Clover OW1415 User manual

MONITOR
10 89
4
3 112
5 7
DC-IN
CH1
VIDE O- IN
A
UDIO -IN
CH2 CH3 C H4
VIDE O OU T
AU DIO OUT
17 18
20
15
19
16
1. POWER ON/OFF button
Turn the monitor ON/OFF.
2. CH1 button
Pressing this button enables the conversion to CAMERA 1 in MANUAL mode and the corresponding
LED is lit.
3. CH2 button
Pressing this button enables the conversion to CAMERA 2 in MANUAL mode and the corresponding
LED is lit.
4. CH3 button
Pressing this button enables the conversion to CAMERA 3 in MANUAL mode and the corresponding
LED is lit.
5. CH4 button
Pressing this button enables the conversion to CAMERA 4 in MANUAL mode and the corresponding
LED is lit.
6. AUTO button
When pressing this button, the unit is in auto mode and the corresponding LED is lit.
7. VCR button
Press this button to view the recorded images from the VCR.
8. Brightness control ( )
Adjusts the picture brightness. Turn this control clockwise to increase the brightness, and turn it
counterclockwise to reduce the brightness.

9. Contrast control ( )
Adjusts the picture contrast. Turn this control clockwise to increase the contrast, and turn it
counterclockwise to reduce the contrast.
10. Vertical Hold control ( )
This control is used to lock the vertical position of the picture.
11.Auto dwell time control ( )
Adjusts the auto dwell time. Turn this control right to reduce the time length and turn it left to increase the
time length.
12.Volume control ( )
Adjusts the audio level. Turn this control right to increase the audio level and turn it left to reduce the
audio level.
13. SYSTEM switch
Turn the switch on or off depends on the frequency of AC power source in your area (60 Hz
in U.S.A.).
14. Speaker
Audio out.
15. CAMERA IN (CH1~CH4)
Connect a camera to each input jack, which has 4-pin Din
16. AUDIO IN
This is an AUDIO input RCA jack for VCR.
17. VIDEO IN
This is a VIDEO input RCA jack for VCR.
18. AUDIO OUT
This is an AUDIO output RCA jack for VCR.
19. VIDEO OUT

This is a VIDEO output RCA jack for VCR.
20. DC IN jack
Plug the DC plug of the power adapter (supplied as a standard accessory) into
this jack and connect it to an AC outlet.
PIN CONFIGURATION FOR 4-PIN DIN JACK
CAMERA
(Indoor camera) (Outdoor camera)
Moni tor
1
2
4
3
7
65
1
2
5
3
7
1. Lens (4mm)
Indoor camera: Turn the CS mount lens clockwise or counter-clockwise to get the best picture.
Outdoor camera: Do not try to open the camera to adjust the focal length (already adjusted by
factory).

2. Infrared LEDs
Infrared LEDs let you see objects in the darkness.
3. CDS sensor
Turn the Infrared LEDs off during daytime, and turn it on at night automatically.
4. C-mic for Indoor camera only
High sensitivity condenser microphone.
5. 4-pin Din jack
Connect the one end of cable to this jack.
6. Tripod screw for Indoor camera
There is a tripod screw on the bottom of the indoor camera (Refer to installation).
7. Mounting bracket
INSTALLATION
1. Attach the mounting bracket to the wall or ceiling, wherever you want to install the camera. Locate
a wall stud or ceiling joist and secure the mounting bracket using the supplied screws.
2. Install the camera to the mounting bracket and firmly tighten the swivel.
3. Connect the one end of cable (supplied) to the Din jack on the rear of the camera and the other end
of cable to the monitor. Make sure that two arrows on the top of them should be aimed at each
other

Wall
(CAMERA)
(MONITOR)
MOUNTING
BRACKET
60’ cable CEILING
(CAMERA)
MOUNTING
BRACKET
60’cable
Fig.1
(MONITOR
)
CEILING
(CAMERA)
MOUNTING
BRACKET
60 ’ c abl e
60’ cable
MOU N T IN G
BRACKET
Wall
(CAMERA)
Fig.2