Clover REV055 User manual

MONITOR
FRONT
REAR
POWER ON/OFF SWITCH
Switch for the power on/off. If the monitor is turned on, the LED of power is lit.
2. CONTRAST
Adjust the picture contrast. Turn this control clockwise to increase the contrast, and
turn it counterclockwise to reduce the contrast.
3. BRIGHTNESS

Adjust the picture brightness. Turn this control clockwise to increase the contrast,
and turn it counterclockwise to reduce the brightness.
4. VOLUME
Adjust the audio level. Turn this control clockwise to increase the audio level, and
turn it counterclockwise to reduce the audio level.
5. CAMERA SELECTION
It can be connected up to 2 cameras on the monitor. Choose C1 (Camera1) or C2
(Camera2).
6. MODE SWITCH
MANU (Manual) MODE
In this mode, you can view the pictures from C1 (Camera1) or C2 (Camera2).
(See 14. DC POWER WIRES)
AUTO MODE
In this mode, you can view the pictures from C1 (Camera1) or C2 (Camera2) only
when selector lever is in the reverse position. You can’t view the picture from the
camera while you are driving (See 14. DC POWER WIRES).
7. DAY/NIGHT
Press this button for daytime to increase the brightness and press again for nighttime
to reduce the brightness.
8. C1 (CAMERA 1)
Connect the supplied camera to C1 (this system includes only one camera, ask your
dealer for an additional camera).
9. C2 (CAMERA 2)
Connect the additional camera to C2.
10. VIDEO OUTPUT
Composite video output for other devices such as VCR.

11. AUDIO OUTPUT
Audio output for other devices such as VCR.
12. EXT. SPEAKER
Connect the external speaker if you need.
13. MIRROR/NORMAL IMAGE
You can switch this Dip switch with (-) driver for mirror or normal image. You can
view the mirror image if it is in the lower position, you can view the normal image
when it is in the upper position (default setting: mirror image).
14. DC POWER WIRES
There are 4 different kinds of wires as follows.
GROUND: Connect the BLACK colored wire to vehicle’s chassis (Do not connect
it to the gas tank, the air bag and etc.).
DC 11V TO 32V (HOT): Connect the RED colored wire to the DC power line that
supplies DC 12V or 24V when ignition switch is in the “ON” position. The mode
switch on the front of the monitor must be in the manual mode. It doesn’t display
the picture on the screen in the auto mode.
BACK-UP LIGHT BULB: Connect the BROWN colored wire to the (+) terminal
of back-up (rear turn signal) light bulb. The screen displays the picture only when
the vehicle is in motion on the reverse. The mode switch on the front of the monitor
must be in the auto mode.
HOW TO INSTALL
1. INSTALLATION OF MONITOR

■Attach the mounting bracket to the dash-board (not airbag area) or ceiling, wherever you want to install the
monitor. Secure the bracket with the supplied screws as shown above.
■Connect the wire connector with 4 wires in polarity to the power in jack on the rear
of the monitor after connecting those wires as mentioned above (See14.DC POWER
WIRES).
■Fasten the monitor and sun-visor onto the mounting bracket with 4-screw knobs.
2. INSTALLATION OF CAMERA
Refer to the following illustrations for installation of camera.

■Unscrew on both sides of the camera and separate the mounting bracket and
sun visor from the camera.
■Screw the mounting bracket to proper place on your vehicle and assemble the
camera along with sun visor onto it.
Connect the one end of cable (supplied) to the 4-pin Din jack on the rear of camera and
the other end of cable to the monitor. Make sure that two arrows on the top of them
should be aimed at each other. After connecting, tighten the cable with locking ring
on the cable.
■To record, connect the cable (not supplied) to the VIDEO and AUDIO OUT ports on the
monitor and VIDEO and AUDIO IN ports on the VCR.