Cleveland E-Zee Thunderstreak F-84F User manual

E
E
E
Top
Top
Top
E
Top
Top
Top
Top
A
A
A
Top
A
D
D
D
Top
Top
Top
D
Top
B
Top
B
B
B
Top
Top
Top
C
C
C
Bottom
Bottom
Bottom
C
Bottom
0123
Inches
F
Bottom
F
Bottom
F
Bottom
F
Bottom
F
Top
F
Top
F
Top
F
Top
H
T
I
Nose
L

E
E
E
Top
Top
Top
E
Top
Top
Top
Top
A
A
A
Top
A
D
D
D
Top
Top
Top
D
Top
B
Top
B
B
B
Top
Top
Top
C
C
C
Bottom
Bottom
Bottom
C
Bottom
0123
Inches
F
Bottom
F
Bottom
F
Bottom
F
Bottom
F
Top
F
Top
F
Top
F
Top
H
T
I
Nose
L

E
E
E
Top
Top
Top
E
Top
Top
Top
Top
A
A
A
Top
A
D
D
D
Top
Top
Top
D
Top
B
Top
B
B
B
Top
Top
Top
C
C
C
Bottom
Bottom
Bottom
C
Bottom
0123
Inches
F
Bottom
F
Bottom
F
Bottom
F
Bottom
F
Top
F
Top
F
Top
F
Top
P
K
M
Tail
R

E
E
E
Top
Top
Top
E
Top
Top
Top
Top
A
A
A
Top
A
D
D
D
Top
Top
Top
D
Top
B
Top
B
B
B
Top
Top
Top
C
C
C
Bottom
Bottom
Bottom
C
Bottom
0123
Inches
F
Bottom
F
Bottom
F
Bottom
F
Bottom
F
Top
F
Top
F
Top
F
Top
P
K
M
Tail
R

E
E
E
Top
Top
Top
E
Top
Top
Top
Top
A
A
A
Top
A
D
D
D
Top
Top
Top
D
Top
B
Top
B
B
B
Top
Top
Top
C
C
C
Bottom
Bottom
Bottom
C
Bottom
0123
Inches
F
Bottom
F
Bottom
F
Bottom
F
Bottom
F
Top
F
Top
F
Top
F
Top

E
E
E
Top
Top
Top
E
Top
Top
Top
Top
A
A
A
Top
A
D
D
D
Top
Top
Top
D
Top
B
Top
B
B
B
Top
Top
Top
C
C
C
Bottom
Bottom
Bottom
C
Bottom
0123
Inches
F
Bottom
F
Bottom
F
Bottom
F
Bottom
F
Top
F
Top
F
Top
F
Top

E
E
E
Top
Top
Top
E
Top
Top
Top
Top
A
A
A
Top
A
D
D
D
Top
Top
Top
D
Top
B
Top
B
B
B
Top
Top
Top
C
C
C
Bottom
Bottom
Bottom
C
Bottom
0123
Inches
F
Bottom
F
Bottom
F
Bottom
F
Bottom
F
Top
F
Top
F
Top
F
Top
G
N
S
D
F
Bottom
F
Bottom
F
Top
F
Top

E
E
E
Top
Top
Top
E
Top
Top
Top
Top
A
A
A
Top
A
D
D
D
Top
Top
Top
D
Top
B
Top
B
B
B
Top
Top
Top
C
C
C
Bottom
Bottom
Bottom
C
Bottom
0123
Inches
F
Bottom
F
Bottom
F
Bottom
F
Bottom
F
Top
F
Top
F
Top
F
Top
E
Top
E
Top
Top
A
Top
A
D
Top
D
Top
B
Top
B
Top
C
Bottom
C
Bottom
Fuselage Assembly Template
Fuselage Assembly Template

E
E
E
Top
Top
Top
E
Top
Top
Top
Top
A
A
A
Top
A
D
D
D
Top
Top
Top
D
Top
B
Top
B
B
B
Top
Top
Top
C
C
C
Bottom
Bottom
Bottom
C
Bottom
F
Bottom
F
Bottom
F
Bottom
F
Bottom
F
Top
F
Top
F
Top
F
Top
Cleveland E-Zee F-84
Landing Gear Patterns
Make from .025” Music Wire
Use 1/2” Wheels
Canopy Mold
0123
Inches
Main Nose
This model is intended to be catapult or Hi-Start launched. For that reason the parts should
be 1/16” thick as was the case for the original kit. Since these layouts are intended to be
printed on 1/32” balsa, a second layer for each part has been provided. For the fuselage
pieces the layer that will be inside does not have any graphics, just an outline.
If iron-on transfer paper will be used to transfer the graphics to balsa sheet, use 1/16” balsa
and skip the second layer parts. For this model the iron-on transfer paper method is probably
the best to use. Select relatively light balsa, 6.5 to 7.25 lb/ft3.

1.
Glue fuselage formes F to the back C as shown. A 1/16" wide slot
will be formed.
Use the fuselage assembly template as an alignment guide and
glue formers C/F and D to the fuselage sides L and R. DO NOT
GLUE THE TEMPLATE. Note that former F faces to the rear.
2. 3.
4. 5. 6.
7. 8. 9.
Glue the nose and tail rings in place. Sand them to shape once
the glue has set.
Glue formers A, B, and E to the fuselage sides. Use rubber
bands to hold the sides against the formers while the glue sets.
Sand a bevel on the edges of fuselage top H and bottom M.
Glue H and M to the fuselage assembly. Use rubber bands to
hold things while the glue sets.
Bevel the edges of fuselage corner pieces I, P, K, and T. Glue
I,P,K,T to the fuselage assembly. Again, use rubber bands to
hold the pieces in place while the glue sets.
Glue a wing rib to the bottom of each wing panel. Use the two
small marks on the top of the wing as a location guide.
Apply some glue to the wing slots in fuselage former F. Slide the
wing panels into the slots in the fuselage. Apply some additional
glue to the joint between the wing panels and the fuselage sides.
F
F
Top
Bottom
C
Assembly template
D
F
C
A
B
C
D
E
H
M
Bevel
I
P
K
T
Slots to the rear
If laminated 1/32" balsa parts are being used to build this
model, cut all parts from the balsa sheet and then glue the
corresponding halves together. The interior fuselage only have
the outlines printed.