Clear One BMA 360D User manual

Reference Manual
BMA 360D Commands
DOC-0579-001v1.0 September 2023
Supported Products:
BMA 360D

ClearOne®Contacts
Headquarters Headquarters
5225 Wiley Post Way Suite 500 Tel: +1.801.975-7200
Salt Lake City, UT 84116
Sales Technical Support
Tel: [phone] Tel: [phone]
[email protected] [email protected]
Notices
BMA 360D Commands Reference Manual
ClearOne Part Number: DOC-0579-001v1.0 September 2023
© 2023 ClearOne Inc. - All rights reserved. Information in this document is subject to change without notice. Other
product names may be registered trademarks of their respective owners who do not necessarily endorse ClearOne or
ClearOne’s products in the United States and/or other countries.

Contents
3
1. Concepts ..........................................................................................................................4
1.1 Introduction....................................................................................................................4
1.2 Connection Properties................................................................................................4
2. BEAMREPORT...............................................................................................................5
3. BREPORT.........................................................................................................................5
4. BFZONE ............................................................................................................................5
5. DANTEIP ...........................................................................................................................5
6. DANTEMAC.....................................................................................................................5
7. GAIN....................................................................................................................................6
8. HELP ...................................................................................................................................6
9. IPADDR..............................................................................................................................6
10. LBO ...................................................................................................................................6
11. LEDBLINK .....................................................................................................................6
12. LEDBRIGHT..................................................................................................................7
13. LEDCOLOR...................................................................................................................7
14. LOCATE ..........................................................................................................................7
15. MACADDR.....................................................................................................................7
16. MUTE ..............................................................................................................................8
17. NAME ..............................................................................................................................8
18. RESET..............................................................................................................................8
19. SERIAL............................................................................................................................8
20. VER....................................................................................................................................8

BMA 360D Commands
4DOC-0579-001v1.0 September 2023
Reference Manual
Back to Table of Contents
1. Concepts
1.1 Introduction
This document describes communication parameters, text commands and associated responses available with the
BMA 360D.
1.2 Connection Properties
Establish a TCP connection using the IP address of the BMA 360D and port #3603.
For testing purposes, a terminal emulator, such as Tera Term, can be used to test the commands.
To see typed characters, Local Echo must be enabled in your terminal emulation software.
To see a list of all the commands type HELP and press return.
For guidance on specific commands, type the command name followed by a question mark.
Example:
VER ?”

BMA 360D Commands
5DOC-0579-001v1.0 September 2023
Reference Manual
Back to Table of Contents
2. BEAMREPORT
Generates a single all beam report of current activity status.
Query format: BEAMREPORT
Response format: BEAMREPORT [b12][b11][b10][b9][b8][b7][b6][b5][b4][b3][b2][b1]
[bx] = 1 Active beam, 0 = Inactive beam
3. BREPORT
Initiate or halt continuous reporting of active beams.
Command format: BREPORT [x]
[X] = 0 Report disable, 1 Report averaged active beam, 2 Fast reporting of active beams
Query format: BREPORT
Response format: BEAMREPORT [b12][b11][b10][b9][b8][b7][b6][b5][b4][b3][b2][b1]
[bx] = 1 Active beam, 0 = Inactive beam
4. BFZONE
Enable/disable specific beams.
Command format: BFZONE [beam] [enable]
[beam] = 1 to 12
[enable] 1 = on, 0 = off
Query format: BFZONE [beam]
Response format: BFZONE [beam] [enable]
5. DANTEIP
Reports the IP address of the Dante interface.
Query format: DANTEIP
Response format: DANTEIP [IP address}
6. DANTEMAC
Reports the MAC address of the Dante interface.
Query format: DANTEMAC
Response format: MACADDR [MAC address]

BMA 360D Commands
6DOC-0579-001v1.0 September 2023
Reference Manual
Back to Table of Contents
7. GAIN
Adjust or query gain settings of the SmartMix output, Speaker outputs, or AEC reference input.
Command format: GAIN [channel] [group id] [value]
[channel] = 1 to 4
[group id] V = SmartMix, S = Speaker, R = AEC reference
[value] = -65 to 20
Query format: GAIN [channel] [group id]
Response format: GAIN [channel] [group id] [value]
8. HELP
Shows all text commands in alphabetical order.
Query format: HELP
Response format: [Available command list]
9. IPADDR
Reports the IP Address assigned for control interface.
Query format: IPADDR
Response format: IPADDR [IP Address]
10. LBO
Last Beam On, adjust or query if the Last Beam active will be reported when queried.
Command format: LBO [enable]
[enable] 1 = On, 0 = Off
Query format: LBO
Response format: LBO [enable]
11. LEDBLINK
Adjust or query LED blinking for a given condition.
Command format: LEDBLINK [state] [blink]
[state] 1 = Muted, 0 = Unmuted
[blink] 1 = On, 0 = Off
Query format: LEDBLINK [state]
Response format: LEDBLINK [state] [blink]

BMA 360D Commands
7DOC-0579-001v1.0 September 2023
Reference Manual
Back to Table of Contents
12. LEDBRIGHT
Adjust or query LED brightness for a given condition.
Command format: LEDBRIGHT [state] [bright]
[state] 1 = Muted 0 = Unmuted
[bright] 0 = Off, 1 = High, 2 = Medium, 3 = Low
Query format: LEDBRIGHT [state]
Response format: LEDBRIGHT [state] [bright]
13. LEDCOLOR
Adjust or query LED color for a given condition.
Command format: LEDCOLOR [state] [color]
[state] 1 = Muted, 0 = Unmuted
[color] 1 = Red, 2 = Orange, 3 = Yellow, 4 = Green, 5 = Blue, 6 = Indigo, 7 = Violet, 8 = White
Query format: LEDBRIGHT [state]
Response format: LEDCOLOR [state] [color]
14. LOCATE
Initiate or query the BMA 360D locate LED mode.
Command format: LOCATE [name] [enable]
[name] = The programmed BMA name
[enable] 1 = enable locate mode, 2 = disable locate mode
Query format: LOCATE
Response format: LOCATE [name] [enable]
15. MACADDR
Query the MAC address for the control IP interface.
Query format: MACADDR
Response format: MACADDR [MAC Address]

BMA 360D Commands
8DOC-0579-001v1.0 September 2023
Reference Manual
Back to Table of Contents
16. MUTE
Adjust or query mute settings of the BMA 360D microphone, individual beam silencing status, individual speaker
channels or AEC reference input.
Command format: MUTE [channel] [group id] [value]
[channel] = 1 to 12
[group] V = SmartMix, S = Speaker, B = Beam (Silenced status), R = AEC Reference
[Value] 1 = Muted/Silenced, 0 = Unmuted
Query format: MUTE [channel] [group id]
Response format: MUTE [channel] [group id] [value]
17. NAME
Adjust or query the Device Name.
Command format: NAME [string]
[string] = Text up to 40 characters.
Query format: NAME
Response format: NAME [string]
18. RESET
Causes a soft resets of the BMA 360D and retains all settings.
Command format: RESET
Response format: RESET
19. SERIAL
Returns the serial number of the BMA 360D .
Query format: SERIAL
Response: [Serial Number]
20. VER
Return the firmware revision of the BMA 360D .
Query format: VER
Response format: VER [version number]