Clicker Clt1 User manual

The Receiver DIP switch has three positions labeled “+”, “0”

and “-”. The “0” setting cannot be used with the clicker remote.

1) Reset switches: 1 to “-” and positions 2 through 9 to a random

setting using “+” and the “-”. DO NOT USE THE “O” SETTING.

2) Gather any existing remotes and open to expose the DIP switches. Reset

the DIP switch to match the newly coded receiver. Note: some three button remotes do

not have a #1 switch. Match the 2 through 9 to the receiver. On three button remotes

the large button is now programmed to activate the door. 3) Test all the newly coded

remote controls to be sure that they operate the door before proceeding to the BRAND MODE SETTING.

After determining that the Receiver has a yellow, white or gray

learn button, 1) Gather any existing remotes and open to expose

the DIP switches labeled “+”, “0” and “-”. 2) Reset switches: 1 to

“-” and positions 2 through 9 to a random setting using “+” and

the “-”. DO NOT USE THE “0” SETTING, SET ALL REMOTES

TO THE SAME SETTING. On three button remotes the large button is

now programmed to activate the door. 3) The recoded remotes must be

programmed to the receiver. Press and release the smart-learn button.

Then press and hold the existing remote push button for three seconds.

4) Test all the newly coded remote controls to be sure that they operate the

door before proceeding to the BRAND MODE SETTING.

With this type receiver, the existing remotes do not contain DIP switches.

Proceed to BRAND MODE SETTINGS.

LOCK

LIGHT

Motor

Unit &

Receiver

Wall Mounted

Control

Remote Control

The clicker remote can be programmed to operate up to 2 garage door openers or gates,

including different brands. All programming is done using the:

• Brand switch

• Transmitter DIP switch

• Transmit push buttons A and B, and LED indicator

Determine the BRAND of the existing garage door opener or handheld remote controls. If all

remote controls are lost, the BRAND is located on the ceiling mounted motor unit or on the

receiver near the flexible wire antenna. Proceed to the SECTION indicated on the BRAND chart

below.

Note: If programming to more than one opener, after programming button “A” refer to brand

chart, and follow the instructions pertaining to the brand you wish to program into button “B”.

When the remotes range is diminished, operation is intermittent, or the LED dims, replace the

battery. Memory is not lost when the battery is removed. Note: Dispose of old batteries

properly.

Model No. CLT 1

Universal Garage Door Opener Remote Control

CLICKER

Proceed to appropriate section.

Step 4 - When LED flashes,

release both buttons.

Step 5 - Press the button you wish to operate the

opener (your choice).

Step 6 - Programming is complete, to test, press the

button selected to activate garage door.

Step 2

Step 1

Existing

Remote

Clicker

Remote

Match

existing

codes.

Set extra

switches off.

➡

SECTION III

• Open existing remote; determine if there are 9 or 12 code switch settings.

• Set brand mode switches on clicker remote.

• Program clicker remote push button.

Step 1

ORANGE/RED

SMART-LEARN BUTTON

SECTION I SECTION II

• Determine specific brand and circle above. • Open existing remote to expose code switches.

• Set brand mode switches on clicker remote. • Program clicker remote push button.

➡

Chamberlain, Sears, LiftMaster, Master Mechanic, DoIt

➡

ON ON OFF OFF

OFF ON ON OFF

OFF OFF OFF OFF

STANLEY

ON OFF OFF OFF

MULTI-CODE

OFF ON OFF OFF

LINEAR/MOORE-O-MATIC

OFF OFF ON OFF

GENIE 9 SWITCH

ON OFF ON OFF

GENIE 12 SWITCH

SECTION I - Chamberlain, Sears, LiftMaster,

Master Mechanic, DoIt

SECTION II - Stanley, Multi-code, Linear,

Moore-O-Matic

SECTION III - Genie

BRAND

CHART

LED

Button B

Button A

Brand Switch

Dip Switch

Battery

Slide battery

door down

& Remove

Preparation

Determine if your motor unit/receiver system has DIP switches or a smart-learn button.

(Locate the small gray wire antenna. Some

models require removing the light lens.)

• If the Receiver has 9 DIP switches Proceed to TYPE A

• If the Receiver has a yellow, white, or gray smart-learn button, proceed to TYPE B

• If the Receiver has a green, red, or orange smart-learn button, proceed to TYPE C

SMART-LEARN

BUTTON

➡

DIP SWITCHES

TYPE

➡

✚

–

KG KG

➡

Use this

button

KG KG

➡

Remote

push button

TECHNICAL SUPPORT: 800-442-1255 (MONDAY-FRIDAY 6AM-7PM CST; SATURDAY 8AM-6PM)

Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie is a Trademark of Overhead Door

Corporation. Linear and Multi-Code are Trademarks of Linear Corporation. Master Mechanic is a Trademark of TruServ.

Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark of The Stanley Works.

DoIt is a trademark of DoIt Best Corporation.

➡

Existing

Remote

Match

existing codes.

Set extra

switches off.

➡

Clicker

Remote

✚

–

123456789

RANDOM 2-9

DO NOT USE

✚

–

123456789

RANDOM 2-9

DO NOT USE

Use this

button

➡

FOR TYPE A AND B

ON ON ON OFF

GREEN SMART-LEARN

BUTTON

➡

Code switch

settings are

not used.

➡

Code switch

settings are

not used.

➡

- Stanley, Multi-Code, Linear, Moore-O-Matic

- Genie - 9 Code Switch, Genie - 12 Code Switch

Step 1

- Step 1

Step 3 - Press and hold both

buttons for 5 seconds

or until LED begins to

flash.

Step 4 - When LED flashes,

release both buttons.

Step 5 - Press the button you wish to operate the

opener (your choice).

Step 6 - Programming is complete, to test, press the

button selected to activate garage door.

Step 2

Existing

Remote

Clicker

Remote

Match

existing

codes.

Set extra

switches off.

➡

Step 3 - Press and hold

both buttons for 5

seconds or until LED

begins to flash.

BRAND MODE SETTINGS

- Set switches on clicker remote

Step 2 - Press and hold both buttons for 5 seconds or until LED begins to flash.

Step 3 - When LED flashes, release both buttons.

Step 4 - Press the button you wish to operate the opener (your choice).

For type A & B, proceed to step 6. For type C, continue on to Step 5.

KG KG

A. Press and release

Smart-Learn

button.

Step 6 -

Programming is complete, to test, press the button selected to activate garage door.

FOR TYPE C

– OR –

B. Press and hold button

selected in Step 4 for 3 seconds.

Continue to Step 2.

Step 5

Note: Use pen or small screwdriver

to move dip switches.

123456789

1234

➡

10 1112

➡

UP Position is ON

DOWN Position is OFF

UP Position is ON

DOWN Position is OFF

WARNING

CAUTION WARNING

WARNING

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play

with remote control transmitters.

• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no

obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely closed. Never permit anyone to cross

path of moving gate or door.

NOTICE: To comply with FCC and or Industry Canada rules, adjustment or modifications of this receiver and/or transmitter are

prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device

may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.