Closet Maid TOTALSLIDE PRO Instruction sheet

04-10135-00 09/19
The following scenarios show detailed installation guidelines when
installing the TotalSlide® Pro system components. In general, please
keep in mind the following when installing TotalSlide Pro:
TotalSlide Pro components are compatible with all TotalSlide Hardware
The TotalSlide Pro Hang Rod Assembly is specically designed to install
on ClosetMaid 12 in. and 16 in. All-Purpose (SuperSlide/Linen) Shelving
as well as Heavy Duty Shelving
We suggest you install the Hang Rod Assembly on the shelf at the
warehouse prior to transporting for installation (per instruction in
TotalSlide Pro Installation Video)
Please follow TotalSlide Pro Hang Rod Assembly handling instructions
(located after the installation guidelines) when moving or transporting
sections of the assembly
Hardware
Installation Guidelines
© 2019 ClosetMaid LLC | Ocala, FL 34471 | 1-800-874-0008 | ClosetMaidPro.com

1
Installation Guidelines
Open to Open Hang Rod Installation
Installation example - Hang Stops end a Hang Rod section in the middle of All-Purpose
(Linen/SuperSlide) shelving:
Use Hang Stops to end a hanging section of Hang Rod Assembly on a shelf.
Closed to Closed Hang Rod Installation
Installation example - When Shelf Stops end a Hang Rod section at the ends of
All-Purpose (Linen/SuperSlide) shelving:
Use Shelf Stops to end a hanging section of Hang Rod Assembly on a shelf at the ends.
Hang Rod Assembly/
Hang Stop Conguration
© 2019 ClosetMaid LLC | Ocala, FL 34471 | 1-800-874-0008 | ClosetMaidPro.com

2
Installation Guidelines
Center Stack - End Stop
Installation example - TS Pro Hang Rod ends on outside
of center stack:
When shelf and hang rod terminate at the point on the outside of a
support post, use a shelf stop to end hang rod and shelf 1 in. on out-
side of the support post.
Center Stack Installation
1 in.
1 in. 1 in.
© 2019 ClosetMaid LLC | Ocala, FL 34471 | 1-800-874-0008 | ClosetMaidPro.com
Create Hanging Space
inside Center Stack
Installation example - Using a TS Pro Hang Stop
in combination with an All-purpose shelf and TS
Pro Hang Rod:
Use a TS Pro Hang Stop 1 in. from the inside of a sup-
port post. Cut shelf so that 1 in. of overhang is repre-
sented on outside of each support post.
Hanging Space
outside of Center Stack
Installation example - TS Pro Hang Rod ends
on outside of center stack and shelf continues:
When shelf continues through center stack but hang
rod ends at support post, use hang stop to end hang
rod at 1 in. on the outside of support post
1 in.
Installation Example:

3
Installation Guidelines
Installation example - Using the TS Pro Corner Rounder, please note the
following guidelines:
For any TS Pro Corner Rounder installation it is required to have at least 1 in. of TS Pro Hang Rod
insertion into TS Pro Corner rounder tube
In any TS Pro Corner Rounder installation it is required to have no more than 3 in. of unsupported space from
the edge of a Corner Rounder
When installing the Rod Joiner, make sure that there is at least 1 in. of Hang Rod insertion into each side of the
tube. The Rod Joiner should be positioned so that both ends of the tube rest against the side of each hook (as
shown). Trimming of a Hang Rod section may need to occur if there is any overlap.
Corner & Rod Joiner
Installations
© 2019 ClosetMaid LLC | Ocala, FL 34471 | 1-800-874-0008 | ClosetMaidPro.com
1 in.
<3 in. <3 in.
1 in.
1 in.

4
Installation Guidelines
Installation example - Using LP SuperSlide End Bracket:
Install Hang Rod Assembly section on all shelves prior to shelf installation. Snap TS Pro Hang Rod Assembly
into desired location onto the shelf. Place Hang Stop 1 in. away from edge of End Bracket.
Installation example - Installing TS Pro Hang Rod with TotalSlide End Bracket:
Install Hang Rod Assembly section on to shelf prior to shelf installation. Snap TS Pro Hang Rod Assembly into
desired location onto the shelf. The hang rod should be even with end of shelf. Rotate shelf and Hang Rod into
bracket until secure t.
End Bracket Installation
© 2019 ClosetMaid LLC | Ocala, FL 34471 | 1-800-874-0008 | ClosetMaidPro.com
1 in.

The following instructions outline proper handling procedures for the
TotalSlide® Pro Hang Rod Assembly. Please follow these handling
instructions when moving or transporting sections:
The TotalSlide Pro Hang Rod Assembly was designed to be packed and
unpacked in a sequential manner that allows them to nest and save space.
It is important that you follow proper handling instructions. Make sure to
stock, transport, and handle the sections in a nested manner that keeps the
hooks tangle free.
Hang Rod Assembly
Handling Instructions
© 2019 ClosetMaid LLC | Ocala, FL 34471 | 1-800-874-0008 | ClosetMaidPro.com
04-18069-00
IMPORTANT

1
Position the TS Pro hang rod assembly on a
table right side up.
1)
2)
3)
If any of the Hang Rod Assembly
sections have shifted in the
package, reposition the assembly
so that the hooks are seated on
the at top.
Unfold the side caps to make
room to slide the Hang Rod
Assembly sections out of the
carton.
© 2019 ClosetMaid LLC | Ocala, FL 34471 | 1-800-874-0008 | ClosetMaidPro.com
Hang Rod Assembly Unpacking Instructions

