Climate+ CAC-8000X User manual

OUTDOOR AIR COOLER
CAC-8000X
INTRODUTION
Thank you for purchasing our product. we trust It will give you long and trouble-free service.
WARNING
1. This appliance is not intended for use by persons(including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
2. Children should be supervised to ensure that they do not play with the appliance.
3. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
4. Unplug the appliance during filling and cleaning.

Technical specification
MODEL
CAC-8000X
Max air flow(m3/h)
8000m3/h
voltage
220V-240V
Frequency
50/60hz
Rated power
360 W
Water consumption
8L/H
Water capacity
80L
Size
800*475*1380mm
Weight
53kg
Effective area
60m2
Advantages:
1. 3 speed for the wind.
2. The thicker and bigger cooling pad for better heat
absorption.
3. Wheel footing is easy moving.
4. Big capacity for the water tank.
5. Removable cooling pad.
6. Easy for clean.

IMPORTANT REMINDERS
Please read the manual carefully before operating the cooler.
A) Operating conditions:
1- Temperature:18°C to 45° C, water temperature:<45°C.
2- Power supply must not exceed the required voltage (+/-) 5%.
3- Air supply must be largely free of dust or extra cleaning is required.
B) Protect the power cable from vehicle or foot traffic. Connection to incorrect electric voltage or faulty
installation, will cause danger of electric shock.
C) Other tips for cooler use:
1- Keeps doors and windows open top allow fresh air to enter, and treated air to exit, when cooler is
operating.
2- Flashing red light on the control panel means water level in reservoir is low.
3- Rinse the reservoir with fresh water and clean prior to use after a period where the cooler has
not been in operation.
4- Take care when moving the air cooler, especially when it is full of water. Pushing too hard will
cause the cooler to overbalance and tip over, which may cause injury and will damage the cooler.
CLEAN AND PROTECTION
1. AIR FILTER
Switch off the power and take away the plug, pull out the handle.
Then you can use the cleaner to wash it.
2. Outside the machine
Clean with the dry-wet cloth
3. Cooling pad
Switch off the power and take away the plug. First take out the air
filter, then for the cooling pad use the soft brush to wash it.
4. Water tank
Switch off the power and open the back cooling pad. Use the cloth
and clean water to wash it.

Trouble shooting
Problem
Reason
Solution
Unable to start the
fan
Power failure.
Loose PCB
connection.
Fuse burned out.
Check power
supply.
Check PCB
connection.
Replace fuse.
Lower or no airflow
Fan damaged.
Cooling pad
jammed.
Filter jammed.
Starting capacitor
damaged.
Fan stuck.
Replace fan.
Clean cooling
pad.
Clean filter.
Replace
capacitor.
Check fan and its
housing.
No cooling airflow
Water lack.
Cooling pad
jammed.
Water pump
damaged.
Water sensor
damaged.
Water pipes drops
off.
Water distributor
jammed.
Fill water into
tank.
Clean cooling
pad.
Replace water
pump.
Replace water
sensor.
Tighten water
pipe.
Check water
distributor.

Grill does not swing
Swing motor
damaged.
Swing motor
crankshaft drops
off.
Replace swing
motor.
Check swing
motor
crankshaft.
Leak from drainage
outlet
Loose drainage
cap.
Rubber O-ring
damaged.
Tighten cap.
Replace O-ring.
Water splashes out
of grill
Water pipe drops
off.
Tighten water
pipe.
Note: this trouble shooting is for reference purpose
only. If any technical assistance is needed. Please
contact your distributor for service/repair.