Classic Exhibits euro lt LTK-1121 Instruction manual

www.classicexhibits.com
866.652.2100
© 2012
Order #xxxxx - LTK-1121 -
Page 1 of 1
Pedestal Assembly
Door
Item Number
1
2
3
4
5
6
7
8
9
10
Description
14.125”w x 38”h Flat Panel w/ Door
14.125”w x 38”h Flat Panel w/ Door
38”h 90° Connector
15.88”w x 38”h Flat Panel
38”h 90° Connector
14.125”w x 38”h Flat Panel
14.125”w x 38”h Flat Panel
38”h 90° Connector
15.88”w x 38”h Flat Panel
38”h 90° Connector
123
4
5
6
7
8
Steps:
Connect panels together in numerical order
as shown in illustrations.
Set counter atop assembled pedestal.
Door
Counter Top
Internal Shelf
Velcro shelf support
to inside of assembled
base as indicated.
Upper Counter Top
Cap
Standoff
Barrel
Set standoff barrels on
Lower Counter Top, place
Upper Counter Top
and secure standoff barrles
by twisting as shown.
Standoff Assembly
Counter Top
9
10

www.classicexhibits.com
866.652.2100
© 2012
Order #xxxxx - LTK-1121 -
Page 2 of 1
General Insructions
Using Your Setup Instructions
Cleaning and Packing Your Display
The Euro LT Hybrids Setup Instructions are created specifically for your configuration.
They are laid out sequentially in levels, including exploded views, and a logical series of detailed steps
to assemble the main structure and components. We encourage you to study the instructions before
attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your exhibit to prevent loss of the
locks and setscrews (see below in RED). This is VERY IMPORTANT.
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) When cleaning laminate inserts, countertops, or panels use mild cleansers and a soft material
such as cotton.
3) Keep all display components away from extreme heat and long exposure to sunlight to avoid
warping and fading.
4) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
Each component has 2 clips,
the lower clip is ALWAYS
black. The top clip is color
coded to distinguish which
level. The color coded clip
also contains the numbered
label.
Connector
Level 1 = Blue
Level 2 = Red
Level 3 = Green
Level 4 = Black
Panel Lock
When Required
Color Coded Clip
w/ assembly number
Black Clip
is bottom of
panel
L
e
f
t
P
a
n
e
l
R
i
g
h
t
P
a
n
e
l
Cut Away View of
Slide Clips
Components connect together
by aligning them and sliding
downward connecting clips
together.
Configurations are assembled
from left to right, usually
starting with #1 and following
the numbered sequence.
Example of Connection Top View of Panels with Locks
The first level of components contain
panel locks that are located at the top of
the panel for extra stability and seamless
connection. When disassembling panels
twist top connection slightly and lift right
panel upward.
Panel Lock
When Required
Color Coded Clip
w/ assembly number
is top of panel
Left Hand
Grasps Panel
Firmly
With Right Hand Thumb
Close to Seam
Squeeze,
Push Forward,
And Lift
General Setup Instructions for Extrusion System
The Tool Typical Connection Typical Connection (cont’d) Numbered Label
Most exhibits can be assembled
with the supplied Hex Key Tool.
Occasionally, a flat head screw-
driver may be required.
Most horizontal extrusion connections have a patented expandable
lock. This lock inserts into the groove of an opposing extrusion.
Tightening the lock with the Hex Key Tool expands the lock and
creates a strong positive connection.
Each extrusion contains a numbered
label which corresponds with setup
instructions. The label is located
within a groove of the extrusion
(when possible). With extrusion
components the labels contain
Black numbers unless otherwise
specified.
Detail A Detail B Detail C
Horizontal Inline Connection (remove only one setscrew) Base Plate Connection Vertical Connection
(remove only two setscrews)
Detail D Detail E
Setscrews
Remove only (1) setscrew when disassembling.
Replace setscrew in extrusion after assembling
it. Before packing, replace setscrew in extrusion
to avoid losing it.
Attach base plate to round or
square vertical extrusion using
the bolt provided. Be careful
not to strip the threads.
When vertical extrusions are
packed in portable cases rather
than crates or tubs, they must be
broken down into smaller sections
which then require assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews
in extrusion after assembling it.
Before packing, replace setscrews
in extrusion to avoid losing them.

www.classicexhibits.com
866.652.2100
© 2012
Order #xxxxx - LTK-1121 -
Page 3 of 1
Case Packing Instruction
Counter Top
Setup Hardware Box
Counter Top
Internal Shelf
1
2
3
8
7
5
6
4
Case
9
10