the same rating (13 amps) and this
replacement must be approved to BS1362.
If in doubt, consult a qualified electrician. Do not attempt any electrical repairs yourself.
Cable Extension
Always use an approved cable extension suitable for the power rating of this tool (see
specifications), the conductor size should also be at least the same size as that on the
machine, or larger. When using a cable reel, always unwind the cable completely.
3. Should you wish to replace a detachable fuse carrier, ensure that the correct
replacement is used (as indicated by marking or colour code).
4. Replacement fuse covers can be obtained from your local dealer or most electrical
stockists.
IMPORTANT:
If a cable extension is needed, it is essential to comply with the following data.
Voltage Extension length Cable section
230v Up to 20m 2.5mm2
230v From 20 to 50m 4mm2
This product is provided with a standard 13 amp, 230 volt (50Hz), BS 1363 plug, for
connection to a standard, domestic electrical supply. Should the plug need changing at
any time, ensure that a plug of identical specification is used.
ELECTRICAL CONNECTIONS
WARNING ! THIS APPLIANCE IS DOUBLE INSULATED
- 3 -

PREPARATION FOR USE
PRERARATION FOR USE
Fig.1
This is an illustration
showing the CVAC20P,
however all other
models have similar
components but
may differ slightly
in design.
1. Motor & Head section
2. Container
3. Flexible Hose
4. Extension Tube
5. Brush Adapter
6. Hose/Extension Tube Angle Adapter
7. Crevice Tool
8. Power Tool Adapter (CVAC30SSR only)
9. Casters
10. Cartridge Filter
11. Paper Dust bag.
12. Foam Filter (for water Pick-up 0nly)
- 4 -

- 5 -
With the VAC King removed from the packaging, undo the two clamps securing
the head and remove the components from within the tank. Lay them out and
check to ensure that no damage was suffered in transit.
For ease of mobility, all models are mounted on bases provided with castors. These
rare simply pushed into their mountings firmly.
THE FILTERS
NOTE: Filters are essential to ensure that dust or foreign matter does not enter the
motor compartment which would reduce motor efficiency, and eventually cause
serious damage.
Four filters are supplied with the machine.
1. All Models are provided with a Cartridge
filter. This is the primary filter, and must be fitted
over the filter cage, used for dry vacuuming
ONLY.
2. The Paper Bag Filter is the secondary filter and
should be used at all times for dry vacuuming
ONLY.
3. The Foam filter. This is only used for picking up
water, and replaces the Cartridge filter, and
Paper Bag, during this operation.
Cartridge filter
Paper Bag Filter
Foam Filter
IMPORTANT: This double filtering action not only ensures that the motor is
kept dirt free, but is essential in ensuring that the cleanest air possible is
exhausted, therefore preventing dust from being spread into the environment.

- 6 -
OPERATION
• Before plugging in to the mains supply, open the machine and check to ensure
the appropriate filters are securely in place, and are in good condition. If the
paper bag is full...replace it.
• REMEMBER, to use the FOAM FILTER ONLY for picking up WATER, and ensure
that it is correctly fitted, so that it covers the filter cage completely.
NOTE: Be aware that when picking up water, the tank will gradually fill up. Check
and empty at frequent intervals, otherwise the float located within the filter unit
will rise and eventually shut off suction. This is a safety feature to prevent water
from coming into contact with electrical components.
Should suction cease, you will hear a more urgent sound from the motor. Switch
OFF immediately and empty the tank, otherwise the motor could overheat.
• Switch the machine ON and proceed to use as normal.
Dust Extraction - CVAC30SSR ONLY
This machine is provided with a standard three pin auxiliary power take off. This
allows the machine to be used as a dust extraction device for power tools, so that
when the power tool is switched ON, the CVAC will automatically start. When the
power tool is switched OFF, the CVAC will switch itself OFF after a short delay.
NOTE: In the Dust extraction mode, the main ON/OFF switch AND the Power Take-
Off switch must be switched ON. Switch ON the power take off switch first.
Additionally, a rubber stepped adapter is provided which may be pushed into the dust
extraction port of the power tool and on to which the flexible hose may be attached.
IMPORTANT: On no account must this mode be used when picking up water.
MAINTENANCE
Maintenance is limited to inspecting the filters regularly, and replacing when
necessary.
The cartridge filter is of paper construction and may not therefore be washed. It
may be brushed clean and compressed air at low pressure may also be used if
necessary. If either of the filters become holed or damaged in any way, they must
be replaced.
Also ensure that the hose is kept in good condition. A damaged hose will seriously
effect the efficiency of the machine, and should be replaced immediately.
Inspect all other components periodically, and replace damaged castors or
accessories when necessary. Contact your CLARKE dealer for replacements.
Regular inspection and the correct maintenance of the filters, will ensure the
efficient running and prolong the life of your machine.

- 7 -
SPECIFICATIONS
CVAC20SS CVAC25SS CVAC30SSR
Motor - Power Rating ................ 1.4kW ................. 1.4kW ................. 1.4kW
Voltage .................. 230V 50Hz 1Ph ... 230V 50Hz 1Ph ... 230V 50Hz 1Ph
IP Rating ........................... 24 ....................... 24 ....................... 24
Insulation Rating ............... E ......................... E ......................... E
Duty Cycle ........................... S1 (Continuous) .. S1 (Continuous) . S1 (Continuous)
Tank Capacity - water .............. 14Litres ............... 19Litres ............... 23Litres
Dust Capacity ........................... 16Litres ............... 21Litres ............... 26Litres
Max. Vacuum ............................. 15kPa ............... 15.5kPa ............... 16kPa
Sound Pressure Level (at 2M) .. 82dB(A) ............. 82dB(A) ............. 82dB(A)
Power Cable Length ..................... 4M ..................... 4M ..................... 4M
Dimensions (MM) .................. 470X470X556 ..... 470X470X630 ..... 515x515x635
Weight ........................................ 6.5kg ................... 7kg ................... 8.5kg
Part No. ..................................... 6471105 ............. 6471110 ............. 6471120
SPARE PARTS / ACCESSORIES
Description CVAC20SS CVAC25SS CVAC30SSR
Part No. Part No. Part No.
Paper Dust bag HT90605 HT90609 HT90602
Foam Filter HT90503 HT90503 HT90503
Cartridge Filter HT90501 HT90501 HT90501
Casters HTTVQTJC0400 HTTVQTJC0400 HTTVQTJC0400
Flexible Hose 2.5M HT80819 HT80819 HT80819
Angle Adapter (Hose to Tube) HT80401 HT80401 HT80401
Metallic Telescopic Tube HT80905 HT80905 HT80905
Combi Brush Tool HT80701 HT80701 HT80701
Crevice Tool HT80707 HT80707 HT80707
Power Tool Adapter - - HT80302