Classic Exhibits Visionary Designs LTK-1109 User manual

www.classicexhibits.com
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - LTK-1109 - Counter Assembly
Plex Shelf
Counter Top
Screw
Cap
Shelf
Infill
Infill
Infill
Infill
Infill
Infill
1
2
3
4
5
5
5
5
6
6
7
7
8
8
8
8
Item
1
2
3
4
5
6
7
8
Qty.
1
1
1
1
4
2
2
4
Description
41.5” RSG540 Vertical Extrusion
41.5” RSG540 Vertical Extrusion
35.5” RSG540 Vertical Extrusion
35.5” RSG540 Vertical Extrusion
16” Z45 Horizontal Extrusion
42.9” Z45 Curved Horizontal Extrusion
34.9” Z45 Curved Horizontal Extrusion
37.9” Z45 Vertical Extrusion
Steps:
1) Assemble front panel by locking 3 verticals [8]
to lower curved horizontal [6], insert infills, and
lock in place with upper curved horizontal [6].
2) Connect verticals [1,4] and [2,3] with horizontals
[5], inserting infills as shown.
3) Connect assembled sides [1/4] and [2/3] with
assembled front panel, locking curved horizontals
[6] to verticals [1,2].
4) Connect verticals [3,4] with lower curved horizontal
[7] as shown.
5) Lock vertical [8] to lower curved horizontal [7], insert
infills, and lock in place with upper curved horizontal
[7] as shown.
6) Attach shelf supports to velcro on inside of verticals [1-4].
7) Place shelf on shelf supports.
8) Slide counter top over front verticals [1,2] and secure Plex
shelf to verticals with screw caps.
9) Attach literture racks as desired.
Shelf
Support
Attach connector piece to rack
as shown. Then connect
assembled literature
rack to vertical extrusion.
Literature Rack Attachment
Tighten Lock
to Secure
All manuals and user guides at all-guidesbox.com
all-guidesbox.com

www.classicexhibits.com
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews
All manuals and user guides at all-guidesbox.com

www.classicexhibits.com
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -Case Packing Instructions
Top View
Level 1 Level 2 Level 3 Level 4 Level 5 Level 6
Setup Hardware
Counter
Top
Shelf Infills
8 (4x)
Plex
Shelf
7,7
6,6
Assembled
Side
Assembled
Side
All manuals and user guides at all-guidesbox.com