Classic Exhibits Euro LT Hybrids MOD-1533 User manual

www.classicexhibits.com
Step 1
Page 1 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - MOD-1533
When assembled
Front Graphic
Panel
Standoff
Cap
Side Panel
Vertical Channel
Front Graphic Attachment Detail
*
*
*
*
*
*
*
Top
Base
Shelf
Graphic Panel
Center Panel
Side Panel
Side Panel
Steps:
1) Attach Side Panels to Base with screws as shown.
2) Insert Center Panel into vertical channels
of Side Panels.
3) Attach Graphic Panel to curved Side Panels
with standoffs as shown.
4) Place shelf into Pedestal.
5) Place Pedestal Top onto top of assembled Pedestal
(see Counter Top Lock Detail).
Vertical
Channel
Place countertop
onto frame
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Lock Detail
Hole for lock
1 2
3 4
- Podium Assembly
Euro LT Hybrids General Setup Instructions
Using Your Setup Instructions
The Euro LT Hybrid Setup Instructions are created specifically for your configuration.
They are laid out sequentially in levels, including exploded views, and a logical series of
detailed steps to assemble the main structure and components. We encourage you to study
the instructions before attempting to assemble your exhibit.
Cleaning and Packing Your Display
1) When cleaning laminate countertops or panels use mild cleansers and a soft material such
as cotton.
2) Keep all display components away from extreme heat and long exposure to sunlight to avoid
warping and fading.
3) Retain all packing material. It will make re-packing much easier and will reduce the likelihood of
shipping damage.
Cut Away View Of
Slide Clips
Left
Panel
Right
Panel
Left Hand
Grasps Panel
Firmly
With Right Hand Thumb
Close to Seam
Squeeze,
Push Forward,
And Lift
Color Coded Clip
w/ assembly number
Panel Lock
When Required
Black Clip
is bottom of
panel
Connector Top View of Panel with Locks
Example of Connection
Color Coded Clip
w/ assembly number
Panel Lock
When Required
Each component has 2 clips,
the lower clip is ALWAYS
black.
Components connect together
by aligning them and sliding
downward connecting clips
together.
Configurations are assembled
from left to right, usually
starting with #1 and following
the numbered sequence.
The first level of components contains panel locks
that are located at the top of the panel for extra
stability and a seamless connection. When dis-
assembling panels, twist top connection slightly
and lift right panel upward.
Level 1 = Blue
Level 2 = Red
Level 3 = Green
Level 4 = Black
Top View of Panel with Locks
Color Code
The top clip is color
coded to distinguish the
level. The color coded clip
also contains the numbered
label.

www.classicexhibits.com
Step 2
Page 2 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - MOD-1533 - General Information
Euro LT Hybrids General Setup Instructions
Using Your Setup Instructions
The Euro LT Hybrid Setup Instructions are created specifically for your configuration.
They are laid out sequentially in levels, including exploded views, and a logical series of
detailed steps to assemble the main structure and components. We encourage you to study
the instructions before attempting to assemble your exhibit.
Cleaning and Packing Your Display
1) When cleaning laminate countertops or panels use mild cleansers and a soft material such
as cotton.
2) Keep all display components away from extreme heat and long exposure to sunlight to avoid
warping and fading.
3) Retain all packing material. It will make re-packing much easier and will reduce the likelihood of
shipping damage.
Cut Away View Of
Slide Clips
Left
Panel
Right
Panel
Left Hand
Grasps Panel
Firmly
With Right Hand Thumb
Close to Seam
Squeeze,
Push Forward,
And Lift
Color Coded Clip
w/ assembly number
Panel Lock
When Required
Black Clip
is bottom of
panel
Connector Top View of Panel with Locks
Example of Connection
Color Coded Clip
w/ assembly number
Panel Lock
When Required
Each component has 2 clips,
the lower clip is ALWAYS
black.
Components connect together
by aligning them and sliding
downward connecting clips
together.
Configurations are assembled
from left to right, usually
starting with #1 and following
the numbered sequence.
The first level of components contains panel locks
that are located at the top of the panel for extra
stability and a seamless connection. When dis-
assembling panels, twist top connection slightly
and lift right panel upward.
Level 1 = Blue
Level 2 = Red
Level 3 = Green
Level 4 = Black
Top View of Panel with Locks
Color Code
The top clip is color
coded to distinguish the
level. The color coded clip
also contains the numbered
label.

www.classicexhibits.com
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - MOD 1533
BASE CENTER
PANEL
FRONT
GRAPHIC SIDE SIDE
TOP
SHELF
CASE PACKING
Top Views of Each Level
Level 1 Level 2 Level 3 Level 4 Level 5 Level 6
Case Packing