Classic Exhibits SEGUE DESIGN VK-2320 Manual

© 2024
Locked layer contains
placeholder marks.
Plan View
10’
20’
VK-2320 - 10’ x 20’ Segue Inline
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2024
Locked layer contains
placeholder marks.
= 1 sq foot
Plan View

© 2024
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2024
Straight Connection
All knobs must be tightened securely to ensure a proper connection.
All knobs must be tightened securely to ensure a proper connection.
Adjust connectors if necessary to
prevent gaps in connection.
Upper Horizontal Extrusion
Lower Horizontal Extrusion
Straight Connector
Straight Connector
Corner
Connectors Corner
Connectors
Corner
Connectors Corner
Connectors
COMPLETED ASSEMBLY
3) Tighten all knobs to secure connection.
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
When assembling frame, first attach all straight
connectors, then attach corner connectors.
1) Place extrusions end-to-end.
2) Loosen all knobs, then slide straight
connectors across the seam of extrusions.
Disassembly
1) Loosen all knobs.
2) Slide connectors off of one extrusion.
3) Tighten knobs to prevent loss during
packing & shipping.
CEI110 Profile
Slide both connectors across seam of extrusions.
Tighten all knobs.
Corner Connection
3) Tighten all knobs to secure connection.
Disassembly
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
Keep straight connectors in groove of
extrusion. Do not remove connectors
during disassembly.
CEI110 Frame Assembly

© 2024
LT Panel Assembly
1) With a vertical offset, place LT-Panels side-by-side;
slide vertically offset panel down to lock panels
together and in place.
2) Corner Connectors (90°, T-Connector, Straight Connector)
connect just as panels connect together. Repeat Step 1
for installing corner connectors to panels.
LT Panel Disassembly
1) To disassemble push panel with upper locks horizontally
to disengage top lock clip.
2) Slide panels or connectors vertically in opposing directions
to release latches and disconnect parts.
While pushed in,
pull panel up to
disassemble
Push Panel in to
disengage the lock.
LT Panel Assembly

© 2024
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Installation

© 2024
Case 1 of 6
Locked layer contains
placeholder marks.
Top View of Each Level
Level 1
(Bottom level)
Level 2
1 2
Setup Hardware
20 21
VK-2320 Backwall
Case Packing

© 2024
Case 2 of 6
Locked layer contains
placeholder marks.
Top View of Each Level
Level 1
(Bottom level)
Level 2
3 4 5 9
Lights
VK-2320 Backwall
Case Packing

© 2024
Case 3 of 6
Locked layer contains
placeholder marks.
Top View of Each Level
Level 1
(Bottom level)
Level 2
6 7
1410
Monitor
Mount
VK-2320 Backwall
Case Packing

© 2024
Case 4 of 6
Locked layer contains
placeholder marks.
Top View of Each Level
12
811 13
Level 1
(Bottom level)
Level 2
VK-2320 Backwall
Case Packing