© 2019 ClosetMaid LLC | Ocala, FL 34471 | 1-800-874-0008 | ClosetMaidPro.com
2
Grip the bottom of the rst Hang Rod Assembly
in the locations as shown.
4)
5)
6)
7)
8)
Only slide one section at a time. Slide the rst
Hang Rod Assembly section to the left about 6 in.
as shown.
Rotate the Hang Rod Assembly
forward (as shown) making sure
that the back of the hooks clear
the others.
Once the back of the hooks have cleared the other
Hang Rod Assembly’s, lift it straight up and carry
to the desired location
Repeat the same procedure until the carton is empty
Hang Rod Assembly Unpacking Instructions

The following scenarios show detailed installation guidelines
when installing the TotalSlide® Pro Hang Rod Assembly on an
All-Purpose (Linen/SuperSlide) Shelf. Please note the following:
Please follow proper Hang Rod Assembly handling instructions to ensure
easy maneuvering of the sections. It is important to keep Hang Rod
Assembly sections in alignment when moving, transporting, and installing.
It is suggested to install the Hang Rod Assembly on the shelf at the
warehouse prior to transporting for installation. (See the TotalSlide Pro
Installation Video)
Hang Rod Assembly & Hang Stop
Installation Guidelines
© 2019 ClosetMaid LLC | Ocala, FL 34471 | 1-800-874-0008 | ClosetMaidPro.com
04-18069-00

© 2019 ClosetMaid LLC | Ocala, FL 34471 | 1-800-874-0008 | ClosetMaidPro.com
1
Hang Rod Assembly Installation Guidelines
1)
2)
3)
4)
5)
Place the shelf on its at side with the lip facing
towards you
Remove the All-Purpose (Linen/SuperSlide) shelf and
transport it to a at surface (preferably clean area)
Move the Hang Rod Assembly section into position
and place it on the at surface (hook end down) with
the opening facing towards you as shown
Lift the Hang Rod Assembly section and position in
between the deck wires on the shelf
Position the Hang Rod Assembly so that the edge of
the assembly rod aligns with the edge of the shelf (as
shown)

© 2019 ClosetMaid LLC | Ocala, FL 34471 | 1-800-874-0008 | ClosetMaidPro.com
2
Hang Rod Assembly Installation Guidelines
6)
7)
8)
9)
10)
Lift the shelf and Hang Rod Assembly section and
begin to move the it under the cross wires and
towards the front lip of the shelf
Place the front of the Hang Rod Assembly hooks
over the top rod on the front lip of the shelf
Rotate the Hang Rod Assembly section upwards
so that the back bottom of the hooks rest on the
second cross rod
Hang Rod Assembly should be attached and
resting on the at surface (as shown)
Snap each hook into place by lifting the hook
over the back cross rod

© 2019 ClosetMaid LLC | Ocala, FL 34471 | 1-800-874-0008 | ClosetMaidPro.com
3
Hang Rod Assembly Installation Guidelines
11)
12)
13)
Measure the Hang Rod Assembly and shelf
section per standard TotalSlide measuring
practices
Cut shelf and Hang Rod Assembly
at desired locations
Install shelf end caps where needed
and prepare for transport to the site

© 2019 ClosetMaid LLC | Ocala, FL 34471 | 1-800-874-0008 | ClosetMaidPro.com
4
Hang Rod Assembly
Installation Guidelines (On -Site)
1)
2)
3)
4)
Transport shelf into desired location for attach-
ment of the Hang Rod Assembly
Transport Hang Rod Assembly section into same
desired location being careful to keep the shelf
and Hang Rod Assembly separate from one
another
Keeping the Hang Rod Assembly section and
shelf separate, begin to measure the section (if
necessary)
Measure the Hang Rod Assembly section and
mark at proper dimension(s)

© 2019 ClosetMaid LLC | Ocala, FL 34471 | 1-800-874-0008 | ClosetMaidPro.com
5
Hang Rod Assembly
Installation Guidelines (On -Site)
5)
6)
7)
Cut the Hang Rod Assembly section(s) at
proper dimension(s)
Lift the Hang Rod Assembly section and shelf
together. Position the Hang Rod Assembly
section so that it is aligned with the end of the
shelf and begin to place the section behind
the second cross rod
Rotate the Hang Rod Assembly so that the
front of the hook captures the top rod of the
front lip

© 2019 ClosetMaid LLC | Ocala, FL 34471 | 1-800-874-0008 | ClosetMaidPro.com
6
Hang Rod Assembly
Installation Guidelines (On -Site)
8)
9)
Rotate the back end of the Hang Rod Assembly
and place on at surface
Snap each hook into place by lifting the hook
over the back cross rod and prepare to install

© 2019 ClosetMaid LLC | Ocala, FL 34471 | 1-800-874-0008 | ClosetMaidPro.com
7
Hang Stop Installation Guidelines
1)
2)
3)
4)
Slide the Hang Stop over the Hang Rod at the
end of the rod.
Rotate the top of the Hang Stop toward the
top of the front lip of the shelf.
Snap the top of the Hang Stop into onto the
top of the front lip of the shelf.
Hang Stop should look as pictured when
installed.